Opens in a new tab

LPS22HHTR

260-1260hPa MEMS pressure sensor, 0.5hPa accuracy, I2C/SPI, HLGA-10

6500

Effective Inventory

Image for reference only

Manufacturer Part:

LPS22HHTR

Package:

10-HLGA (2.00 x 2.00 x 0.73 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The LPS22HHTR is a STMicroelectronics high-performance MEMS nano pressure sensor functioning as a digital output barometer. It measures absolute pressure from 260 to 1260 hPa with 0.5 hPa accuracy, 0.65 Pa RMS noise, and 24-bit output resolution. The device supports I2C, SPI, and MIPI I3C interfaces with embedded FIFO, and operates from 1.7 V to 3.6 V in a 10-pin HLGA (2×2 mm) package.

Key Specifications

Pressure Range 260 to 1260 hPa
Accuracy 0.5 hPa absolute
Noise 0.65 Pa RMS
Resolution 24-bit
ODR 1 Hz to 200 Hz
Supply Voltage 1.7 V to 3.6 V

Features

  • 260-1260 hPa absolute pressure range
  • 0.5 hPa absolute accuracy
  • 0.65 Pa RMS noise
  • 24-bit pressure data output
  • Embedded 128-slot FIFO
  • I2C, SPI, and MIPI I3C interfaces
  • Programmable ODR from 1 to 200 Hz
  • 22,000 g shock survivability

Applications

  • Altimeters and barometers
  • Weather station equipment
  • Drone altitude hold
  • Wearable sport watches
Product Introduction: LPS22HHTR Product Introduction

The STMicroelectronics LPS22HHTR is an ultra-compact piezoresistive absolute pressure sensor functioning as a digital-output barometer with 0.5 hPa absolute accuracy and 0.65 Pa RMS noise. The device measures absolute pressure from 260 hPa to 1260 hPa (equivalent to altitude range of approximately -5,000m to +10,000m above sea level) with 24-bit output resolution. The ultra-small 2.0 x 2.0 x 0.73 mm HLGA package is 70% smaller than competing pressure sensors, enabling integration into smartphones, wearables, and drones where PCB area is at a premium. The embedded temperature compensation and factory calibration ensure accurate pressure readings without user calibration—the trimming values are stored in non-volatile memory and loaded automatically at power-on. The 128-slot FIFO buffer stores pressure and temperature data, allowing the host processor to remain in sleep mode until a batch of data is ready, reducing system power consumption. The configurable output data rate (1 Hz to 200 Hz) supports both slow weather-monitoring and fast altitude-tracking applications. Communication is via I2C (up to 400 kHz), SPI (up to 10 MHz), or MIPI I3C. The 22,000 g shock survivability ensures reliability in harsh mechanical environments such as drone crashes and industrial vibration.

Working Principle: LPS22HHTR Working Principle

The LPS22HH uses a silicon MEMS piezoresistive sensing element manufactured using ST’s dedicated MEMS process. A suspended silicon membrane deflects under applied pressure, inducing an imbalance in a Wheatstone bridge of piezoresistive elements embedded in the membrane. The analog output of the bridge is amplified by a low-noise instrumentation amplifier and converted to digital by a 24-bit sigma-delta ADC. An internal temperature sensor simultaneously measures the die temperature, and the digital logic applies factory-calibrated temperature compensation coefficients to the raw pressure reading. The compensated 24-bit pressure data and 16-bit temperature data are stored in output registers accessible via I2C/SPI. The FIFO buffer can store 128 samples of pressure and temperature data in six operating modes: bypass, FIFO, continuous (dynamic-stream), continuous-to-FIFO, bypass-to-continuous, and bypass-to-FIFO—enabling sophisticated data capture scenarios such as triggered burst recording. The programmable interrupt generator can assert the INT_DRDY pin on data-ready, FIFO threshold, or pressure threshold crossing events, enabling event-driven architectures that minimize host processor wake-ups.

Pin Description: LPS22HHTR Pin Definition and Functions
Pin Mnemonic Description
1 VDD_IO I/O supply (1.7-3.6V)
2 GND Ground
3 INT_DRDY Interrupt / data-ready output
4 SDI/SDA SPI data in / I2C data
5 SDO/SA0 SPI data out / I2C address LSB
6 CS SPI chip select (low=SPI, high=I2C)
7 SCL/SPC I2C clock / SPI clock
8 VDD Analog supply (1.7-3.6V)
9-10 RES Reserved (connect to GND)
Application Scenarios: In which products and applications is LPS22HHTR used
  • Smartphone altimeter with 0.5hPa accuracy enabling floor-level detection in indoor navigation applications
  • Drone barometric altitude hold with 200Hz ODR and 0.65Pa noise enabling <0.1m altitude resolution
  • Wearable weather station with FIFO buffering allowing host MCU sleep between 128-sample data bursts
  • Industrial gas metering with embedded temperature compensation maintaining accuracy from -40C to +85C
Alternative Models: What chips are recommended as replacements for LPS22HHTR
Model Manufacturer Key Difference
LPS27HHW ST Waterproof version, 260-1260hPa
BMP388 Bosch 300-1250hPa, 0.03hPa rel accuracy, larger
DPS310 Infineon 300-1200hPa, 0.5hPa accuracy, I2C/SPI
ICP-10111 TDK/InvenSense 10-120kPa, very low power, tiny WLCS

Recommend Parts

TMP275AIDR

0.5C I2C temp sensor, 12-bit, 2.7-5.5V, alert output, 8-SOIC

Brand: TI

Package: 8-SOIC (4.90 x 3.91 x 1.50 mm)

IN STOCK: 3681pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IL485E

NVE IL485E IsoLoop isolated RS-485 transceiver, 2.5kVrms isolation, 35Mbps, 16-SOIC WB

Brand: nve

Package: SOIC-16 WB

IN STOCK: 5280pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFS4227TRLPBF

IRFS4227TRLPBF – 200V N-Channel HEXFET PDP Switch Power MOSFET, 26 mΩ RDS(on), D2PAK (TO-263)

Brand: infineon

Package: D2PAK (TO-263)

IN STOCK: 4334pcs

Cargo cycle: 3-7 Days

The minimum order is 1

CD4070BM96

Quad 2-input XOR gate, 3-18V CMOS, 65ns at 10V, SOIC-14

Brand: TI

Package: SOIC-14 (8.75 x 3.9 x 1.5mm)

IN STOCK: 4245pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AB1526

Bluetooth 5.0 Dual Mode Audio SoC, TWS, AAC, Dual-mic ENC, Integrated Charger, BGA

Brand: airoha

Package: BGA

IN STOCK: 25000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LP2980IM5-5.0

50mA micropower ultra-low-dropout regulator, 5V, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.1 mm)

IN STOCK: 2557pcs

Cargo cycle: 3-7 Days

The minimum order is 1