Opens in a new tab

MAX232CPE

Dual RS-232 driver/receiver, 5V, charge pump, 120kbps, PDIP-16

8000

Effective Inventory

Image for reference only

Manufacturer Part:

MAX232CPE

Package:

PDIP-16 (7.62mm width, 2.54mm pitch, through-hole)

Brand:

Product Categories:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The MAX232CPE from Analog Devices (formerly Maxim Integrated) is a dual RS-232 driver/receiver that converts TTL/CMOS logic levels to RS-232 voltage levels from a single 5V supply using an integrated charge pump, requiring only four external 1µF capacitors in a PDIP-16 package.

Key Specifications

Drivers / Receivers 2 / 2
Supply Voltage 4.5V to 5.5V (single 5V)
Supply Current 8mA typical
Data Rate Up to 120kbit/s
Driver Output Swing ±8V typical loaded (±5V min per EIA-232)
Receiver Input Threshold 0.8V (LOW), 2.4V (HIGH)
Receiver Hysteresis 0.5V typical
Receiver Input Range ±30V
Driver Slew Rate 24V/µs unloaded, 10V/µs loaded
ESD Protection 2000V HBM (upgrade to MAX202 for 15kV)
Charge Pump Capacitors 4 × 1µF (external)
Operating Temperature 0°C to +70°C
Package PDIP-16 (7.62mm width)

Features

  • Meets TIA/EIA-232-F and ITU V.28 specifications
  • Operates from single 5V supply
  • Integrated dual charge pump generates ±10V
  • Requires only four 1µF external capacitors
  • Two drivers and two receivers
  • ±30V receiver input range
  • Low supply current: 8mA typical
  • Internal pull-up resistors on driver inputs

Applications

  • UART-to-RS-232 level conversion
  • PC serial port interfaces
  • Embedded system serial communication
  • Modem and terminal interfaces
  • Battery-powered RS-232 systems
Product Introduction: MAX232CPE Product Introduction

The MAX232CPE from Analog Devices (formerly Maxim Integrated) is the industry-standard dual RS-232 driver/receiver that converts between TTL/CMOS logic levels (0-5V) and RS-232 voltage levels (±5V to ±15V) using only a single 5V power supply. An internal dual charge pump generates approximately +10V and -10V from the 5V input using four external 1µF capacitors, eliminating the need for external ±12V supplies. Each device contains two drivers that invert TTL inputs to RS-232 outputs, and two receivers that invert RS-232 inputs to TTL outputs. The drivers guarantee ±5V minimum output swing under worst-case conditions (3kΩ load, 4.5V VCC), meeting TIA/EIA-232-F requirements. The receivers have 0.5V hysteresis for noise immunity and accept input voltages up to ±30V. The CPE suffix denotes the commercial temperature range (0°C to +70°C) in a PDIP-16 through-hole package. For lower-voltage applications, the MAX3232 operates from 3.0V to 5.5V.

Working Principle: MAX232CPE Working Principle

The MAX232CPE uses a dual charge-pump voltage converter to generate the ±10V rails needed for RS-232 driver outputs from a single 5V supply. The first charge pump uses capacitor C1 to double the 5V input to approximately +10V, stored on C3 at the V+ pin. The second charge pump uses capacitor C2 to invert the +10V to approximately -10V, stored on C4 at the V- pin. These generated voltages power the RS-232 driver output stages. Each driver is an inverting level shifter: a TTL LOW input (0V) produces an RS-232 HIGH output (+8V typical), and a TTL HIGH input (5V) produces an RS-232 LOW output (-8V typical). The inversion is by design—RS-232 defines a logic 1 (mark) as -3V to -15V and a logic 0 (space) as +3V to +15V, which is the opposite polarity of TTL. Each receiver inverts the RS-232 signal back to TTL levels: an RS-232 input above +2.4V produces a TTL LOW output, and an input below +0.8V produces a TTL HIGH output. The 0.5V hysteresis between these thresholds prevents oscillation on slow or noisy input edges. Internal 400kΩ pull-up resistors on the driver inputs ensure that unused drivers output an RS-232 LOW (mark) state, which is the idle condition for serial communication.

Pin Description: MAX232CPE Pin Definition and Functions
Pin Name Type Description
1 C1+ Capacitor Charge pump capacitor C1 positive terminal
2 V+ Power +10V generated output (charge pump)
3 C1- Capacitor Charge pump capacitor C1 negative terminal
4 C2+ Capacitor Charge pump capacitor C2 positive terminal
5 C2- Capacitor Charge pump capacitor C2 negative terminal
6 V- Power -10V generated output (charge pump)
7 T2OUT Output Driver 2 RS-232 output
8 R2IN Input Receiver 2 RS-232 input
9 R2OUT Output Receiver 2 TTL output
10 T2IN Input Driver 2 TTL input
11 T1IN Input Driver 1 TTL input
12 R1OUT Output Receiver 1 TTL output
13 R1IN Input Receiver 1 RS-232 input
14 T1OUT Output Driver 1 RS-232 output
15 GND Power Ground
16 VCC Power +5V supply
Application Scenarios: In which products and applications is MAX232CPE used
  • MCU Serial Port: T1IN/R1OUT connect to MCU UART TX/RX; T1OUT/R1IN connect to DB9 connector; 4×1µF caps for charge pump
  • PC Interface: MAX232 bridges 5V MCU to PC COM port via RS-232; 120kbps supports standard baud rates up to 115200
  • 3-Wire Serial: Uses 1 driver (TX) + 1 receiver (RX); remaining driver/receiver available for RTS/CTS flow control
  • Multi-Drop: Multiple MAX232 receivers on one RS-232 line; open RS-232 input defaults to HIGH on TTL output
  • Battery System: 8mA quiescent from 5V; can power-down MCU serial between transmissions for power savings
Alternative Models: What chips are recommended as replacements for MAX232CPE
Model Manufacturer Key Difference Package Specs
MAX3232ESE+T ADI 3.3V/5V dual-supply version with ±15kV ESD on RS-232 pins and 1µA auto-powerdown SOIC-16 250kbps/3-5.5V
ST3232EBPR ST 3-5.5V RS-232 transceiver with enhanced ESD and same 16-pin pinout for direct replacement TSSOP-16 250kbps/3-5.5V
SP3232EBCN-L/TR Silicon Labs 3.3V/5V equivalent with auto-powerdown and ±15kV ESD protection on bus pins DIP-16 250kbps/3-5.5V
TRS3232EIPWR TI 3-5.5V 2Tx/2Rs with ±15kV HBM ESD and 250kbps data rate in TSSOP-16 TSSOP-16 250kbps/3-5.5V
MAX3221CAE+T ADI 1Tx/1Rx single-channel version in SSOP-16 for applications needing only one serial port SSOP-16 1Mbps/1µA off

MAX232CPE is a 5V dual RS-232 driver/receiver in DIP-16 with 2Tx/2Rx and 120kbps data rate requiring four 1µF charge pump capacitors. MAX3232 operates at 3.3-5.5V with enhanced ESD and higher 250kbps rate. MAX3221 offers single-port 1Mbps with 1µA auto-powerdown. All are pin-compatible within their respective package families and use external charge pump capacitors for RS-232 voltage generation.

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1