Opens in a new tab

MCP23S17T-E/ML

16-bit SPI I/O expander, 10MHz, 25mA/pin, QFN-28, cascading up to 8 devices

1211

Effective Inventory

Image for reference only

Manufacturer Part:

MCP23S17T-E/ML

Package:

QFN-28 / VQFN-28 (6.0 x 6.0 x 0.9 mm, 0.65mm pitch, exposed pad)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The MCP23S17T-E/ML from Microchip Technology is a 16-bit I/O expander with SPI interface in a 28-pin QFN (6x6mm) package. It provides 16 bidirectional I/O pins with interrupt output, programmable via SPI at up to 10MHz. Three hardware address pins allow up to 8 devices on the same SPI bus.

Key Specifications

Interface SPI (Mode 0 and Mode 3)
Number of I/Os 16 (two 8-bit ports: PORTA and PORTB)
Max SPI Clock 10 MHz
Supply Voltage 1.8V to 5.5V
Output Current per Pin 25 mA sink/source
Quiescent Current 1 uA max (standby)
Operating Current 1 mA max @ SCK=1MHz
Interrupt Output INTA and INTB (configurable)
Address Pins 3 (A0, A1, A2 for up to 8 devices)
ESD Protection 4 kV HBM
Power Dissipation 700 mW
Operating Temperature -40 to 125 C
Package QFN-28 (6x6mm, exposed pad)

Features

  • 16-bit remote bidirectional I/O expansion
  • High-speed SPI interface up to 10MHz
  • 3 hardware address pins for cascading up to 8 devices
  • Two 16-bit configuration registers for I/O direction
  • Individual input polarity inversion
  • Interrupt-on-change from register defaults
  • Configurable interrupt output (active-high, active-low, open-drain)
  • INTA and INTB can be configured independently or mirrored
  • Power-on Reset (POR) circuit
  • Low standby current: 1uA max

Applications

  • Microcontroller I/O expansion via SPI
  • Keypad and matrix scanning
  • LCD interface expansion
  • LED control and status monitoring
  • Embedded system GPIO expansion
Product Introduction: MCP23S17T-E/ML Product Introduction

The MCP23S17T-E/ML from Microchip is a 16-bit SPI I/O expander in QFN-28 (6x6mm) package. Provides 16 bidirectional I/O pins with 25mA sink/source per pin and up to 10MHz SPI clock. Three address pins allow 8 devices on one bus. Features include interrupt-on-change, polarity inversion, POR, and 1uA standby current. The T suffix denotes tape-and-reel packaging, E denotes extended temperature range (-40 to 125C), and ML denotes QFN package.

Working Principle: MCP23S17T-E/ML Working Principle

The MCP23S17 is accessed via SPI (Mode 0 or Mode 3) using a standard SPI read/write protocol with an 8-bit opcode (device opcode + R/W bit) followed by a register address byte and data bytes. The 16 I/O pins are organized as two 8-bit ports (PORTA/GPA and PORTB/GPB), each with dedicated configuration registers for I/O direction (IODIRA/B), input polarity (IPOLA/B), interrupt-on-change control (GPINTENA/B), default comparison value (DEFVALA/B), and pull-up resistors (GPPUA/B). The interrupt output pins (INTA, INTB) can be configured to trigger on any pin change from a programmed default state, or on any change from the previous state (interrupt-on-change). The IOCON register configures global features like banking mode, interrupt mirroring, and open-drain interrupt output.

Pin Description: MCP23S17T-E/ML Pin Definition and Functions
Pin Name Type Function
1 GPB0 I/O Port B bit 0
2 GPB1 I/O Port B bit 1
3 GPB2 I/O Port B bit 2
4 GPB3 I/O Port B bit 3
5 GPB4 I/O Port B bit 4
6 GPB5 I/O Port B bit 5
7 GPB6 I/O Port B bit 6
8 GPB7 I/O Port B bit 7
9 VDD Power Positive supply (1.8-5.5V)
10 VSS Ground Ground
11 CS# Input SPI chip select (active low)
12 SCK Input SPI clock
13 SI Input SPI data in
14 SO Output SPI data out
15 A0 Input Hardware address bit 0
16 A1 Input Hardware address bit 1
17 A2 Input Hardware address bit 2
18 RESET# Input Reset (active low)
19 INTB Output Interrupt output for Port B
20 INTA Output Interrupt output for Port A
21-28 GPA0-GPA7 I/O Port A bits 0-7
Application Scenarios: In which products and applications is MCP23S17T-E/ML used
  • MCU GPIO expansion via SPI bus for keypad/matrix scanning
  • LCD module interface with limited MCU I/O pins
  • Industrial control panel with many switches and LEDs
  • Embedded system expansion board with 8 cascaded devices (128 I/O)
  • Robotics sensor/actuator interface
Alternative Models: What chips are recommended as replacements for MCP23S17T-E/ML
Manufacturer Part Number Package Notes
Microchip MCP23017T-E/ML QFN-28 I2C version of the same device
Microchip MCP23S17T-E/SS SSOP-28 SSOP package version
NXP PCAL6524 QFN-28 24-bit I2C I/O expander

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1