Opens in a new tab

NCL30160DR2G

1A hysteretic buck LED driver, 6.3-40V, SOIC-8, EOL

13477

Effective Inventory

Image for reference only

Manufacturer Part:

NCL30160DR2G

Package:

8-Pin SOIC (4.9 x 3.9 x 1.5 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The NCL30160DR2G is an onsemi 1.0A constant-current hysteretic buck LED driver with 6.3V-40V input, integrated 1A/50mOhm MOSFET, up to 1.4MHz switching, PWM dimming, and no loop compensation required. Packaged in SOIC-8, -40C to +125C. (Last Shipments / Discontinued)

Key Specifications

Input Voltage 6.3 V to 40 V
Output Current 1.0 A (LED current)
Integrated MOSFET 1.0A / 50 mOhm
Switching Frequency Up to 1.4 MHz
Topology Hysteretic buck, constant current
Dimming PWM via DIM/EN pin
Package SOIC-8

Features

  • Integrated 1.0A / 50mOhm MOSFET
  • 6.3V to 40V input voltage range
  • Up to 1.4MHz switching frequency
  • No control loop compensation required
  • Adjustable LED current via sense resistor
  • PWM dimming and enable via DIM/EN pin
  • Shorted LED shutdown protection
  • Thermal shutdown protection
  • 100% duty cycle capable

Applications

  • MR-16 LED lamp drivers
  • Automotive and general lighting
  • Industrial LED illumination
  • Constant current source for LEDs
Product Introduction: NCL30160DR2G Product Introduction

The NCL30160DR2G is an onsemi NFET hysteretic step-down constant-current LED driver in an SOIC-8 package. The device integrates a 1.0A / 50mOhm N-channel MOSFET and operates from 6.3V to 40V input, making it suitable for 12V/24V automotive and general lighting applications. The hysteretic control scheme provides excellent power supply rejection and fast response during load transients and PWM dimming, without requiring any control loop compensation. The LED current is set by a single external sense resistor from the CS pins to ground, with the hysteretic comparator maintaining the current within a programmed window. The dedicated DIM/EN pin enables wide-range PWM dimming by toggling the internal MOSFET on and off, and also serves as an enable/disable control. The switching frequency can be adjusted up to 1.4MHz via an external off-time setting resistor, allowing the use of small inductors and capacitors. Note: This product is in Last Shipments status and is being discontinued.

Working Principle: NCL30160DR2G Working Principle

The NCL30160DR2G uses a hysteretic (ripple-based) constant-current control scheme. The LED current flows through the external sense resistor (RSENSE) connected between the CS pins and ground. When the current through RSENSE exceeds the upper threshold (approximately 115mV/RSENSE), the internal MOSFET turns off and the inductor current freewheels through the external catch diode, decreasing through the LED string. When the sense voltage falls below the lower threshold (approximately 100mV/RSENSE), the MOSFET turns on again, ramping the inductor current up. The hysteresis window determines the LED current ripple, typically 15% peak-to-peak. The off-time is set by the ROT resistor connected from the ROT pin to VCC, which determines the switching frequency. The DIM/EN pin accepts a logic-level PWM signal for brightness control while maintaining the hysteretic current regulation during on-periods.

Pin Description: NCL30160DR2G Pin Definition and Functions
Pin Mnemonic Description
1,2 CS Current sense feedback (set LED current)
3 GND Ground
4 VCC Internal 5V regulator output
5 ROT Off-time setting resistor to VCC
6 DIM/EN PWM dimming and enable control
7 VIN Input supply (6.3-40V)
8 LX Internal MOSFET drain (switch node)
Application Scenarios: In which products and applications is NCL30160DR2G used
  • MR-16 12VAC LED lamp driver at 350mA with 1.4MHz for compact inductor
  • Automotive interior lighting at 700mA with PWM dimming from body controller
  • Industrial 24V LED string driver at 1A with shorted LED shutdown protection
  • General illumination constant current buck with capacitor-less output for cost reduction
Alternative Models: What chips are recommended as replacements for NCL30160DR2G
Model Manufacturer Key Difference
NCL30105DR2G onsemi 350mA version
AL8805WS-7 Diodes Inc 1A buck LED driver, similar
PT4115E89E CRMicro 1.2A buck LED driver
MP2480DN MPS 1A buck LED driver, SOIC-8

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1