Opens in a new tab

NCV8518BPDR2G

5V 250mA auto LDO, watchdog/wakeup/reset, SOIC-8 EP

3456

Effective Inventory

Image for reference only

Manufacturer Part:

NCV8518BPDR2G

Package:

SOIC-8 EP (4.9 x 3.9 x 1.5 mm, exposed pad)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The NCV8518BPDR2G from onsemi is an automotive AEC-qualified 5V low-dropout linear regulator with integrated watchdog, wakeup, reset, and enable functions in SOIC-8 EP package.

Key Specifications

Output Voltage 5.0V fixed (+/-2%)
Output Current 250 mA
Dropout Voltage 450 mV typical @ 150mA
Input Voltage Up to 45V (transient)
Quiescent Current 100 uA typical @ 250mA
Shutdown Current Less than 1 uA
Control Functions Enable, Watchdog, Wakeup, Reset
Protection Thermal shutdown, short circuit
AEC Qualified Yes
Package SOIC-8 EP (PDR2G suffix)
Operating Temperature -40 to +150 C (TJ)

Features

  • Integrated watchdog, wakeup, and reset for MCU control
  • 45V transient withstand for automotive battery environment
  • 100uA low quiescent current for always-on systems
  • Enable pin for logic-level shutdown control
  • AEC qualified for automotive applications

Applications

  • Automotive ECU 5V power supply
  • Tire pressure monitoring system MCU power
  • Battery-powered automotive electronics
  • Automotive body controller standby power
  • Industrial 5V logic supply with watchdog
Product Introduction: NCV8518BPDR2G Product Introduction

The NCV8518BPDR2G from onsemi is a precision micropower 5V low-dropout linear regulator with integrated microprocessor control functions including watchdog timer, wakeup output, reset output, and enable input. The device features 450mV typical dropout voltage at 150mA, 100uA typical quiescent current, and withstands 45V input transients for automotive environments. The watchdog and wakeup functions enable microprocessor sleep-mode management for reduced battery drain. The reset output is asserted during power-up, output undervoltage, or watchdog timeout. The NCV prefix indicates automotive qualification with AEC compliance and PPAP capability. The PDR2G suffix denotes SOIC-8 with exposed pad and tape and reel packaging.

Working Principle: NCV8518BPDR2G Working Principle

The NCV8518BPDR2G operates as an automotive LDO regulator with MCU supervisory functions. (1) The regulator uses a PNP pass transistor to achieve low dropout voltage (450mV typical at 150mA). The output voltage is set to 5.0V +/-2% by an internal bandgap reference and resistor divider. The 45V transient withstand is achieved through a high-voltage PNP pass element that can survive brief overvoltage events common in automotive battery systems. (2) The wakeup function generates a periodic square wave output from VOUT with 50% duty cycle at a frequency set by the external RDELAY resistor. This signal interrupts the MCU from sleep mode. The MCU responds with a falling-edge pulse on the WDI (watchdog input) pin. If the watchdog signal is not received within one wakeup period, the reset output is asserted. (3) The reset output is asserted low during four conditions: power-up (VOUT below regulation), output undervoltage, watchdog timeout, and input undervoltage. After the fault condition clears, the reset remains low for a delay period set by RDELAY, then goes high. The enable pin provides logic-level shutdown control with less than 1uA shutdown current.

Pin Description: NCV8518BPDR2G Pin Definition and Functions
Pin Name Function
1 DELAY Timing resistor for wakeup/reset
2 GND Ground
3 WDI Watchdog input from MCU
4 ENABLE Enable input (active high)
5 RESET Reset output (active low, CMOS)
6 WAKEUP Wakeup output to MCU
7 VIN Input supply voltage
8 VOUT 5V regulated output
EP GND Exposed pad (thermal/GND)
Application Scenarios: In which products and applications is NCV8518BPDR2G used
  • Automotive ECU 5V power supply with watchdog MCU supervision
  • Tire pressure monitoring system MCU power with wakeup function
  • Battery-powered automotive electronics with 100uA quiescent current
  • Automotive body controller standby power with enable shutdown
  • Industrial 5V logic supply with integrated watchdog and reset
Alternative Models: What chips are recommended as replacements for NCV8518BPDR2G
Model Manufacturer Key Difference
NCV8518CPDR2G onsemi Updated version, lower Iq
NCV8518BPWR2G onsemi Same, SOIC-16 WB package
TLF50251ELVXUMA1 Infineon 5V, 250mA, LDO, watchdog
TLE4274GV33 Infineon 3.3V, 200mA, auto LDO, reset
UA78M05IDCYR TI 5V, 500mA, no watchdog

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1