Opens in a new tab

PAM8302A

2.5W mono filterless Class-D audio amp, 2-5.5V, 90% efficiency, SOT-23-6

10041

Effective Inventory

Image for reference only

Manufacturer Part:

PAM8302A

Package:

SOT-23-6 (2.9 x 2.8 x 1.45mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The PAM8302A from Diodes Incorporated is a 2.5W mono Class-D audio power amplifier with high efficiency and low EMI. Operating from 2.0V to 5.5V, it requires no output filter in most applications and features a shutdown mode drawing less than 1uA in SOT-23-6 package.

Key Specifications

Output Power 2.5W at 5V into 4 Ohm (THD=10%)
Supply Voltage 2.0V to 5.5V
Efficiency Up to 90%
THD+N 0.2% at 1W, 1kHz, 5V, 8 Ohm
PSRR 75 dB at 1kHz
SNR 95 dB
Shutdown Current <1 uA
Output Type Filterless Class-D (BTL)
Operating Temperature -40 to 85 C
Package SOT-23-6

Features

  • Filterless Class-D architecture eliminates output LC filter
  • 2.5W output into 4 Ohm speaker at 5V
  • High 90% efficiency eliminates need for heatsink
  • Pop-and-click suppression circuitry

Applications

  • Portable Bluetooth speakers
  • Tablet and smartphone speaker amplifiers
  • Toy and novelty audio devices
  • LCD TV and monitor speakers
  • Intercom and PA systems
Product Introduction: PAM8302A Product Introduction

The PAM8302A from Diodes Incorporated is a 2.5W mono Class-D audio power amplifier that operates from a single 2.0V to 5.5V supply. Its filterless architecture eliminates the need for an external LC output filter in most applications, reducing BOM cost and board space. With up to 90% efficiency, the device requires no heatsink even at maximum output power. Pop-and-click suppression circuitry ensures clean power-on/off transitions. The SOT-23-6 package provides a compact footprint for space-constrained portable audio applications.

Working Principle: PAM8302A Working Principle

The PAM8302A employs a filterless Class-D PWM modulation scheme. **Modulation**: The analog input signal is compared against a high-frequency triangular waveform (typically 250kHz) to generate a PWM signal. The duty cycle of the PWM output is proportional to the instantaneous input voltage. **Output Stage**: A BTL (Bridge-Tied Load) H-bridge output drives the speaker differentially, doubling the voltage swing compared to single-ended amplifiers. The high-frequency PWM carrier is above the audible range and is filtered by the inherent inductance of the speaker coil. **Filterless Operation**: The speaker itself acts as a low-pass filter due to its inductive nature, recovering the audio signal from the PWM carrier. The remaining high-frequency energy is dissipated as heat in the speaker coil without audible effect. **EMI Management**: Spread-spectrum modulation or controlled slew rates minimize EMI emissions, allowing filterless operation to pass FCC/CE radiated emission limits with short speaker wires.

Pin Description: PAM8302A Pin Definition and Functions
Pin Name Description
1 IN+ Positive differential audio input
2 VDD Power supply (2.0V to 5.5V)
3 SD Shutdown control (high=active, low=shutdown)
4 OUT+ Positive BTL output to speaker
5 GND Ground
6 OUT- Negative BTL output to speaker
Application Scenarios: In which products and applications is PAM8302A used
  • Portable Speakers: Battery-powered Bluetooth speakers delivering 2.5W from a single Li-ion cell
  • Mobile Devices: Tablet and smartphone speaker boost amplifiers for improved audio output
  • Toy Audio: Sound effect amplifiers in electronic toys running from 2-3 AA batteries
  • DIY Audio: Compact audio amplifier modules for Arduino and Raspberry Pi projects
  • Intercom Systems: Voice output amplification in door phone and security intercom units
Alternative Models: What chips are recommended as replacements for PAM8302A
Model Manufacturer Key Difference
PAM8302AADCR Diodes Inc SOT-23-6, higher temp grade
MAX98306ETD+T Maxim Stereo, 3.7W, TQFN-16
TPA2005D1DRBR TI 1.4W, 2.5-5.5V, MSOP-8
NS4150 Nuvoton 3W, filterless, SOP-8
XPT8871 XinPu 2W, filterless, SOP-8, low cost

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1