Opens in a new tab

PC817C

1-ch optocoupler, phototransistor, CTR 200-400%, 5kVrms, DIP-4

15000

Effective Inventory

Image for reference only

Manufacturer Part:

PC817C

Package:

DIP-4 (6.4 x 4.58 x 3.5mm, 2.54mm pitch, through-hole)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The PC817C from Sharp (also produced by Everlight, Lite-on, and others) is a single-channel phototransistor optocoupler with 200-400% current transfer ratio, 5000Vrms isolation, and 80V collector-emitter voltage in a DIP-4 package.

Key Specifications

Channels 1 (single)
Output Type Phototransistor
CTR (Current Transfer Ratio) 200% to 400% @ IF=5mA, VCE=5V (C-grade)
Isolation Voltage 5000Vrms (AC 1 minute)
Collector-Emitter Voltage (VCEO) 35V min (80V typical from some mfrs)
Forward Voltage (VF) 1.2V typical, 1.4V max @ IF=20mA
Collector Dark Current (ICEO) 100nA max @ VCE=20V
VCE(sat) 0.1V typical, 0.2V max @ IF=20mA, IC=1mA
Forward Current (IF) 50mA max continuous
Collector Current (IC) 50mA max
Rise Time 4µs typical @ IC=2mA, RL=100Ω
Fall Time 3µs typical @ IC=2mA, RL=100Ω
Cut-off Frequency 80kHz typical (-3dB)
Total Power Dissipation 200mW
Operating Temperature -30°C to +100°C
Package DIP-4 (6.4 x 4.58 x 3.5mm)

Features

  • High CTR: 200-400% (C-grade) at 5mA
  • 5000Vrms isolation voltage
  • Compact DIP-4 package
  • UL recognized (E465130)
  • VDE approved (40039266)
  • Low VCE(sat): 0.1V typical
  • Multiple CTR grades available (A/B/C/D)

Applications

  • SMPS feedback loop isolation
  • Microcontroller I/O isolation
  • Signal isolation between logic domains
  • AC mains zero-crossing detection
  • Medical and industrial isolation
Product Introduction: PC817C Product Introduction

The PC817C from Sharp is a single-channel phototransistor optocoupler that provides galvanic isolation between input and output circuits using an infrared LED optically coupled to a phototransistor. The C-grade specifies a current transfer ratio (CTR) of 200% to 400% at IF=5mA, meaning the output phototransistor can sink up to 4× the LED current—a significant advantage over lower CTR grades when driving loads from small LED currents. The 5000Vrms isolation voltage provides robust safety isolation between high-voltage and low-voltage circuits, meeting IEC 60950 and medical equipment standards. The 80kHz cut-off frequency and 4µs/3µs rise/fall times make it suitable for low-frequency signal isolation but not for high-speed data communication. The PC817 is one of the most widely produced optocouplers, available from Sharp, Everlight, Lite-on, Cosmo, and many other manufacturers, ensuring multi-source availability. The C suffix denotes the CTR grade; A (50-160%), B (130-260%), and D (300-600%) grades are also available.

Working Principle: PC817C Working Principle

The PC817C consists of an infrared LED and an NPN phototransistor die, separated by a transparent insulating dielectric that provides 5000Vrms electrical isolation. When current flows through the LED (pins 1-2), it emits infrared light that passes through the dielectric and illuminates the base region of the phototransistor. The absorbed photons generate base current in the phototransistor, which is amplified by the transistor’s current gain (hFE) to produce a much larger collector current. The ratio of collector current to LED current is the current transfer ratio (CTR). For the PC817C, CTR = 200-400% at IF=5mA, meaning IC = CTR × IF = 200-400% × 5mA = 10-20mA. The phototransistor operates like a standard NPN transistor, but the base is optically driven rather than electrically connected. With no LED current, only a tiny dark current (100nA max) flows through the phototransistor. The VCE(sat) of 0.1V typical means the phototransistor can saturate like a normal transistor, pulling the collector very close to the emitter voltage when driven hard enough. The CTR degrades over time and with temperature: at 100°C, CTR may drop to 50% of its 25°C value, and after 50,000 hours of operation at IF=20mA, CTR may degrade by 30-50%. This aging must be factored into long-life designs such as SMPS feedback loops.

Pin Description: PC817C Pin Definition and Functions
Pin Name Type Description
1 Anode Input LED anode. Apply forward current (IF) through this pin to illuminate the internal infrared LED. Typical forward voltage VF = 1.2V at IF=20mA. Maximum continuous forward current is 60mA. Current-limiting resistor is required in series with the driving signal.
2 Cathode Input LED cathode. Connect to ground (or low-side driver) to complete the LED circuit. Reverse voltage rating is 6V maximum. In typical applications, the cathode is driven by a microcontroller GPIO through a current-limiting resistor (220-1kΩ for 5V systems).
3 Emitter Output Phototransistor emitter. Connects to ground or the low side of the output circuit. Collector current flows into Pin 4 and out of Pin 3 when the LED is illuminated. The CTR (Current Transfer Ratio) for PC817C grade is 200-400% at IF=5mA, VCE=5V.
4 Collector Output Phototransistor collector. Connects to the output pull-up resistor or load. Maximum collector-emitter voltage VCEO = 35V. Collector current is proportional to LED current multiplied by CTR. Dark current (LED off) is typically 50nA at VCE=20V.

PC817C pin assignment (DIP-4, top view, dot marks Pin 1): Pin 1 (top-left) = Anode, Pin 2 (top-right) = Cathode, Pin 3 (bottom-right) = Emitter, Pin 4 (bottom-left) = Collector. Pins 1-2 form the LED input side, Pins 3-4 form the phototransistor output side. The isolation barrier between sides provides 5000Vrms minimum insulation. CTR grade selection: A=80-160%, B=130-240%, C=200-400%, D=300-600%.

Application Scenarios: In which products and applications is PC817C used
  • SMPS Feedback: LED driven by TL431 via optocoupler; collector connects to PWM controller FB pin; 200% CTR provides ample loop gain
  • MCU I/O Isolation: LED from MCU GPIO through 330Ω resistor; collector pulled up to isolated 5V; emitter to isolated GND; signal crosses isolation barrier
  • Zero-Crossing: LED driven from AC mains through 100kΩ resistor and bridge rectifier; collector output pulses at 100/120Hz for TRIAC triggering
  • Relay Driver: LED from 3.3V MCU; collector drives relay coil through NPN transistor; 5kV isolation protects MCU from relay transients
  • Solid-State Relay: PC817C drives TRIAC gate through buffer transistor; optically isolated AC switching
Alternative Models: What chips are recommended as replacements for PC817C
Model Manufacturer Key Difference Package Specs
PC817A/B Sharp/Various Lower CTR grades (80-160%/130-240%) for general-purpose signal isolation applications DIP-4 50mA/35V
PC817D Sharp/Various Higher CTR grade (300-600%) for low-drive-current applications like TRIAC triggering DIP-4 50mA/35V
EL817C Everlight Direct pin-compatible equivalent with same CTR range and isolation voltage rating DIP-4 50mA/35V
TLP2710 Toshiba High-speed 5Mbps logic-output optocoupler with 5kV isolation for digital signal isolation SO6L 5Mbps/5kVrms
VO618A-3X017T Vishay High-CTR 100-200% phototransistor optocoupler with 5.3kVrms isolation for safety isolation SMD-4 50mA/5.3kVrms

PC817C is a 4-pin phototransistor optocoupler with 200-400% CTR (C-grade) and 5kVrms isolation. It is the most widely used optocoupler for feedback loops in switching power supplies and TRIAC triggering. A/B/D grades offer different CTR ranges. EL817 is a direct replacement. For high-speed digital isolation, TLP2710 provides 5Mbps logic output. For safety-critical applications, VO618A offers 5.3kVrms with high CTR.

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1