Opens in a new tab

PMA2-123LN+

Low noise amplifier, 12-13GHz, 28dB gain, SMA module

2991

Effective Inventory

Image for reference only

Manufacturer Part:

PMA2-123LN+

Package:

SMA Module (30.0 x 12.7 x 10.2 mm)

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

PMA2-123LN+ Overview

The PMA2-123LN+ is a low-noise MMIC amplifier from Mini-Circuits, frequency range 50MHz-12GHz, noise figure 2.6dB, gain 16dB, in a DFN-6 package, suitable for wideband receiver front-ends.

Key Features

  • Frequency range: 50MHz-12GHz
  • Gain: 16dB
  • Noise figure: 2.6dB
  • Output P1dB: +15dBm
  • Supply voltage: 5V
  • Supply current: 90mA
Product Introduction: PMA2-123LN+ Product Introduction

The PMA2-123LN+ is an ultra-wideband low-noise MMIC amplifier from Mini-Circuits, operating from 0.5 GHz to 12 GHz in a 2 mm x 2 mm, 8-lead MCLP package. It combines a low noise figure of 2.2 dB at 2 GHz and 2.6 dB at 8 GHz with high output IP3 of +28 dBm and flat gain of 17.6 dB with plus or minus 2.0 dB variation across the full bandwidth. Operating from a single 5 V or 6 V supply at 51 mA (5 V) or 68 mA (6 V), this GaAs pHEMT amplifier is internally matched to 50 Ohms and requires no external matching components.

Working Principle: PMA2-123LN+ Working Principle

The PMA2-123LN+ employs an enhancement-mode GaAs pHEMT process to implement a two-stage low-noise amplifier. The input stage is optimized for minimum noise figure while the output stage provides high linearity and output power. The RF input and output are both internally matched to 50 Ohms across the full 0.5-12 GHz bandwidth. The device operates from a single positive supply voltage applied through the RF output pin (drain bias) via an external bias tee or RF choke. The MMIC topology provides simultaneous low noise figure and high IP3 by biasing the pHEMT devices at optimal drain current. The 2 x 2 mm MCLP package provides low-inductance ground connections through the bottom paddle, essential for stable microwave operation up to 12 GHz.

Pin Description: PMA2-123LN+ Pin Definition and Functions
Pin Name Description
1 NC No connect
2 NC No connect
3 RF-IN RF input; 50 Ohm matched, AC coupled internally
4, 5 NC No connect
6 RF-OUT and DC-IN RF output; 50 Ohm matched. Also serves as VDD supply injection point
7, 8 NC No connect
Paddle GND Exposed ground paddle; solder to PCB ground plane

PMA2-123LN+ uses a 2x2mm 8-lead MCLP (QFN-style) package from Mini-Circuits with Pin 1 identified by a dot in the corner. The RF signal path is: Pin 3 = RF IN, Pin 6 = RF OUT + DC IN. All other pins (1,2,4,5,7,8) and the exposed paddle connect to GND. The RF OUT pin also serves as the DC supply input — an external RFC (radio frequency choke) or bias tee is required to inject 5V DC while blocking RF. Input and output are AC-coupled internally. The exposed paddle must be soldered to the PCB ground plane for both electrical ground return and thermal dissipation. Ground vias directly under the paddle improve RF performance at frequencies above 6GHz.

Application Scenarios: In which products and applications is PMA2-123LN+ used
  • Wideband Receiver Front-End: Low-noise amplification in S-band through X-band receiver chains for radar and communication
  • Satellite Communications: C-band and X-band LNA in VSAT and earth station downconverters
  • Test and Measurement: Broadband signal amplification in spectrum analyzers and network analyzers
  • Electronic Warfare: Wideband SIGINT and ELINT receiver front-end with high dynamic range
  • 5G Infrastructure: Sub-6 GHz and mmWave IF stage amplification in base station transceivers
Alternative Models: What chips are recommended as replacements for PMA2-123LN+
Model Manufacturer Freq NF Gain OIP3 Package
PMA2-123LNW+ Mini-Circuits 0.01-12 GHz 1.7 dB 19.6 dB +30 dBm QFN-6 (2×2)
PMA3-83LN+ Mini-Circuits 0.5-8 GHz 1.3 dB 22.1 dB +35 dBm QFN (3×3)
ZX60-123LN+ Mini-Circuits 0.5-12 GHz 2.4 dB 17 dB +28 dBm SMA
HMC519LC4 Analog Devices 6-18 GHz 2.5 dB 23 dB +26 dBm LC4
TQP3M9037 Qorvo 3-14 GHz 2.2 dB 18 dB +33 dBm QFN (3×3)

PMA2-123LN+ is a 0.5-12GHz MMIC LNA from Mini-Circuits in 2x2mm MCLP-8. The PMA2-153LN+ extends frequency to 15GHz with similar noise figure. PMA-545+ provides 50kHz-4GHz coverage with lower 0.75dB noise figure for sub-GHz applications. The PGA-103+ offers 0.05-6GHz with 23dB gain and higher +35dBm OIP3 for high-linearity receivers. The HMC519LC4 from ADI provides 24-34GHz low-noise amplification for millimeter-wave applications. All Mini-Circuits MCLP-8 amplifiers share the same 2x2mm footprint.

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1