Opens in a new tab

SN65HVD74DGKR

3.3V RS-485 transceiver, 1Mbps, VSSOP-8

4069

Effective Inventory

Image for reference only

Manufacturer Part:

SN65HVD74DGKR

Package:

VSSOP-8 (3.00 x 3.00 x 0.90 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

SN65HVD74DGKR Overview

The SN65HVD74DGKR is a 3.3V full-duplex RS-485 transceiver from Texas Instruments with data rates up to 20Mbps, built-in 12kV IEC ESD protection, in a VSSOP-8 package, suitable for industrial communication and motion control systems.

Key Features

  • Supply voltage: 3.3V
  • Data rate: 20Mbps
  • Full-duplex mode
  • 12kV IEC ESD protection
  • Bus voltage range: -7V to 12V
  • Operating temperature: -40C to 125C
Product Introduction: SN65HVD74DGKR Product Introduction

The SN65HVD74DGKR is a 3.3 V RS-485/RS-422 transceiver from Texas Instruments in an 8-pin VSSOP (3.0 x 3.0 mm) package, supporting data rates up to 20 Mbps with one driver and one receiver in full-duplex configuration. It features 1/8 unit load receiver input impedance allowing up to 256 nodes on the bus, plus or minus 16 kV IEC 61000-4-2 ESD protection on the bus pins, failsafe receiver operation (guaranteed high output for open/shorted inputs), and a low 370 uA receive-mode supply current. The extended -40 C to +85 C operating temperature range supports industrial environments.

Working Principle: SN65HVD74DGKR Working Principle

The SN65HVD74DGKR implements a full-duplex RS-485/RS-422 transceiver with separate driver and receiver signal paths. The driver section converts single-ended CMOS logic (applied to the D input) into a differential signal on the Y and Z outputs, compliant with TIA/EIA-485-A. The driver output stage provides a minimum 1.5 V differential output across a 54 Ohm load with current limiting and thermal shutdown protection against bus contention faults. The receiver section monitors the differential voltage between the A and B inputs and outputs the corresponding logic level on the R output. Receiver hysteresis (25 mV typical) provides noise immunity. Failsafe biasing ensures the receiver output goes high when the bus is open, shorted, or terminated but undriven, preventing random noise from being interpreted as data. The driver enable (DE) and receiver enable (RE) pins allow independent direction control. With DE low and RE high, the device enters a low-power shutdown mode. The 1/8 unit load receiver input impedance (greater than 96 kOhm) allows 256 transceivers to share a single RS-485 bus without exceeding the 32 unit-load maximum defined by the standard.

Pin Description: SN65HVD74DGKR Pin Definition and Functions
Pin Name Description
1 R Receiver output; logic level corresponding to A-B differential input
2 RE Receiver enable; active low, high-impedance R output when high
3 DE Driver enable; active high, high-impedance Y/Z outputs when low
4 D Driver input; CMOS logic level data input
5 GND Ground reference
6 Y Driver non-inverting output; connects to RS-485 bus
7 Z Driver inverting output; connects to RS-485 bus
8 VCC 3.3 V power supply (3.0 V to 3.6 V)

Package: VSSOP-8 (3.0 x 3.0 mm). Pin-compatible with industry-standard SN75176/SN65176 in SOIC-8 footprint with appropriate adapter.

Application Scenarios: In which products and applications is SN65HVD74DGKR used
  • Industrial RS-485 Networks: Multi-drop communication bus in factory automation supporting 256 nodes
  • Motor Drive Telemetry: Full-duplex RS-485 link between servo drive and motion controller at 20 Mbps
  • Building Automation: BACnet MS/TP and Modbus RTU communication over twisted-pair cabling
  • Grid Inverters: Isolated RS-485 communication between solar inverters and monitoring systems
  • Process Control: 4-20 mA loop digitizer communication over RS-485 in chemical and oil and gas plants
Alternative Models: What chips are recommended as replacements for SN65HVD74DGKR
Model Manufacturer Rate Supply Duplex Package
SN65HVD70DR Texas Instruments 1 Mbps 3.3 V Half SOIC-8
THVD1550DR Texas Instruments 50 Mbps 3.3 V Half SOIC-8
LTC2852IMS Analog Devices 20 Mbps 3.3 V Full MSOP-10
ADM3485EARZ Analog Devices 12 Mbps 3.3 V Half SOIC-8
ISL3179EIHZ Renesas 40 Mbps 3.3 V Full QSOP-16

SN65HVD74DGKR is a 3.3V 20Mbps RS-485 full-duplex transceiver from TI in VSSOP-8 (3x3mm) with ±30kV HBM ESD and ±12kV IEC ESD. The SN65HVD70DR provides half-duplex operation. SN65HVD75 offers 1Mbps lower-speed option. THVD1550 is the newer TI RS-485 family with up to 50Mbps data rates. For 5V operation, SN65HVD23 provides 25Mbps with ±16kV IEC ESD. ADM3483ARZ from ADI is a 3.3V half-duplex alternative with 12Mbps data rate.

Recommend Parts

IRFS4310ZTRLPBF

IRFS4310ZTRLPBF – 100V N-Channel HEXFET Power MOSFET, 7 mΩ RDS(on), D2PAK (TO-263AB)

Brand: infineon

Package: D2PAK (TO-263AB)

IN STOCK: 11137pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MSASJ105BB5475MFNA01

4.7uF 6.3V X5R MLCC, 0402, Taiyo Yuden

Brand: gigadevice

Package: 0402 (1005 Metric, 1.0 x 0.5 x 0.5 mm)

IN STOCK: 9701pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRF3415PBF

150V N-channel power MOSFET, 43A, 41mΩ RDS(on), TO-220AB package

Brand: infineon

Package: TO-220AB

IN STOCK: 2940pcs

Cargo cycle: 3-7 Days

The minimum order is 1

105017-1001

USB Type-C receptacle connector, 24-pin, SMD

Brand: Amphenol

Package: SMD (8.9 x 7.3 x 3.2 mm, right angle)

IN STOCK: 5335pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRLB3034PBF

IRLB3034PBF – 40V N-Channel StrongIRFET Power MOSFET (Logic Level), 1.7 mΩ (max) @ 10V; 2.0 mΩ @ 4.5V RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 9724pcs

Cargo cycle: 3-7 Days

The minimum order is 1

XC6SLX75-2FGG484I

Spartan-6 LX75 FPGA, 74637 logic cells, 132 DSP, 3096KB BRAM, 408 I/O, FBGA-484 23x23mm, -2 speed, industrial -40~100C, AMD Xilinx

Brand: xilinx

Package: FGG484 (484-ball fine-pitch BGA, 23x23mm body, 1.0mm ball pitch, 22×22 ball array, 6 I/O banks, lead-free)

IN STOCK: 890pcs

Cargo cycle: 3-7 Days

The minimum order is 1