Opens in a new tab

SN65HVD74DR

3.3V RS-485 half-duplex, 1Mbps, 256 nodes, 16kV ESD, SOIC-8

11000

Effective Inventory

Image for reference only

Manufacturer Part:

SN65HVD74DR

Package:

8-Pin SOIC (4.9 x 3.9 x 1.27 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The SN65HVD74DR is a Texas Instruments 3.3V RS-485 half-duplex transceiver with 1Mbps data rate, 1/8 unit load (256 nodes), fail-safe receiver, and 16kV HBM ESD on bus pins. It features receiver equalization for extended cable reach. Packaged in SOIC-8, -40C to +85C.

Key Specifications

Data Rate 1 Mbps
Supply 3.3 V
Mode Half-duplex
Unit Load 1/8 (256 nodes)
ESD (bus pins) 16 kV HBM
Package SOIC-8

Features

  • 3.3V single supply operation
  • 1Mbps data rate
  • 1/8 unit load, 256 nodes
  • Fail-safe receiver (open/short/idle)
  • 16kV HBM ESD on bus pins
  • Receiver equalization for cable reach
  • Half-duplex operation

Applications

  • Industrial RS-485 networks
  • Building automation (BACnet)
  • Motor drive communication
  • Utility metering networks
Product Introduction: SN65HVD74DR Product Introduction

The SN65HVD74DR is a Texas Instruments 3.3V RS-485 half-duplex transceiver optimized for reliable communication over long cables in industrial networks. The 1Mbps data rate supports high-speed Modbus and BACnet protocols. The 1/8 unit load specification allows up to 256 nodes on a single bus, exceeding the standard 32-node limit of full unit-load devices. The fail-safe receiver design guarantees a logic-high output when the bus is open, shorted, or idle, preventing false UART character detection. The receiver equalization feature extends cable reach by compensating for high-frequency signal attenuation on long cables, enabling reliable communication at 1Mbps over cable lengths that would otherwise require lower data rates. The 16kV HBM ESD protection on bus pins provides robust fault tolerance during hot-swap and field handling. The 3.3V supply eliminates the need for a 5V rail in 3.3V-only systems. Packaged in SOIC-8 rated for -40C to +85C.

Working Principle: SN65HVD74DR Working Principle

The SN65HVD74 uses differential signaling on the A and B bus pins for noise-immune communication over long cables. The driver converts single-ended logic (D input) into a differential voltage between A and B pins, with the driver enable (DE) controlling output activation. The receiver converts the differential bus voltage back to single-ended logic (R output), with the receiver enable (RE) controlling receiver activation. In half-duplex mode, DE and RE are typically controlled together (DE = RE-bar) for direction switching. The fail-safe receiver biases the A/B inputs so that an idle bus (no active driver) produces a differential voltage greater than -200mV, ensuring a logic-high on R. The receiver equalization adds a small amount of high-frequency boost to compensate for cable skin-effect attenuation, extending the usable cable length at 1Mbps. The 1/8 unit load is achieved by limiting the bus input leakage current to less than 125uA (1/8 of the 1mA full unit load standard).

Pin Description: SN65HVD74DR Pin Definition and Functions
Pin Mnemonic Description
1 R Receiver output
2 RE Receiver enable (active low)
3 DE Driver enable (active high)
4 D Driver input
5 GND Ground
6 A Bus pin A (non-inverting)
7 B Bus pin B (inverting)
8 VCC 3.3V supply
Application Scenarios: In which products and applications is SN65HVD74DR used
  • Industrial Modbus RS-485 network with 256 nodes and receiver equalization for long cables
  • Building automation BACnet MS/TP communication at 1Mbps
  • Motor drive inverter communication with 16kV ESD bus protection
  • Utility smart metering network with fail-safe receiver for open-bus detection
Alternative Models: What chips are recommended as replacements for SN65HVD74DR
Model Manufacturer Key Difference
SN65HVD75DR TI Full-duplex version
SN65HVD72DR TI No equalization, lower cost
THVD1450 TI 5V, higher speed
SP3485 Maxim Similar 3.3V RS-485

Recommend Parts

IRFS4310ZTRLPBF

IRFS4310ZTRLPBF – 100V N-Channel HEXFET Power MOSFET, 7 mΩ RDS(on), D2PAK (TO-263AB)

Brand: infineon

Package: D2PAK (TO-263AB)

IN STOCK: 11137pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MSASJ105BB5475MFNA01

4.7uF 6.3V X5R MLCC, 0402, Taiyo Yuden

Brand: gigadevice

Package: 0402 (1005 Metric, 1.0 x 0.5 x 0.5 mm)

IN STOCK: 9701pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRF3415PBF

150V N-channel power MOSFET, 43A, 41mΩ RDS(on), TO-220AB package

Brand: infineon

Package: TO-220AB

IN STOCK: 2940pcs

Cargo cycle: 3-7 Days

The minimum order is 1

105017-1001

USB Type-C receptacle connector, 24-pin, SMD

Brand: Amphenol

Package: SMD (8.9 x 7.3 x 3.2 mm, right angle)

IN STOCK: 5335pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRLB3034PBF

IRLB3034PBF – 40V N-Channel StrongIRFET Power MOSFET (Logic Level), 1.7 mΩ (max) @ 10V; 2.0 mΩ @ 4.5V RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 9724pcs

Cargo cycle: 3-7 Days

The minimum order is 1

XC6SLX75-2FGG484I

Spartan-6 LX75 FPGA, 74637 logic cells, 132 DSP, 3096KB BRAM, 408 I/O, FBGA-484 23x23mm, -2 speed, industrial -40~100C, AMD Xilinx

Brand: xilinx

Package: FGG484 (484-ball fine-pitch BGA, 23x23mm body, 1.0mm ball pitch, 22×22 ball array, 6 I/O banks, lead-free)

IN STOCK: 890pcs

Cargo cycle: 3-7 Days

The minimum order is 1