Opens in a new tab

SN74LS93N

4-bit binary ripple counter, ÷2+÷8 sections, LS TTL, PDIP-14

3000

Effective Inventory

Image for reference only

Manufacturer Part:

SN74LS93N

Package:

PDIP-14 (19.3 x 6.35 x 4.57mm, 2.54mm pitch, through-hole)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The SN74LS93N from Texas Instruments is a 4-bit binary ripple counter consisting of a divide-by-2 section and a divide-by-8 section — when externally connected, it counts 0-15 in a 14-pin PDIP package.

Key Specifications

Function 4-bit binary ripple counter
Logic Family LS (Low-power Schottky)
Supply Voltage 4.75V to 5.25V
Counter Sections Divide-by-2 (CP0/Q0) + Divide-by-8 (CP1/Q1,Q2,Q3)
Max Count 15 (4-bit binary, 0-15)
Trigger Negative edge (HIGH-to-LOW transition)
Reset Asynchronous, gated AND (MR1·MR2, active HIGH)
Max Clock Frequency 25MHz typical
Propagation Delay 70ns max @ 5V
Operating Temperature 0°C to +70°C
Package PDIP-14 (19.3 x 6.35mm)

Features

  • Two independent counter sections: ÷2 and ÷8
  • External connection Q0→CP1 creates ÷16 counter
  • Gated AND master reset (MR1 AND MR2 both HIGH = reset)
  • Negative-edge triggered
  • Typical power dissipation: 45mW

Applications

  • 4-bit binary counting (0-15)
  • Frequency division by 2, 4, 8, 16
  • Time-delay circuits
  • Event counting
Product Introduction: SN74LS93N Product Introduction

The SN74LS93N from Texas Instruments is a 4-bit binary ripple counter consisting of two independent sections: a divide-by-2 section (clocked by CP0, output Q0) and a divide-by-8 section (clocked by CP1, outputs Q1, Q2, Q3). The two sections are NOT internally connected — the designer must externally wire Q0 to CP1 to create a full 4-bit binary counter counting 0-15 with divide-by-2, 4, 8, and 16 outputs. This separation allows flexible configurations: using only the ÷2 section, only the ÷3/÷8 section, or both together. The negative-edge triggering (counting on the HIGH-to-LOW clock transition) is standard for the 74LS90/92/93 family. The gated AND master reset requires BOTH MR1 AND MR2 to be HIGH simultaneously to reset the counter; if either is LOW, counting continues. This allows one MR input to be used as an enable while the other provides the reset function. The 74LS93 is part of the 74LS90/92/93 family: LS90 is a decade (0-9) counter, LS92 is a divide-by-12 counter, and LS93 is a 4-bit binary (0-15) counter. The N suffix denotes the PDIP-14 through-hole package.

Working Principle: SN74LS93N Working Principle

The SN74LS93N contains four JK flip-flops configured as two independent counter sections. Section 1: A single flip-flop with clock input CP0 and output Q0. It toggles on the HIGH-to-LOW transition of CP0, dividing the input frequency by 2. Section 2: Three flip-flops cascaded as a 3-bit ripple counter with clock input CP1 and outputs Q1, Q2, Q3. CP1 drives the first flip-flop (Q1), Q1 drives the second (Q2), and Q2 drives the third (Q3). The count sequence on Q3,Q2,Q1 is: 000→001→010→011→100→101→110→111→000 (divide by 8). For 4-bit binary counting: connect Q0 to CP1 externally. Input pulses on CP0; Q0 toggles at half the input rate; Q0’s HIGH-to-LOW transitions clock the ÷8 section. The full count on Q3,Q2,Q1,Q0 is 0000→0001→…→1111→0000 (0-15). Reset: when MR1 AND MR2 are both HIGH, all four flip-flops are cleared (Q0-Q3 = LOW). If either MR is LOW, the counter operates normally. The counter is negative-edge triggered throughout.

Pin Description: SN74LS93N Pin Definition and Functions
Pin Name Type Description
1 CP1 Input Clock input for ÷8 section (negative edge)
2 MR1 Input Master reset 1 (active HIGH, AND-gated with MR2)
3 MR2 Input Master reset 2 (active HIGH, AND-gated with MR1)
4 NC — No connection
5 VCC Power Supply (5V)
6 MR1* Input Master reset 1 (duplicate, connect together)
7 MR2* Input Master reset 2 (duplicate, connect together)
8 Q2 Output Counter output bit 2
9 Q1 Output Counter output bit 1
10 Q3 Output Counter output bit 3 (MSB)
11 Q0 Output Counter output bit 0 (LSB, ÷2 section)
12 GND Power Ground
13 NC — No connection
14 CP0 Input Clock input for ÷2 section (negative edge)
Application Scenarios: In which products and applications is SN74LS93N used
  • 4-Bit Binary Counter (0-15): Q0 → CP1 (external wire); input pulses → CP0; MR1 and MR2 tied together; Q0-Q3 count 0-15; divide by 2,4,8,16
  • Independent ÷2 and ÷8: Two separate clocks: CP0 drives Q0 (÷2); CP1 drives Q1-Q3 (÷8); no external connection needed
  • Frequency Divider: CP0 input; Q0=÷2, Q1=÷4, Q2=÷8, Q3=÷16 (with Q0→CP1 connected)
  • Controlled Reset: MR1 tied HIGH; MR2 = enable signal; counter runs when MR2=LOW, resets when MR2=HIGH; one MR as gate, other as reset
Alternative Models: What chips are recommended as replacements for SN74LS93N
Model Manufacturer Key Difference Package Supply
74LS93N TI/Nexperia Original TTL version with 5V-only supply, typical propagation delay 10-15ns DIP-14 5V TTL
74LS93D TI/Nexperia Surface-mount SOIC version of LS with identical logic function SOIC-14 5V TTL
74HC93D TI/Nexperia CMOS version with wide 2-6V supply range, lower power consumption and higher noise immunity SOIC-14 2-6V CMOS
74HC93N TI/Nexperia Through-hole DIP version of HC family for prototyping and repair DIP-14 2-6V CMOS
74HCT93D TI/Nexperia CMOS with TTL-compatible input levels, ideal for mixing with LS devices at 5V SOIC-14 4.5-5.5V TTL-in
74HCT93N TI/Nexperia Through-hole DIP version of HCT family for prototyping and repair DIP-14 4.5-5.5V TTL-in

The 7493 is a 4-Bit Binary Ripple Counter. Family variants span from the original LS TTL (5V only) to modern LVC/AUP (down to 0.8V). HC and HCT versions offer 2-6V CMOS operation with HCT providing TTL-compatible input thresholds for mixed 5V systems. CD4000-series equivalents offer the widest 3-18V supply range at the cost of lower switching speed. DIP packages (N suffix) are through-hole; SOIC (D suffix) and TSSOP are surface-mount.

Recommend Parts

IRFS4310ZTRLPBF

IRFS4310ZTRLPBF – 100V N-Channel HEXFET Power MOSFET, 7 mΩ RDS(on), D2PAK (TO-263AB)

Brand: infineon

Package: D2PAK (TO-263AB)

IN STOCK: 11137pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MSASJ105BB5475MFNA01

4.7uF 6.3V X5R MLCC, 0402, Taiyo Yuden

Brand: gigadevice

Package: 0402 (1005 Metric, 1.0 x 0.5 x 0.5 mm)

IN STOCK: 9701pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRF3415PBF

150V N-channel power MOSFET, 43A, 41mΩ RDS(on), TO-220AB package

Brand: infineon

Package: TO-220AB

IN STOCK: 2940pcs

Cargo cycle: 3-7 Days

The minimum order is 1

105017-1001

USB Type-C receptacle connector, 24-pin, SMD

Brand: Amphenol

Package: SMD (8.9 x 7.3 x 3.2 mm, right angle)

IN STOCK: 5335pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRLB3034PBF

IRLB3034PBF – 40V N-Channel StrongIRFET Power MOSFET (Logic Level), 1.7 mΩ (max) @ 10V; 2.0 mΩ @ 4.5V RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 9724pcs

Cargo cycle: 3-7 Days

The minimum order is 1

XC6SLX75-2FGG484I

Spartan-6 LX75 FPGA, 74637 logic cells, 132 DSP, 3096KB BRAM, 408 I/O, FBGA-484 23x23mm, -2 speed, industrial -40~100C, AMD Xilinx

Brand: xilinx

Package: FGG484 (484-ball fine-pitch BGA, 23x23mm body, 1.0mm ball pitch, 22×22 ball array, 6 I/O banks, lead-free)

IN STOCK: 890pcs

Cargo cycle: 3-7 Days

The minimum order is 1