Opens in a new tab

TLE8104E

Quad low-side auto switch, SPI, 1A/ch, DSO-20

4567

Effective Inventory

Image for reference only

Manufacturer Part:

TLE8104E

Package:

DSO-20 (12.6 x 7.6 x 2.35 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The TLE8104E from Infineon Technologies is a quad low-side powertrain switch in Smart Power Technology (SPT) with SPI control and diagnosis, designed for automotive applications in DSO-20 package.

Key Specifications

Channels 4 low-side DMOS switches
Operating Voltage (VS) 4.5V to 5.5V
Drain-Source Voltage 45V to 60V (VDS(AZ))
RDS(ON) at 25C 320 mOhm typical
RDS(ON) at 150C 650 mOhm max
Nominal Load Current 1 A per channel
Current Limitation 3 A min per channel
Interface 8-bit SPI (control + diagnosis)
Protection Overload, overtemperature, overvoltage
Diagnosis Open load, short to GND, overtemp warning
AEC Qualified Yes
Package DSO-20
Operating Temperature -40 to +150 C (TJ)

Features

  • Four independent DMOS low-side switches with SPI control
  • Parallel input control for PWM applications (e.g. gasoline port injection)
  • Programmable active-high or active-low parallel inputs
  • Comprehensive protection: overload, overtemperature, overvoltage
  • Fault diagnosis via SPI or external FAULT pin

Applications

  • Automotive gasoline port injection control
  • Automotive relay and solenoid switching
  • Industrial 5V logic power switch array
  • Motor drive pre-driver with SPI diagnosis
  • Automotive body controller output stage
Product Introduction: TLE8104E Product Introduction

The TLE8104E from Infineon Technologies is a quad low-side switch in Smart Power Technology (SPT) designed for automotive powertrain applications. The device features four open-drain DMOS output stages with 320mOhm typical RDS(ON) at 25C, each rated for 1A nominal load current with 3A minimum current limitation. The output stages can be controlled directly by parallel inputs for PWM applications such as gasoline port injection, or by 8-bit SPI for diagnosis and control. The parallel inputs are programmable as active-high or active-low. Comprehensive protection includes overload, overtemperature, and overvoltage shutdown. Diagnosis is available via SPI status registers or the external FAULT pin. The device is AEC qualified for automotive use.

Working Principle: TLE8104E Working Principle

The TLE8104E operates as a quad low-side DMOS switch array. (1) Each of the four output channels consists of an N-channel DMOS transistor connected between the load (drain) and ground (source). When the channel is turned on, current flows from the battery through the load and through the DMOS transistor to ground. The 320mOhm RDS(ON) minimizes power dissipation at the nominal 1A load current. (2) The device can be controlled via two methods: parallel inputs (IN1-IN4) for direct PWM control, or 8-bit SPI interface for serial control and diagnosis. The PRG pin configures parallel inputs as active-high or active-low. The SPI provides readback of diagnostic information including overload flags, open-load detection, and overtemperature warning for each channel. (3) Protection circuits monitor each channel independently. Overload protection limits the current to 3-6A when a short circuit occurs. Overtemperature protection shuts down the affected channel when junction temperature exceeds 170-200C with 10K hysteresis. The overvoltage clamp protects the DMOS transistors from inductive kickback when switching off inductive loads.

Pin Description: TLE8104E Pin Definition and Functions
Pin Name Function
1-2 OUT1, OUT2 DMOS output drains (channels 1-2)
3-4 VS, GND 5V supply and ground
5 IN1 Parallel input channel 1
6 IN2 Parallel input channel 2
7 IN3 Parallel input channel 3
8 IN4 Parallel input channel 4
9 PRG Input polarity programming
10 RESET Reset input (active low)
11 CS SPI chip select
12 SCLK SPI clock
13 SI SPI serial data input
14 SO SPI serial data output
15 FAULT Fault diagnosis output
16-17 OUT3, OUT4 DMOS output drains (channels 3-4)
Application Scenarios: In which products and applications is TLE8104E used
  • Automotive gasoline port injection control with PWM parallel inputs
  • Automotive relay and solenoid switching with SPI diagnosis
  • Industrial 5V logic power switch array with overcurrent protection
  • Motor drive pre-driver with comprehensive SPI diagnostic readback
  • Automotive body controller output stage with fault detection
Alternative Models: What chips are recommended as replacements for TLE8104E
Model Manufacturer Key Difference
TLE8106E Infineon 6-channel version, same family
TLE6244GP Infineon 4-ch low-side, different package
MC33880 NXP 8-ch low-side, SPI, similar
L9349 ST 4-ch low-side, SPI diagnosis
BTN8982TA Infineon Half-bridge, higher current

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1