Opens in a new tab

TLE9261-3BQX

Mid-Range+ SBC, 1xCAN FD+PN, 3x LDO, 4x HS output, 15μA sleep, VQFN-48

0

Effective Inventory

Image for reference only

Manufacturer Part:

TLE9261-3BQX

Package:

VQFN-48 (7 x 7 x 0.9 mm) with LTI

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The TLE9261-3BQX is an Infineon OPTIREG™ Mid-Range+ System Basis Chip (SBC) with 1x CAN FD transceiver (with Partial Networking), 3 voltage regulators (5V/250mA, 5V/100mA, external PNP driver), 4 high-side outputs, and 16-bit SPI interface. Designed for automotive CAN-based body control and gateway modules with ultra-low 15μA sleep current.

Key Specifications

CAN Transceiver 1x CAN FD (ISO 11898-2:2016), up to 5Mbps, Partial Networking
VCC1 (Main LDO) 5V / 250mA
VCC2 (Sensor LDO) 5V / 100mA (off-board protected)
VCC3 (External PNP Driver) 5V or 3.3V / up to 400mA (with external PNP)
High-Side Outputs 4 x 150mA (7Ω typ.)
Sleep Mode Current 15μA (typical)
Stop Mode Current 44μA (typical)
Wake Sources CAN, Wake pins, Cyclic wake
Operating Temperature -40°C to +150°C
Qualification AEC-Q100

Features

  • OPTIREG™ Mid-Range+ SBC family (software compatible across TLE926x/TLE927x)
  • CAN FD with Partial Networking and FD tolerant mode
  • Three voltage regulators (2 internal LDO + 1 external PNP driver)
  • 4 high-side outputs with 7Ω typ. on-resistance
  • 2 configurable HV GPIOs (fail output, wake input, or switch)
  • 3 HV wake inputs with voltage level monitoring
  • Alternate HV measurement function for battery voltage sensing
  • Configurable timeout/window watchdog with reset
  • Cyclic wake and cyclic sense in low-power modes
  • Up to 3 fail outputs
  • 16-bit SPI for control and diagnostics
  • VQFN-48 (7x7mm) with LTI feature for AOI

Applications

  • Body control modules (BCM)
  • Door control modules
  • HVAC control modules
  • Light control modules
  • Automotive gateway with CAN Partial Networking
Product Introduction: TLE9261-3BQX Product Introduction

The TLE9261-3BQX is an Infineon OPTIREG™ Mid-Range+ System Basis Chip (SBC) integrating one CAN FD transceiver with Partial Networking, three voltage regulators (5V/250mA main LDO, 5V/100mA sensor LDO, and external PNP transistor driver), four 150mA high-side outputs, and a 16-bit SPI interface. With 15μA sleep mode current, configurable watchdog, cyclic wake/sense, and three HV wake inputs, it is designed for automotive body control, door, HVAC, and light control modules. Software compatible across the entire TLE926x and TLE927x SBC family.

Working Principle: TLE9261-3BQX Working Principle

The TLE9261-3BQX integrates power management, bus communication, and diagnostic functions into a single SBC. The main LDO (VCC1) provides 5V/250mA for MCU supply. The sensor LDO (VCC2) provides 5V/100mA with off-board short-circuit protection. The external PNP driver (VCC3) can operate in standalone mode (5V or 3.3V, current limited by external shunt resistor up to 350mA) or load-sharing mode with VCC1. The CAN FD transceiver supports up to 5Mbps with Partial Networking (selective wake via WUF pattern detection). The state machine manages SBC modes: Normal (all functions active), Stop (VCC1/VCC2 on, CAN monitoring, 44μA), Sleep (VCC1 off, CAN/LIN wake capable, 15μA), Restart (temporary wake from Sleep), and Fail-Safe (safe state). The 4 high-side outputs can drive LEDs, relays, or sensors. The configurable window/timeout watchdog ensures MCU health, and the SPI provides full diagnostic readback including over-temperature, short-circuit, and open-load flags.

Pin Description: TLE9261-3BQX Pin Definition and Functions
Pin Group Mnemonic Description
1-4 VIN/GND Battery supply and ground
5-8 CANH/CANL/TXD/RXD CAN bus and MCU interface
9-14 SPI 16-bit SPI (CSN, CLK, SDI, SDO)
15-18 VCC1/VCC2 LDO outputs
19-22 HS1-HS4 4 high-side switch outputs
23-28 WK1-WK3 3 HV wake inputs
29-32 FO1-FO3/RO Fail outputs and reset
33-48 VCC3/GPIO External PNP driver and GPIO pins
Application Scenarios: In which products and applications is TLE9261-3BQX used
  • Body control module (BCM) with CAN FD, 3 LDOs, and 4 high-side lamp/relay outputs
  • Door control module with CAN Partial Networking selective wake and sensor LDO
  • HVAC control with external PNP driver for 3.3V sensor supply and cyclic wake
  • Light control module with 4 high-side outputs and open/short load diagnostics
  • Automotive gateway with CAN PN wake from sleep at 15μA standby current
Alternative Models: What chips are recommended as replacements for TLE9261-3BQX
Model Manufacturer Key Difference
TLE9263-3BQX Infineon Same + 2x LIN transceivers
TLE9262-3BQX Infineon Same + 1x LIN transceiver
TLE9278BQX Infineon 4x CAN FD, SMPS buck, high-end SBC
TJA1145T NXP Single CAN SBC with Partial Networking
NCV7430 onsemi Single CAN/LIN SBC

Recommend Parts

TMP275AIDR

0.5C I2C temp sensor, 12-bit, 2.7-5.5V, alert output, 8-SOIC

Brand: TI

Package: 8-SOIC (4.90 x 3.91 x 1.50 mm)

IN STOCK: 3681pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IL485E

NVE IL485E IsoLoop isolated RS-485 transceiver, 2.5kVrms isolation, 35Mbps, 16-SOIC WB

Brand: nve

Package: SOIC-16 WB

IN STOCK: 5280pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFS4227TRLPBF

IRFS4227TRLPBF – 200V N-Channel HEXFET PDP Switch Power MOSFET, 26 mΩ RDS(on), D2PAK (TO-263)

Brand: infineon

Package: D2PAK (TO-263)

IN STOCK: 4334pcs

Cargo cycle: 3-7 Days

The minimum order is 1

CD4070BM96

Quad 2-input XOR gate, 3-18V CMOS, 65ns at 10V, SOIC-14

Brand: TI

Package: SOIC-14 (8.75 x 3.9 x 1.5mm)

IN STOCK: 4245pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AB1526

Bluetooth 5.0 Dual Mode Audio SoC, TWS, AAC, Dual-mic ENC, Integrated Charger, BGA

Brand: airoha

Package: BGA

IN STOCK: 25000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LP2980IM5-5.0

50mA micropower ultra-low-dropout regulator, 5V, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.1 mm)

IN STOCK: 2557pcs

Cargo cycle: 3-7 Days

The minimum order is 1