Opens in a new tab

TMC5160A-TA-T

Stepper driver, 3A, 256ustep, stealthChop, HTQFP-48

3800

Effective Inventory

Image for reference only

Manufacturer Part:

TMC5160A-TA-T

Package:

48-Pin HTQFP (9.0 x 9.0 x 1.0 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The TMC5160A-TA-T is an Analog Devices (Trinamic) stepper motor driver with integrated MOSFETs for 3A RMS, 256 microsteps, and SPI/UART interface. Features stallGuard2, coolStep, and stealthChop for silent and sensorless operation. Packaged in HTQFP-48, -40C to +125C.

Key Specifications

Motor Current 3 A RMS (4.2A peak)
Microsteps 256
Supply 5.5V to 40V
Interface SPI / UART
RDS(on) 290 mohm HS+LS
Package HTQFP-48

Features

  • Integrated N-channel MOSFETs
  • 3A RMS motor current
  • 256 microstep resolution
  • stealthChop2 silent operation
  • stallGuard2 sensorless stall
  • coolStep load-adaptive current
  • SPI and UART configuration

Applications

  • 3D printers and CNC
  • Robotics and automation
  • Textile and packaging
  • Medical and lab equipment
Product Introduction: TMC5160A-TA-T Product Introduction

The TMC5160A-TA-T is an Analog Devices (Trinamic) integrated stepper motor driver and controller in a 48-pin HTQFP package. The device combines a motion controller (ramp generator, position controller) with power driver MOSFETs (290mohm HS+LS total) for 3A RMS (4.2A peak) coil current at 5.5V to 40V supply. The 256 microstep resolution provides ultra-smooth motion for precision positioning applications. stealthChop2 spread-spectrum PWM chopper eliminates audible motor noise at low and medium speeds, producing virtually silent stepper motor operation. stallGuard2 provides sensorless mechanical load measurement and stall detection by monitoring the motor back-EMF, enabling sensorless homing and reference point detection. coolStep dynamically reduces motor current based on the mechanical load (measured by stallGuard2), saving up to 75% energy in partial-load conditions. The integrated motion controller generates trapezoidal and S-shaped velocity ramps in hardware, offloading the host MCU from real-time step generation. SPI and UART interfaces provide register configuration and motion command access. The -TA suffix indicates HTQFP-48, -T indicates tape-and-reel. Packaged in HTQFP-48 rated for -40C to +125C.

Working Principle: TMC5160A-TA-T Working Principle

The TMC5160A integrates a motion controller and two full H-bridge drivers with internal N-channel MOSFETs. The motion controller generates trapezoidal velocity profiles (AMAX acceleration, VMAX velocity, DMAX deceleration) in hardware. The position controller maintains the target position using a 32-bit step counter. The microstep controller divides each full step into 256 microsteps using internal sine/cosine lookup tables, generating smooth current waveforms for both coils. stealthChop2 uses voltage-mode PWM with spread-spectrum dithering at low speeds, eliminating the current regulation noise that causes audible motor whine. At higher speeds, the driver transitions to spreadCycle (classic current regulation) for high dynamic performance. stallGuard2 monitors the motor back-EMF during the off-time of each chopper cycle; when the motor is lightly loaded, the back-EMF is low and the current decays slowly, indicating no stall. When the motor stalls, back-EMF drops to zero and the current decay changes, triggering the stall detection threshold. coolStep reduces the run current proportionally to the stallGuard2 load measurement, maintaining just enough torque for the actual load.

Pin Description: TMC5160A-TA-T Pin Definition and Functions

48-pin HTQFP with key signals: EN (enable), CLK (external clock), CSN (SPI chip select), SCK (SPI clock), SDI/SDO (SPI data), SWSEL (UART/SPI select), SWDIO (UART data), BM1/BM2 (bus mode), AIN/AIP (coil A outputs), BIN/BIP (coil B outputs), VS (motor supply), VCC_IO (logic supply), GND. Refer to datasheet for complete 48-pin HTQFP mapping.

Application Scenarios: In which products and applications is TMC5160A-TA-T used
  • 3D printer and CNC stepper drive with stealthChop2 for silent operation and 256 microsteps
  • Robotics joint drive with stallGuard2 sensorless homing and coolStep energy saving
  • Textile and packaging machine with hardware motion controller for trapezoidal ramps
  • Medical and laboratory equipment with smooth microstep motion and SPI configuration
Alternative Models: What chips are recommended as replacements for TMC5160A-TA-T
Model Manufacturer Key Difference
TMC5160-TA-T ADI Without A, different feature
TMC2130 ADI External MOSFETs, 1A
TMC2209 ADI 2.8A, UART only
DRV8825 TI 2.5A, simpler, no silent

Recommend Parts

TMP275AIDR

0.5C I2C temp sensor, 12-bit, 2.7-5.5V, alert output, 8-SOIC

Brand: TI

Package: 8-SOIC (4.90 x 3.91 x 1.50 mm)

IN STOCK: 3681pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IL485E

NVE IL485E IsoLoop isolated RS-485 transceiver, 2.5kVrms isolation, 35Mbps, 16-SOIC WB

Brand: nve

Package: SOIC-16 WB

IN STOCK: 5280pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFS4227TRLPBF

IRFS4227TRLPBF – 200V N-Channel HEXFET PDP Switch Power MOSFET, 26 mΩ RDS(on), D2PAK (TO-263)

Brand: infineon

Package: D2PAK (TO-263)

IN STOCK: 4334pcs

Cargo cycle: 3-7 Days

The minimum order is 1

CD4070BM96

Quad 2-input XOR gate, 3-18V CMOS, 65ns at 10V, SOIC-14

Brand: TI

Package: SOIC-14 (8.75 x 3.9 x 1.5mm)

IN STOCK: 4245pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AB1526

Bluetooth 5.0 Dual Mode Audio SoC, TWS, AAC, Dual-mic ENC, Integrated Charger, BGA

Brand: airoha

Package: BGA

IN STOCK: 25000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LP2980IM5-5.0

50mA micropower ultra-low-dropout regulator, 5V, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.1 mm)

IN STOCK: 2557pcs

Cargo cycle: 3-7 Days

The minimum order is 1