Opens in a new tab

TMC5160A-TA-T

Stepper motor driver, 3A, 20-50V, StallGuard2, StealthChop, TQFP-48

3200

Effective Inventory

Image for reference only

Manufacturer Part:

TMC5160A-TA-T

Package:

48-TQFP (7.00 x 7.00 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The TMC5160A-TA-T is an Analog Devices (Trinamic) high-power stepper motor controller and driver IC with integrated motion controller. It supports 8-60V motor supply with external MOSFETs for up to 20A coil current, 256 microsteps, StealthChop2 silent operation, and SpreadCycle high-dynamics mode. Packaged in 48-pin TQFP (7×7 mm), -40C to +125C.

Key Specifications

Motor Supply 8 V to 60 V
Max Coil Current 20 A (external MOSFETs)
Microsteps Up to 256
Interfaces SPI, UART, STEP/DIR
Ramp Generator SixPoint with DcStep
Package TQFP-48 (7×7 mm)

Features

  • Integrated SixPoint motion controller
  • 256 microsteps with MicroPlyer interpolation
  • StealthChop2 for silent operation
  • SpreadCycle for high dynamics
  • StallGuard2 sensorless stall detection
  • CoolStep load-adaptive current (75% savings)
  • DcStep load-dependent speed control
  • Encoder interface and 2x reference switch

Applications

  • Robotics and industrial drives
  • 3D printers and CNC machines
  • Textile and packaging machines
  • Liquid handling and medical
Product Introduction: TMC5160A-TA-T Product Introduction

The Trinamic TMC5160A-TA-T is a high-power stepper motor driver and controller IC integrating a motion controller with a 3A stepper motor driver in a single 48-pin TQFP package. The device combines Trinamic’s renowned StealthChop2 ultra-silent motor driving with StallGuard2 sensorless homing and CoolStep adaptive current control, delivering the most feature-rich stepper motor driver available at this power level. The integrated motion controller offloads ramp generation and position management from the host MCU—the user simply writes the target position to a register via SPI, and the TMC5160A autonomously computes and executes the velocity and acceleration profile. The 20V to 50V supply range supports NEMA 17 and NEMA 23 stepper motors in industrial automation, CNC, 3D printing, and laboratory automation. The StealthChop2 technology eliminates audible motor noise by using a voltage-chopper mode that maintains sinusoidal current waveform at low speeds—motors run silently below 300 RPM. At higher speeds, the driver seamlessly transitions to SpreadCycle mode for maximum torque. StallGuard2 detects mechanical endstops without limit switches by monitoring the motor back-EMF, enabling sensorless homing that reduces BOM cost and wiring complexity. CoolStep dynamically reduces motor current based on the mechanical load, saving up to 75% energy and reducing motor heating. The 256 microstep resolution ensures extremely smooth rotation without vibration resonance.

Working Principle: TMC5160A-TA-T Working Principle

The TMC5160A uses an SPI interface for configuration and motion control. The internal motion controller generates trapezoidal or S-curve velocity profiles based on the target position, maximum velocity, and acceleration parameters written to internal registers. The velocity profile is converted into step pulses that drive the internal stepper driver state machine. The driver stage uses an 8-bit microstep table with 256 microsteps per full step, generating two 90-degree phase-shifted sinusoidal current waveforms for the A and B motor coils. StealthChop2 operates by regulating the coil current using a voltage-mode PWM technique—the driver measures the coil current, computes the required PWM duty cycle, and applies it without a traditional current-sense resistor comparator loop. This approach eliminates the current regulation chopper noise that causes audible whining in conventional drivers. At motor speeds above the StealthChop2 threshold (programmable), the driver transitions to SpreadCycle, a current-mode chopper that uses a sophisticated cycle-by-cycle current regulation with freewheeling phase for optimal high-speed torque. StallGuard2 works by measuring the difference between the coil current and the expected current during the active chopper phase—when the motor hits a mechanical obstruction, the back-EMF drops, causing a detectable change in the current regulation behavior. CoolStep uses the StallGuard signal as a proxy for mechanical load and reduces the coil current proportionally when the load is below the full-load threshold.

Pin Description: TMC5160A-TA-T Pin Definition and Functions
Pin Mnemonic Description
1-2 BMA/BMB Motor phase B outputs (low-side)
3-4 BMH/BML Motor phase B outputs (high/low side)
5-6 AMA/AMB Motor phase A outputs (low-side)
7-8 AMH/AML Motor phase A outputs (high/low side)
9-10 VSA/VSB Bridge supply A/B (20-50V)
11-14 SR1/SR2 Sense resistor connections
15 EN Enable input (active low)
16 STEP Step pulse input (external step mode)
17 DIR Direction input
18-20 SDI/SDO/SCK SPI data and clock
21 CSN SPI chip select (active low)
22 CLK External clock input (optional)
23 DRV_ENN Driver enable (active low)
24 DIAG0 Diagnostic output 0 (StallGuard)
25 DIAG1 Diagnostic output 1 (overtemp/short)
26-28 VCC/5VOUT/GND Logic supply and ground
29-48 Misc Remaining power, ground, and NC pins
Application Scenarios: In which products and applications is TMC5160A-TA-T used
  • 3D printer stepper driver with StealthChop2 eliminating audible whining during printing, StallGuard2 for sensorless XY homing, and 256 microstep resolution for artifact-free surface finish
  • CNC machine axis drive with integrated motion controller offloading trapezoidal ramp generation from the host MCU via SPI position commands
  • Laboratory automation rotary stage with CoolStep adaptive current reducing motor heating by 75% during idle and low-load positioning
  • Industrial pick-and-place robot with SpreadCycle mode delivering maximum torque at 2000 RPM and StallGuard2 detecting mechanical collisions without limit switches
Alternative Models: What chips are recommended as replacements for TMC5160A-TA-T
Model Manufacturer Key Difference
TMC5160-BOB Trinamic Breakout board version with same IC
TMC2130 Trinamic 1.2A, 5-46V, external MOSFET driver only, QFN-28
DRV8825 TI 2.5A, 8.2-45V, 1/32 microstep, no silent mode
A4988 Allegro 2A, 8-35V, 1/16 microstep, basic driver only

Recommend Parts

TMP275AIDR

0.5C I2C temp sensor, 12-bit, 2.7-5.5V, alert output, 8-SOIC

Brand: TI

Package: 8-SOIC (4.90 x 3.91 x 1.50 mm)

IN STOCK: 3681pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IL485E

NVE IL485E IsoLoop isolated RS-485 transceiver, 2.5kVrms isolation, 35Mbps, 16-SOIC WB

Brand: nve

Package: SOIC-16 WB

IN STOCK: 5280pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFS4227TRLPBF

IRFS4227TRLPBF – 200V N-Channel HEXFET PDP Switch Power MOSFET, 26 mΩ RDS(on), D2PAK (TO-263)

Brand: infineon

Package: D2PAK (TO-263)

IN STOCK: 4334pcs

Cargo cycle: 3-7 Days

The minimum order is 1

CD4070BM96

Quad 2-input XOR gate, 3-18V CMOS, 65ns at 10V, SOIC-14

Brand: TI

Package: SOIC-14 (8.75 x 3.9 x 1.5mm)

IN STOCK: 4245pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AB1526

Bluetooth 5.0 Dual Mode Audio SoC, TWS, AAC, Dual-mic ENC, Integrated Charger, BGA

Brand: airoha

Package: BGA

IN STOCK: 25000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LP2980IM5-5.0

50mA micropower ultra-low-dropout regulator, 5V, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.1 mm)

IN STOCK: 2557pcs

Cargo cycle: 3-7 Days

The minimum order is 1