Opens in a new tab

TPS7A4001DGNR

Negative LDO, -20V, 1A, 16uVrms, 40dB PSRR, MSOP-8

3100

Effective Inventory

Image for reference only

Manufacturer Part:

TPS7A4001DGNR

Package:

8-Pin MSOP PowerPAD (3.0 x 3.0 x 1.0 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The TPS7A4001DGNR is a Texas Instruments -20V negative LDO with 1A output, 40dB PSRR at 1kHz, and 16uVrms noise. Ultra-low noise negative regulator for sensitive analog loads. Packaged in MSOP-8 PowerPAD, -40C to +125C.

Key Specifications

Output -0.5V to -20V adjustable
Current 1 A
PSRR 40 dB @ 1kHz
Noise 16 uVrms (10Hz-100kHz)
Dropout 200 mV @ 1A
Package MSOP-8 PowerPAD

Features

  • Negative voltage LDO, -0.5V to -20V
  • 1A output current
  • 16uVrms ultra-low noise
  • 40dB PSRR at 1kHz
  • 200mV dropout at 1A
  • NR pin for noise reduction
  • MSOP-8 PowerPAD package

Applications

  • Negative analog rail cleanup
  • Op amp and ADC negative supply
  • RF and VCO negative bias
  • Test and measurement
Product Introduction: TPS7A4001DGNR Product Introduction

The TPS7A4001DGNR is a Texas Instruments 1A negative-voltage low-dropout regulator in an 8-pin MSOP PowerPAD package. The device regulates negative input voltages from -0.5V to -20V, making it the negative-rail complement to the TPS7A45 positive LDO. The 16uVrms output noise over 10Hz to 100kHz and 40dB PSRR at 1kHz make it ideal for cleaning switching DC-DC negative rail noise for precision op amps, ADCs, and DACs that require a clean negative supply. The 200mV dropout at 1A provides good efficiency with moderate headroom. The NR (noise reduction) pin accepts an external 0.01uF capacitor that filters the internal reference noise, achieving the 16uVrms specification. The adjustable output voltage is set by two external resistors from VOUT to FB to GND, with a -1V reference. An EN (enable) pin allows shutdown with 1uA IQ. The MSOP-8 PowerPAD package provides low thermal resistance for 1A operation at higher input-output differentials. The device is stable with ceramic output capacitors (2.2uF minimum). Packaged in MSOP-8 PowerPAD rated for -40C to +125C.

Working Principle: TPS7A4001DGNR Working Principle

The TPS7A40 uses a PMOS pass transistor for low dropout on the negative rail. The error amplifier compares the FB pin voltage (derived from the output through the external resistor divider) with the -1V internal reference, driving the PMOS gate to maintain regulation. The NMOS architecture (similar to positive TPS7A45) provides low output noise and high PSRR inherent to the source-follower output topology. An internal charge pump generates the gate drive voltage required to fully enhance the PMOS pass transistor. The NR pin capacitor creates a low-pass filter that attenuates reference noise, achieving the 16uVrms output noise specification. When the EN pin is pulled low, the pass transistor is disabled and the output floats. Current limit and thermal shutdown protect the device during fault conditions. The device uses the negative rail as the reference domain, so all pin voltages are measured relative to the negative input supply.

Pin Description: TPS7A4001DGNR Pin Definition and Functions
Pin Mnemonic Description
1 OUT Regulated negative output
2 NR Noise reduction (0.01uF cap)
3 EN Enable (active high)
4 GND Ground (reference)
5 FB Feedback (-1V reference)
6 NC No connect
7 IN Negative input supply
8 NC No connect
Application Scenarios: In which products and applications is TPS7A4001DGNR used
  • Cleanup of DC-DC negative rail for precision dual-supply op amp with 16uVrms noise
  • Negative ADC/DAC reference supply with 40dB PSRR for switching converter cleanup
  • RF and VCO negative bias supply with NR pin capacitor for ultra-low noise
  • Test and measurement negative rail with MSOP-8 PowerPAD thermal performance
Alternative Models: What chips are recommended as replacements for TPS7A4001DGNR
Model Manufacturer Key Difference
TPS7A3301 TI -36V, lower current
TPS7A45 TI Positive LDO complement
LT3094 ADI Negative 500mA LDO
ADM7150-NEG ADI Negative LDO variant

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1