Opens in a new tab

TPS7A8801RTJT

Ultra-Low-Noise LDO, 1A, 0.8uVrms, 72dB PSRR, QFN-12

2345

Effective Inventory

Image for reference only

Manufacturer Part:

TPS7A8801RTJT

Package:

QFN-12 (3.5 x 3.5 x 1.0 mm, exposed pad)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The TPS7A8801RTJT from Texas Instruments is an ultra-low-noise LDO regulator with 1A output, 0.8uVrms noise, and 1.4V to 6.5V input in a QFN-12 package.

Key Specifications

Type Ultra-Low-Noise LDO Linear Regulator
Input Voltage 1.4 V to 6.5 V
Output Voltage Adjustable (0.8V to 5.0V)
Output Current 1 A
Output Noise 0.8 uVrms (10Hz to 100kHz, VOUT=1.8V)
PSRR 72 dB @ 1kHz
Dropout Voltage 120 mV @ 1A
Accuracy +/-1% over line, load, temperature
Quiescent Current 1.3 mA (typical)
Package QFN-12 (3.5 x 3.5 x 1.0 mm, RTJ suffix)
Operating Temperature -40C to +125C

Features

  • 0.8 uVrms ultra-low output noise
  • 72 dB PSRR at 1 kHz
  • 1A output current with 120 mV dropout
  • +/-1% output accuracy
  • Adjustable output from 0.8V to 5.0V
  • NR/SS pin for soft-start and noise reduction

Applications

  • RF and PLL power supply
  • High-speed ADC/DAC reference
  • Camera sensor power
  • Test and measurement equipment
Product Introduction: TPS7A8801RTJT Product Introduction

The TPS7A8801RTJT from Texas Instruments is an ultra-low-noise, high-PSRR LDO linear regulator designed for noise-sensitive applications such as RF transceivers, high-speed data converters, and precision analog circuits. The 0.8 uVrms output noise from 10 Hz to 100 kHz is among the lowest available, ensuring minimal phase noise contribution to VCOs and PLLs. The 72 dB PSRR at 1 kHz effectively rejects input supply ripple, reducing the need for pre-filtering. The 1A output current supports moderate-power loads including FPGA I/O banks and processor cores. The 120 mV dropout voltage at 1A allows efficient regulation from low headroom supplies. The NR/SS (Noise Reduction / Soft Start) pin connects an external capacitor that filters the internal bandgap reference noise and provides a controlled output voltage ramp. The QFN-12 package with exposed pad provides excellent thermal performance.

Working Principle: TPS7A8801RTJT Working Principle

The TPS7A8801 uses a PMOS pass transistor in a source-follower (common-drain) configuration. The error amplifier compares the feedback voltage (FB pin) with an internal 0.8V bandgap reference, driving the PMOS gate to regulate the output. The ultra-low noise is achieved through three techniques: (1) a low-noise bandgap reference filtered by the external NR capacitor (the dominant noise source in most LDOs), (2) a low-noise error amplifier design with chopper stabilization or auto-zeroing, and (3) a carefully optimized output stage that minimizes flicker noise contribution. The 72 dB PSRR is primarily determined by the error amplifier’s open-loop gain at low frequencies. At higher frequencies (>100 kHz), the PSRR rolls off as the amplifier bandwidth is exceeded, but the output capacitor’s impedance helps maintain some rejection. The 120 mV dropout at 1A is set by the PMOS on-resistance (Ron = 120 mOhm). The soft-start function uses the NR capacitor to slowly ramp the reference voltage, limiting inrush current.

Pin Description: TPS7A8801RTJT Pin Definition and Functions
Pin Name Type Function
1 OUT Output Regulated output voltage
2 OUT Output Regulated output voltage
3 NR/SS Analog Noise reduction capacitor / Soft-start
4 FB Input Feedback voltage (0.8V reference)
5 EN Input Enable (HIGH=on)
6 PG Output Power good indicator (open-drain)
7 BIAS Power Bias supply for internal circuitry
8 GND Power Ground
9 IN Power Input supply (1.4-6.5V)
10 IN Power Input supply (1.4-6.5V)
11-12 GND/Pad Power Ground / Exposed thermal pad
Application Scenarios: In which products and applications is TPS7A8801RTJT used
  • RF transceiver 1.8V VCO supply with 0.8uVrms noise for minimal phase noise
  • 16-bit ADC reference buffer LDO with 72dB PSRR from switching pre-regulator
  • High-speed SERDES PHY power with 0.8V output at 1A from 1.2V input
  • Precision instrument analog rail with NR capacitor for <1uVrms noise floor
Alternative Models: What chips are recommended as replacements for TPS7A8801RTJT
Manufacturer Part Number Package Notes
TI TPS7A8800RTJT QFN-12 Dual channel version
TI TPS7A7001RGW QFN-20 3A, higher current, similar noise
ADI LT3042EMSE MSOP-10 0.8uVrms, 200mA, similar noise class
ADI LT3045IVSE MSOP-10 0.8uVrms, 500mA
TI TPS7A4700RGWR QFN-20 1A, 3.8uVrms, lower cost

Recommend Parts

BC857BS

Dual PNP transistor, -45V, -100mA, SOT363, Nexperia

Brand: NXP

Package: SOT363 (SC-88, 2.1 x 1.25 x 0.95 mm)

IN STOCK: 8813pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM1200ARZ-RL7

Dual-channel digital isolator based on ADI iCoupler technology, 2/0 direction, SOIC-8 narrow body, 1Mbps (A grade), 2.7-5.5V dual supply, 2500Vrms isolation, >25kV/us CMTI, -40C to +105C.

Package: SOIC-8 Narrow (5.06 x 3.99 x 1.75mm)

IN STOCK: 12476pcs

Cargo cycle: 3-7 Days

The minimum order is 1

PIC32MX795F512L-80I/PT

MIPS32 MCU, 80MHz, 512KB Flash, Ethernet, dual CAN, USB OTG, 100-TQFP

Brand: MICROCHIP

Package: 100-TQFP (14.0 x 14.0 x 1.0 mm)

IN STOCK: 5670pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IS61WV25616BLL-10TLI

4Mbit async SRAM, 256Kx16, 10ns, 3.3V, 44-TSOP-II Industrial

Brand: Issi

Package: 44-TSOP II

IN STOCK: 7802pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AT45DB081E-SHN-T

8Mbit DataFlash, dual-SPI 85MHz, 2x264B SRAM buffers, USON-8 (4x3mm), page-based ECC

Brand: Renesas

Package: USON-8 (4 x 3 x 0.6mm, 0.8mm pitch)

IN STOCK: 4500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TIP35C

NPN power transistor, 100V VCEO, 25A Ic, 125W, TO-247, low saturation voltage, STMicroelectronics

Brand: ST

Package: TO-247 (through-hole, 3-pin)

IN STOCK: 11500pcs

Cargo cycle: 3-7 Days

The minimum order is 1