Opens in a new tab

TPS82084SILT

2A micro-module buck converter, integrated inductor, BGA-9, 2.4V-5.5Vin

13627

Effective Inventory

Image for reference only

Manufacturer Part:

TPS82084SILT

Package:

BGA-9 (2.80 x 3.00 x 1.20 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The TPS82084SILT from Texas Instruments is a 2.4-5.5V input, 2A micro-module step-down converter with integrated inductor in a BGA-9 package. Operating at 2.4 MHz with up to 95% efficiency, it provides the smallest complete DC-DC solution for space-constrained applications.

Key Specifications

Input Voltage 2.4 V to 5.5 V
Output Voltage 0.8 V to VDD (adjustable)
Output Current 2 A
Switching Frequency 2.4 MHz
Efficiency Up to 95%
Package BGA-9 (2.8 x 3.0 x 1.2 mm)

Features

  • Integrated inductor for smallest total solution size
  • Only two external components (input and output capacitors)
  • 2.4 MHz operation enables tiny ceramic capacitors
  • Power-save mode for high light-load efficiency
  • Output voltage tracking and soft-start
  • Overcurrent and thermal protection

Applications

  • Point-of-load conversion in portable devices
  • Space-constrained POL regulation
  • Battery-powered equipment
  • FPGA and processor core supply
  • Industrial distributed power
Product Introduction: TPS82084SILT Product Introduction

The TPS82084SILT from Texas Instruments is a 2 A micro-module DC-DC step-down converter in an ultra-compact 2.8 x 3.0 x 1.2 mm BGA-9 package with an integrated 0.47 µH inductor. The device accepts 2.4 V to 5.5 V input and provides an adjustable output from 0.8 V to VDD at up to 2 A. By integrating the inductor and requiring only two external ceramic capacitors, the TPS82084 delivers the smallest complete DC-DC solution footprint available. The 2.4 MHz switching frequency supports the use of small multi-layer ceramic capacitors while maintaining high efficiency up to 95%. The device automatically transitions between PWM mode for heavy loads and power-save mode (PFM) for light loads, maintaining high efficiency across the full load range. The output voltage soft-start prevents inrush current, and overcurrent and thermal shutdown protections ensure robust operation.

Working Principle: TPS82084SILT Working Principle

The TPS82084SILT is a synchronous buck converter with integrated MOSFET switches and a 0.47 µH chip inductor inside the BGA-9 package. The current-mode control loop modulates the high-side switch duty cycle to regulate the output voltage. At moderate to heavy loads, the device operates in fixed-frequency PWM mode at 2.4 MHz. At light loads, it enters power-save mode where switching pulses are skipped to reduce switching losses and maintain high efficiency. The integrated inductor eliminates the need for external inductor selection and layout optimization, simplifying design and ensuring reliable operation. The internal compensation is optimized for the integrated inductor value, eliminating external compensation components. The soft-start circuit ramps the output voltage gradually to limit inrush current.

Pin Description: TPS82084SILT Pin Definition and Functions
Pin Name Function
A1 VIN Input supply voltage (2.4 V to 5.5 V)
A2 VIN Input supply (parallel with A1)
A3 EN Enable input; high = enabled, low = shutdown
B1 GND Power ground
B2 GND Power ground
B3 FB Feedback input; connect resistor divider from VOUT
C1 VOUT Regulated output voltage
C2 VOUT Regulated output (parallel with C1)
C3 PG Power-good open-drain output
Application Scenarios: In which products and applications is TPS82084SILT used
  • Portable Device POL: Converting 3.3 V or 5 V rail to 1.2 V or 1.8 V core voltage in smartphones and tablets with minimal board area
  • FPGA Core Supply: Low-voltage high-current core supply for small-form-factor FPGA and CPLD designs
  • Wearable Electronics: Compact DC-DC conversion in smartwatches and fitness trackers with tight space constraints
  • Industrial Sensor Nodes: POL regulation from 3.3 V or 5 V in wireless sensor modules with limited PCB area
  • Battery-Powered Instruments: High-efficiency step-down from single-cell Li-ion for handheld measurement devices
Alternative Models: What chips are recommended as replacements for TPS82084SILT
Model Manufacturer VIN IOUT Inductor Package Notes
TPS82085SILT TI 2.4-5.5 V 2 A Integrated BGA-9 Different VOUT range
TPS82671SISR TI 2.3-5.5 V 1 A Integrated BGA-9 Lower current version
LMZ21701SILR TI 2.7-5.5 V 1 A Integrated BGA-9 Older generation, 1A
TPS62290TDRVRQ1 TI 2.25-6 V 1.5 A External SON-6 Requires external inductor
BD70522GUL-E2 Rohm 2.5-5.5 V 0.5 A External VCSP-8 Lower current, external L

Recommend Parts

TMP275AIDR

0.5C I2C temp sensor, 12-bit, 2.7-5.5V, alert output, 8-SOIC

Brand: TI

Package: 8-SOIC (4.90 x 3.91 x 1.50 mm)

IN STOCK: 3681pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IL485E

NVE IL485E IsoLoop isolated RS-485 transceiver, 2.5kVrms isolation, 35Mbps, 16-SOIC WB

Brand: nve

Package: SOIC-16 WB

IN STOCK: 5280pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFS4227TRLPBF

IRFS4227TRLPBF – 200V N-Channel HEXFET PDP Switch Power MOSFET, 26 mΩ RDS(on), D2PAK (TO-263)

Brand: infineon

Package: D2PAK (TO-263)

IN STOCK: 4334pcs

Cargo cycle: 3-7 Days

The minimum order is 1

CD4070BM96

Quad 2-input XOR gate, 3-18V CMOS, 65ns at 10V, SOIC-14

Brand: TI

Package: SOIC-14 (8.75 x 3.9 x 1.5mm)

IN STOCK: 4245pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AB1526

Bluetooth 5.0 Dual Mode Audio SoC, TWS, AAC, Dual-mic ENC, Integrated Charger, BGA

Brand: airoha

Package: BGA

IN STOCK: 25000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LP2980IM5-5.0

50mA micropower ultra-low-dropout regulator, 5V, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.1 mm)

IN STOCK: 2557pcs

Cargo cycle: 3-7 Days

The minimum order is 1