Opens in a new tab

88W8782-NAP2

Marvell Avastar 88W8782 single-chip WLAN SoC, 802.11a/b/g/n dual-band, 1×1 SISO, 150Mbps, integrated PA/LNA/CPU, SDIO/SPI/USB host interface, QFN package.

3120

Effective Inventory

Image for reference only

Manufacturer Part:

88W8782-NAP2

Package:

QFN / TFBGA

Brand:

Product Categories:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The 88W8782-NAP2 is a highly integrated wireless local area network (WLAN) system-on-chip (SoC) from Marvell’s Avastar family. Designed to support IEEE 802.11a/b/g/n standards with data rates up to 150 Mbps, this single-chip solution integrates a direct-conversion WLAN radio, baseband processor, media access controller (MAC), and an embedded Feroceon CPU (ARMv5TE-compliant) on a single die. The 1×1 SISO architecture supports both 2.4GHz and 5GHz bands with integrated power amplifiers (PA), low noise amplifiers (LNA), and T/R switches, significantly reducing external component count and solution footprint. Supporting SDIO, G-SPI, and USB host interfaces, the 88W8782-NAP2 is optimized for low-power consumer and embedded applications including printers, smart home devices, IoT gateways, and portable electronics. The chip implements advanced security standards including WPA2 (AES-CCMP) and WAPI, along with 802.11e QoS for multimedia applications.

Key Specifications

Parameter Value
Wireless Standards IEEE 802.11a/b/g/n
Operating Bands 2.4 GHz and 5 GHz (Dual-Band)
Antenna Configuration 1×1 SISO (Single-Input Single-Output)
Maximum PHY Data Rate 150 Mbps (802.11n, MCS7, 40MHz)
Modulation Schemes DSSS, OFDM (BPSK to 64-QAM)
Channel Bandwidth 20 MHz / 40 MHz
Integrated CPU Marvell Feroceon (ARMv5TE), 128 MHz max
DMA Channels 2 independent DMA channels
Host Interfaces SDIO (up to 75 MHz, 1-bit/4-bit), G-SPI, USB 2.0
Peripheral Interfaces UART, GPIO, SPI EEPROM, I2C/1-Wire/CSU
Integrated RF Frontend PA, LNA, T/R switch (2.4GHz); PA, LNA (5GHz)
Security Support WEP, WPA-TKIP, WPA2-AES-CCMP, AES-CMAC, WAPI
QoS Support IEEE 802.11e (WMM)
DFS Support 802.11h Dynamic Frequency Selection (5GHz radar detection)
Coexistence Interface 2/3/4-wire for co-located 2.4GHz radios (BT etc.)
On-Chip Memory OTP memory (eliminates external EEPROM)
Package Type QFN / TFBGA
Application Modes Infrastructure, Ad-Hoc, Mobile Hotspot

Features

  • Highly integrated single-chip WLAN SoC with minimal external BOM
  • Dual-band 2.4GHz/5GHz operation supporting 802.11a/b/g/n
  • 1×1 SISO architecture with up to 150 Mbps PHY data rate
  • Integrated direct-conversion radio eliminates external SAW filters
  • On-chip PA, LNA, and T/R switch for 2.4GHz path; PA+LNA for 5GHz
  • Embedded Feroceon CPU (ARMv5TE) at 128 MHz for protocol processing
  • Multiple host interface options: SDIO 3.0, G-SPI, USB 2.0
  • Advanced security: WPA2-Enterprise, WPA3 ready, WAPI support
  • 802.11e QoS for voice, video, and multimedia applications
  • Dynamic Frequency Selection (DFS) for 5GHz radar detection
  • Transmit beamformee support and STBC reception
  • Coexistence interface for Bluetooth and other 2.4GHz radios
  • OTP memory eliminates need for external EEPROM
  • Low power consumption for battery-operated devices
  • Marvell Mobile Hotspot (MMH) software support

Applications

  • Wireless printers and multifunction devices
  • Smart home and IoT gateway devices
  • IP cameras and security systems
  • Set-top boxes and digital media players
  • Portable electronics and mobile accessories
  • Industrial wireless communication modules
  • Medical and healthcare connectivity
  • Automotive telematics and infotainment
Product Introduction: 88W8782-NAP2 Product Introduction

The 88W8782-NAP2 is a member of Marvell’s Avastar family of highly integrated wireless LAN system-on-chip devices, designed to deliver robust WLAN connectivity with minimal external components and low power consumption. This single-chip solution integrates the complete WLAN functionality including the RF radio, baseband modem, media access controller (MAC), embedded processor, and host interface on a single die. Supporting IEEE 802.11a/b/g/n standards, the device operates in both 2.4GHz and 5GHz frequency bands with a 1×1 SISO (single-input single-output) configuration, achieving PHY data rates up to 150 Mbps using MCS7 modulation with 40MHz channel bandwidth. The integrated direct-conversion radio architecture eliminates the need for external SAW filters, while on-chip power amplifiers (PA), low noise amplifiers (LNA), and transmit/receive switches further reduce the bill of materials. The 2.4GHz path integrates a complete T/R switch, PA, and LNA, while the 5GHz path integrates PA and LNA. The device incorporates a Marvell Feroceon CPU (ARMv5TE compliant) running at up to 128 MHz, along with two independent DMA channels, to handle protocol processing and data management on-chip, reducing the load on the host processor. Host connectivity is provided through SDIO (supporting 1-bit and 4-bit modes up to 75 MHz), G-SPI, and USB 2.0 interfaces. Additional peripherals include a 16550-compatible UART, general-purpose I/O pins, a clocked serial unit supporting multiple serial protocols, and SPI EEPROM interface. On-chip OTP (one-time programmable) memory eliminates the need for external configuration EEPROM in many designs. Security features include hardware-accelerated WEP 64/128-bit encryption with TKIP processing, AES-CCMP for WPA2, AES-CMAC for 802.11w, and WAPI support. The 88W8782-NAP2 also supports 802.11e QoS for prioritized multimedia traffic, 802.11h Dynamic Frequency Selection (DFS) for 5GHz radar detection, and a coexistence interface for co-located Bluetooth or other 2.4GHz radios. Target applications include wireless printers, smart home devices, IP cameras, set-top boxes, industrial wireless modules, and portable electronics where compact form factor and low power consumption are critical.

Working Principle: 88W8782-NAP2 Working Principle

The 88W8782-NAP2 operates as a complete WLAN subsystem on a single chip, integrating all layers from the RF front-end through the MAC and host interface. In the receive path, RF signals from the antenna pass through the on-chip T/R switch and low noise amplifier (LNA) before being downconverted from RF to baseband using a direct-conversion (zero-IF) architecture. The baseband processor then performs OFDM or DSSS demodulation, channel equalization, and error correction (FEC decoding) to recover the transmitted data. The MAC layer handles frame assembly/disassembly, acknowledgment, retransmission, encryption/decryption, and quality-of-service (QoS) scheduling per 802.11e standards. In the transmit path, the MAC assembles data frames and passes them to the baseband processor for modulation and coding according to the selected data rate and modulation scheme (BPSK through 64-QAM for OFDM, CCK for DSSS). The baseband signal is upconverted to the operating RF frequency, amplified by the on-chip power amplifier (PA), and routed to the antenna through the T/R switch. The transmit power control system provides both closed-loop and open-loop power adjustment with 0.5 dB steps. The integrated Feroceon CPU executes the WLAN firmware, managing association, authentication, key management, roaming, power management, and other protocol-level functions on-chip, reducing the processing burden on the host processor. The host interface (SDIO, G-SPI, or USB) provides the data path between the WLAN chip and the host system, supporting high-speed data transfer with DMA assistance. Power management features include various sleep modes and wake-on-wireless functionality to minimize power consumption during idle periods, which is particularly important for battery-operated devices. The coexistence interface enables coordination with other radios (such as Bluetooth) sharing the 2.4GHz band, optimizing performance through time-slot arbitration and packet scheduling.

Pin Description: 88W8782-NAP2 Pin Definition and Functions
Pin Group Description
RF Pins RF antenna connection pins for 2.4GHz and 5GHz bands; connect to antenna via matching network
SDIO Interface SDIO_CLK, SDIO_CMD, SDIO_D[0:3] – SDIO 1-bit/4-bit host interface up to 75 MHz
SPI Interface SPI_CLK, SPI_MOSI, SPI_MISO, SPI_CS – General SPI host interface (G-SPI mode)
USB Interface USB_DP, USB_DM – USB 2.0 high-speed device interface
UART UART_TX, UART_RX – 16550-compatible serial port for debugging or host communication
GPIO General-purpose I/O pins configurable for various control and status functions
Power Supply Pins Multiple VDD pins for core, I/O, RF, and PLL power domains; multiple VSS ground pins
Clock Pins XTAL_IN, XTAL_OUT – external reference crystal connection (typically 40MHz)
EEPROM/OTP SPI EEPROM interface pins for external configuration memory (optional, as OTP is on-chip)
Coexistence Interface Pins for 2/3/4-wire BT/WLAN coexistence signaling
Boot Strap Pins Configuration straps sampled at power-up to set boot mode and interface selection
Application Scenarios: In which products and applications is 88W8782-NAP2 used
  • Wireless printers and multi-function printer (MFP) connectivity modules
  • Smart home hubs and IoT gateway devices
  • IP cameras (IPCs) and wireless security systems
  • Set-top boxes (STB) and over-the-top (OTT) media devices
  • Portable electronics: wireless storage, mobile hotspots
  • Industrial wireless communication and sensor gateway modules
  • Medical devices with wireless connectivity requirements
  • Automotive infotainment and telematics systems
  • Digital picture frames and smart display devices
  • Home automation and smart appliance Wi-Fi modules
Alternative Models: What chips are recommended as replacements for 88W8782-NAP2
Model Manufacturer Key Difference
88W8801 Marvell 802.11n 1×1 single-band (2.4GHz), lower cost, SDIO-only
88W8987 Marvell 802.11ac Wave-2 2×2 + BT 5.0 combo, higher performance
RTL8188CUS Realtek Single-chip 802.11n USB WLAN, 2.4GHz only, common alternative
MT7601U MediaTek 802.11n 1×1 USB Wi-Fi, 2.4GHz, cost-effective alternative
QCA9377 Qualcomm Atheros 802.11ac 1×1 + BT 4.1 combo, PCIe/SDIO interface

Recommend Parts

ISO1176TDWR

Isolated RS-485 transceiver, 40Mbps, integrated transformer driver, SOIC-16

Brand: TI

Package: SOIC-16 (DW, wide-body, 10.3 x 10.3 mm)

IN STOCK: 6874pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFB4020PBF

200V N-Channel HEXFET Power MOSFET, 31A, 68 mΩ RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 14149pcs

Cargo cycle: 3-7 Days

The minimum order is 1

NRF52832-QFAA-T

Nordic BLE SoC, ARM Cortex-M4 @ 64MHz, 64KB Flash, 32KB RAM, QFN-48

Package: See datasheet

IN STOCK: 10958pcs

Cargo cycle: 3-7 Days

The minimum order is 1

UCC28740DR

CVCC Flyback Controller, 700V startup, opto feedback, <10mW no-load, SOIC-7

Brand: TI

Package: SOIC-7 (4.9 x 3.9 x 1.75 mm)

IN STOCK: 4840pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MMUN2211LT1G

NPN digital transistor, R1=10kΩ R2=10kΩ, 50V, 100mA, SOT-23-3, pre-biased BRT switch

Brand: Onsemi

Package: SOT-23-3 (TO-236, SC-59)

IN STOCK: 8500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TMS320F2810PBKA

C2000 Delfino DSP controller, 150MHz, 128KB Flash, BGA-179

Brand: TI

Package: BGA-179 (16 x 16 mm, PBK package)

IN STOCK: 3124pcs

Cargo cycle: 3-7 Days

The minimum order is 1