Opens in a new tab

LM5119PSQX/NOPB

Dual 5 A sync buck controller, 3–100 V input, emulated current mode, 20-WQFN, automotive

10017

Effective Inventory

Image for reference only

Manufacturer Part:

LM5119PSQX/NOPB

Package:

20-WQFN (SQP) — 4.0 x 4.0 mm

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The LM5119PSQX/NOPB is a dual 5 A, current mode synchronous buck controller from Texas Instruments. Packaged in a 20-pin WQFN (SQP), it operates from an input range of 3 V to 100 V, making it ideal for high-voltage industrial and automotive power conversion. The device features emulated current mode control, adjustable switching frequency up to 1 MHz, and independent enable and soft-start for each channel.

Key Specifications

Topology Dual Synchronous Buck Controller
Input Voltage Range 3 V to 100 V
Output Current 5 A per channel (external MOSFETs)
Switching Frequency 50 kHz to 1 MHz (adjustable)
Control Mode Emulated Current Mode
Package 20-WQFN (SQP) — 4.0 x 4.0 mm
Operating Temperature -40°C to +125°C
Duty Cycle Up to 95%

Features

  • Wide 3-V to 100-V input voltage range for industrial and automotive systems
  • Emulated current mode control with cycle-by-cycle current limit
  • Dual output with 180° out-of-phase operation for reduced input capacitance
  • Independent enable, soft-start, and current limit for each channel
  • Synchronization input for multi-chip phase interleaving

Applications

  • Industrial 24 V and 48 V power distribution
  • Automotive battery-powered DC-DC conversion
  • FPGA and DSP core and I/O power supplies
  • Telecom and networking equipment power
  • Motor drive and LED lighting power supplies
Product Introduction: LM5119PSQX/NOPB Product Introduction

The LM5119 is a dual synchronous buck controller from Texas Instruments designed for high-voltage industrial and automotive power conversion applications. It operates from an input voltage range of 3 V to 100 V, driving external N-channel MOSFETs for each output channel. The emulated current mode control provides excellent transient response and cycle-by-cycle current limiting without the need for external current sense resistors. The two outputs operate 180° out of phase to minimize input ripple current and reduce input capacitor requirements. Independent enable, soft-start, and current limit functions allow flexible power sequencing.

Working Principle: LM5119PSQX/NOPB Working Principle

The LM5119 uses an emulated current mode control architecture that reconstructs the inductor current ramp internally, eliminating the need for external current sensing networks. The high-side MOSFET current is sensed through its RDS(on) or an external sense resistor, and the current information is used for both regulation and cycle-by-cycle current limiting. The error amplifier compares the output voltage feedback against a precision reference (0.8 V) and generates a control signal for the PWM comparator. The two channels operate 180° out of phase, effectively doubling the input ripple frequency and reducing the required input capacitance. An internal VCC regulator provides bias from the high-voltage input.

Pin Description: LM5119PSQX/NOPB Pin Definition and Functions
Pin Name Type Function
1 VIN Input Input supply voltage (3–100 V)
2 VCC Output Internal regulator output (bypass with cap)
3 EN1 Input Channel 1 enable
4 SS1 I/O Channel 1 soft-start (cap to GND)
5 FB1 Input Channel 1 output voltage feedback
6 COMP1 I/O Channel 1 error amplifier output
7 CS1 Input Channel 1 current sense input
8 AGND Power Analog ground
9 CS2 Input Channel 2 current sense input
10 COMP2 I/O Channel 2 error amplifier output
11 FB2 Input Channel 2 output voltage feedback
12 SS2 I/O Channel 2 soft-start (cap to GND)
13 EN2 Input Channel 2 enable
14 SYNC Input Frequency synchronization input
15 RT I/O Frequency set resistor to GND
16 HO2 Output Channel 2 high-side gate drive
17 SW2 I/O Channel 2 switch node
18 LO2 Output Channel 2 low-side gate drive
19 PGND Power Power ground
20 LO1 Output Channel 1 low-side gate drive
Application Scenarios: In which products and applications is LM5119PSQX/NOPB used
  • 24 V / 48 V industrial bus to logic power conversion
  • Automotive 12 V / 48 V battery to point-of-load supplies
  • Dual-output FPGA core and I/O voltage generation
  • Telecom base station power distribution modules
  • Broad-input-range DC-DC converters for LED driver front-ends
Alternative Models: What chips are recommended as replacements for LM5119PSQX/NOPB
Manufacturer Part Number Package Notes
TI LM5141RHBR 28-TSSOP Single 100 V sync buck controller
TI LM5143SQE/NOPB 28-WQFN Dual 100 V controller, higher integration
Analog Devices LT8653S 28-SSOP Dual 4 A, 42 V monolithic buck
Monolithic Power MP3910GS-P 28-QSOP Dual 60 V buck controller
Infineon IR3651STRPBF 28-TSSOP Dual 60 V buck controller

Recommend Parts

ISO1176TDWR

Isolated RS-485 transceiver, 40Mbps, integrated transformer driver, SOIC-16

Brand: TI

Package: SOIC-16 (DW, wide-body, 10.3 x 10.3 mm)

IN STOCK: 6874pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFB4020PBF

200V N-Channel HEXFET Power MOSFET, 31A, 68 mΩ RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 14149pcs

Cargo cycle: 3-7 Days

The minimum order is 1

NRF52832-QFAA-T

Nordic BLE SoC, ARM Cortex-M4 @ 64MHz, 64KB Flash, 32KB RAM, QFN-48

Package: See datasheet

IN STOCK: 10958pcs

Cargo cycle: 3-7 Days

The minimum order is 1

UCC28740DR

CVCC Flyback Controller, 700V startup, opto feedback, <10mW no-load, SOIC-7

Brand: TI

Package: SOIC-7 (4.9 x 3.9 x 1.75 mm)

IN STOCK: 4840pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MMUN2211LT1G

NPN digital transistor, R1=10kΩ R2=10kΩ, 50V, 100mA, SOT-23-3, pre-biased BRT switch

Brand: Onsemi

Package: SOT-23-3 (TO-236, SC-59)

IN STOCK: 8500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TMS320F2810PBKA

C2000 Delfino DSP controller, 150MHz, 128KB Flash, BGA-179

Brand: TI

Package: BGA-179 (16 x 16 mm, PBK package)

IN STOCK: 3124pcs

Cargo cycle: 3-7 Days

The minimum order is 1