Opens in a new tab

MCP4728-E

Quad 12-bit DAC with EEPROM, I2C, 2.7-5.5V, 6µs settling, ±0.2LSB DNL, MSOP-10, AEC-Q100

7250

Effective Inventory

Image for reference only

Manufacturer Part:

MCP4728-E

Package:

MSOP-10 (3.0 x 4.9 mm, 0.5mm pitch)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The MCP4728-E is a quad-channel 12-bit voltage-output Digital-to-Analog Converter (DAC) with non-volatile EEPROM memory from Microchip Technology. Featuring an I2C-compatible serial interface, this device provides four buffered voltage outputs with internal or external voltage reference selection. The on-board EEPROM allows DAC settings to persist through power cycles, with outputs available immediately after power-up. Operating from 2.7V to 5.5V, the MCP4728-E offers 6 µs settling time and ±0.2 LSB DNL accuracy.

Key Specifications

Manufacturer Microchip Technology
Resolution 12-bit
Number of Channels 4 (quad)
Output Type Voltage buffered
Interface I2C (up to 3.4 MHz HS mode)
Supply Voltage 2.7V to 5.5V
Settling Time 6 µs (typical)
DNL ±0.2 LSB (typical)
INL ±2 LSB (typical)
Internal VREF 2.048V (with gain options)
Operating Temperature -40°C to +125°C
Package MSOP-10
Non-Volatile Memory EEPROM (for DAC codes and address)
Qualification AEC-Q100 Grade 1

Features

  • 12-bit voltage output DAC with 4 buffered outputs
  • On-board non-volatile EEPROM for DAC codes & I2C address
  • Internal (2.048V) or external voltage reference per channel
  • Gain options: 1x or 2x (with internal VREF)
  • ±0.2 LSB DNL (typical)
  • Fast settling time: 6 µs
  • Rail-to-rail output operation
  • Individual normal/power-down mode per channel
  • I2C interface: Standard (100kHz), Fast (400kHz), HS (3.4MHz)
  • Low power consumption: 800 µA typical (all 4 ch active)
  • Power-down current: 40 nA typical
  • AEC-Q100 Grade 1 qualified
  • Extended temperature: -40°C to +125°C

Applications

  • Set point and offset adjustment
  • Sensor calibration and trimming
  • Closed-loop servo control
  • Low-power portable instrumentation
  • Industrial process control
  • PC peripherals and programmable voltage sources
  • Bias voltage adjustment for power amplifiers
Product Introduction: MCP4728-E Product Introduction

The MCP4728-E is a quad-channel, 12-bit voltage output Digital-to-Analog Converter (DAC) from Microchip Technology with non-volatile EEPROM memory and an I2C-compatible serial interface. Its on-board precision output amplifier achieves rail-to-rail analog output swing, providing maximum dynamic range within the supply voltage. The key differentiator of the MCP4728 is its integrated non-volatile EEPROM, which stores DAC input codes, device configuration bits, and I2C address bits. This enables the DAC outputs to be available immediately after power-up with the saved settings, eliminating the need for the host controller to reconfigure the DAC on each power cycle. Each of the four channels can independently select between internal or external voltage reference. The internal 2.048V precision reference provides accurate and stable output voltages, with gain options of 1x (0 to 2.048V) or 2x (0 to 4.096V). Alternatively, each channel can use VDD as the reference for a 0 to VDD output range. The device supports individual power-down mode per channel, with typical power-down current of only 40 nA when all channels are powered down. The I2C interface supports Standard (100 kHz), Fast (400 kHz), and High-Speed (3.4 MHz) modes, offering flexibility for various system architectures. AEC-Q100 Grade 1 qualification ensures suitability for automotive applications. The ‘E’ suffix indicates the extended temperature range of -40°C to +125°C.

Working Principle: MCP4728-E Working Principle

The MCP4728-E converts 12-bit digital values into proportional analog voltage outputs. The conversion architecture is based on a resistor-string (R-string) DAC topology, which provides inherent monotonicity and low glitch energy. Each channel has its own DAC register and output buffer amplifier. The I2C interface receives digital data from the host controller and loads it into the DAC registers. For normal operation, the digital value in the DAC register is converted to an analog voltage by the resistor string, then buffered by a precision output amplifier capable of driving moderate loads. The output amplifier features rail-to-rail operation, allowing the output to swing very close to both supply rails. Voltage reference selection is per-channel: internal reference mode uses the on-chip 2.048V bandgap reference, providing high accuracy and stability; external reference mode uses VDD as the reference, providing a full-supply output range. The gain setting (1x or 2x) is available only with the internal reference and is controlled by configuration bits in the DAC register. The EEPROM memory stores both the DAC code values and the I2C device address bits, and is programmed through I2C commands. An on-board charge pump generates the high voltages needed for EEPROM programming. The RDY/BSY pin provides status indication during EEPROM write operations. The LDAC pin synchronizes updates across multiple DAC channels or can be used to read/write the I2C address bits. A Power-on Reset (POR) circuit ensures reliable device initialization at power-up, loading the saved configuration from EEPROM into the DAC registers.

Pin Description: MCP4728-E Pin Definition and Functions
Pin Name Type Function
1 VDD Power Positive supply voltage (2.7V to 5.5V)
2 SCL Input I2C serial clock input
3 SDA I/O I2C serial data I/O
4 LDAC Input DAC latch synchronization input / address read
5 RDY/BSY Output EEPROM ready/busy status output (open-drain)
6 VOUT A Output DAC channel A analog voltage output
7 VOUT B Output DAC channel B analog voltage output
8 VOUT C Output DAC channel C analog voltage output
9 VOUT D Output DAC channel D analog voltage output
10 VSS Ground Ground reference
Application Scenarios: In which products and applications is MCP4728-E used
  • Set point adjustment and offset trimming in industrial systems
  • Sensor calibration and precision analog frontends
  • Closed-loop servo control and motor speed control
  • Low-power portable instrumentation and medical devices
  • Programmable voltage and current sources
  • Bias voltage adjustment for power amplifiers and RF circuits
Alternative Models: What chips are recommended as replacements for MCP4728-E
Manufacturer Part Number Package Notes
Microchip MCP4725-E/CH SOT-23-6 Single 12-bit DAC with EEPROM
Microchip MCP4726-E/CH SOT-23-6 Single 12-bit DAC with VREF pin
Texas Instruments DAC5578 TSSOP-16 Octal 12-bit I2C DAC
Analog Devices AD5627R SOT-23-8 Dual 12-bit SPI DAC with reference
MaxLinear X9241 SOIC-20 Quad digital potentiometer alternative

Recommend Parts

ISO1176TDWR

Isolated RS-485 transceiver, 40Mbps, integrated transformer driver, SOIC-16

Brand: TI

Package: SOIC-16 (DW, wide-body, 10.3 x 10.3 mm)

IN STOCK: 6874pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFB4020PBF

200V N-Channel HEXFET Power MOSFET, 31A, 68 mΩ RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 14149pcs

Cargo cycle: 3-7 Days

The minimum order is 1

NRF52832-QFAA-T

Nordic BLE SoC, ARM Cortex-M4 @ 64MHz, 64KB Flash, 32KB RAM, QFN-48

Package: See datasheet

IN STOCK: 10958pcs

Cargo cycle: 3-7 Days

The minimum order is 1

UCC28740DR

CVCC Flyback Controller, 700V startup, opto feedback, <10mW no-load, SOIC-7

Brand: TI

Package: SOIC-7 (4.9 x 3.9 x 1.75 mm)

IN STOCK: 4840pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MMUN2211LT1G

NPN digital transistor, R1=10kΩ R2=10kΩ, 50V, 100mA, SOT-23-3, pre-biased BRT switch

Brand: Onsemi

Package: SOT-23-3 (TO-236, SC-59)

IN STOCK: 8500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

PIC32MX795F512L-80I/PF

32-bit PIC32MX MCU with Ethernet/CAN/USB, 80MHz, 512KB Flash, TQFP-100, industrial

Brand: MICROCHIP

Package: TQFP-100 (14 x 14 mm)

IN STOCK: 7912pcs

Cargo cycle: 3-7 Days

The minimum order is 1