Opens in a new tab

TJA1042

High-speed CAN transceiver with standby, ISO 11898-5, 1Mbps, 5V/3.3V I/O, SOIC8, NXP automotive

12600

Effective Inventory

Image for reference only

Manufacturer Part:

TJA1042

Package:

SOIC-8 (3.9 mm width)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The TJA1042 is a high-speed CAN transceiver with Standby mode from NXP Semiconductors, fully compliant with ISO 11898-2 and ISO 11898-5 standards. Optimized for automotive and industrial CAN networks requiring low-power standby with bus wake-up capability, it supports data rates up to 1 Mbit/s and operates from a 4.5 V to 5.5 V supply. A dedicated VIO pin enables direct interface with both 3.3 V and 5 V microcontrollers without external level shifting. The TJA1042 delivers outstanding electromagnetic compatibility performance, achieving excellent EMC at 500 kbit/s even without a common-mode choke. Key features include TXD dominant timeout for fault protection, bus-failure diagnosis capability, under-voltage detection on both supplies, thermal shutdown, and very low standby current with selective wake-up. AEC-Q100 qualified and packaged in a standard SOIC-8 form factor, it is widely used in automotive body modules, gateway ECUs, and low-power CAN nodes where power efficiency and reliable wake-up are essential.

Key Specifications

Standard Compliance ISO 11898-2 and ISO 11898-5
Data Rate Up to 1 Mbit/s
Supply Voltage (VCC) 4.5 V to 5.5 V
I/O Supply (VIO) 3.3 V to 5.5 V
Bus Voltage Range -27 V to +40 V
Differential Output (dominant) 1.5 V to 3.0 V
Supply Current (Normal, rec.) ~17 mA typical
Supply Current (Standby) ~10 µA typical
Bus ESD Protection ±8 kV (HBM)
Operating Modes Normal, Standby
Wake-up Detection Yes (bus wake-up pattern)
TXD Dominant Timeout Yes (prevents stuck dominant)
Bus Failure Diagnosis Yes (open/short detection)
Thermal Shutdown Yes
Under-Voltage Detection Yes (VCC and VIO)
I/O Level Compatibility 3.3 V and 5 V (via VIO)
Temperature Range -40°C to +125°C
Qualification AEC-Q100 Grade 1
Package SOIC-8 (3.9 mm width)

Features

  • Fully ISO 11898-2 and ISO 11898-5 compliant
  • Up to 1 Mbit/s data rate
  • Very low standby current with bus wake-up
  • Separate VIO pin for 3.3 V / 5 V I/O adaptation
  • Excellent EMC performance (no common-mode choke needed @ 500kbit/s)
  • TXD dominant time-out function
  • Bus failure diagnosis capability
  • Thermal shutdown protection
  • Under-voltage detection on VCC and VIO Predictable behavior in all power states
  • Bus passive when unpowered (ideal zero load)
  • AEC-Q100 qualified (automotive grade 1)
  • Wide temperature range: -40°C to +125°C
  • SOIC-8 surface mount package
  • RoHS compliant, halogen-free / green product

Applications

  • Automotive body control modules (BCM)
  • Automotive gateway control units
  • Automotive lighting and comfort systems
  • Industrial control and automation networks
  • Low-power CAN sensor nodes with wake-up
  • Mixed 3.3 V / 5 V CAN systems
  • Building automation and HVAC control
  • Battery-powered CAN devices
  • Automotive infotainment and telematics
  • Electric vehicle auxiliary systems
  • Marine and off-highway vehicle networks
Product Introduction: TJA1042 Product Introduction

The TJA1042 is a high-speed CAN (Controller Area Network) transceiver from NXP Semiconductors, optimized for mixed-voltage CAN networks in automotive and industrial applications. It provides the interface between a CAN protocol controller and the physical two-wire CAN bus, fully compliant with ISO 11898-2 and ISO 11898-5 standards. Supporting data rates up to 1 Mbit/s, the TJA1042 features a very-low-current Standby mode with bus wake-up functionality and a dedicated VIO pin for direct interface with 3.3 V or 5 V microcontrollers without external level shifters. The device offers exceptional electromagnetic compatibility (EMC) performance even without a common-mode choke at 500 kbit/s. Advanced features include TXD dominant timeout, bus-failure diagnosis, under-voltage detection on both VCC and VIO supplies, and thermal shutdown. Packaged in an SOIC-8 and AEC-Q100 qualified, the TJA1042 is the go-to choice for vehicle body electronics, gateway modules, and low-power CAN nodes requiring wake-up capability.

Working Principle: TJA1042 Working Principle

The TJA1042 functions as the CAN physical layer, translating logic-level signals between the CAN controller and the differential CAN bus. In Normal mode, a low-level TXD input drives the transceiver to pull CANH high and CANL low (dominant state, creating a ~2 V differential voltage), while a high TXD lets both bus lines rest at ~2.5 V (recessive state, near-zero differential voltage). The receiver compares CANH and CANL and outputs the decoded data on RXD. The Standby mode, activated via the STB pin, places the transceiver in a low-power state (~10 µA) where only a low-power receiver monitors the bus; when a wake-up pattern is detected, the RXD pin is pulled low to signal the microcontroller. The VIO pin sets the I/O interface voltage level, enabling direct connection to both 3.3 V and 5 V microcontrollers. The EMC-optimized output stage with controlled slew rates reduces electromagnetic emissions, while the differential receiver with wide common-mode input range provides high noise immunity. The TXD dominant time-out function prevents a stuck-low TXD fault from permanently holding the bus dominant, enhancing system reliability. Bus-failure detection provides diagnostic capabilities for identifying open-circuit, short-to-ground, or short-to-battery conditions.

Pin Description: TJA1042 Pin Definition and Functions
Pin No. Symbol Type Description
1 TXD I Transmit data input (from CAN controller, low = dominant)
2 GND P Ground
3 VCC P Transceiver supply voltage (4.5 V to 5.5 V)
4 RXD O Receive data output (to CAN controller, low = dominant)
5 VIO P I/O supply voltage (3.3 V to 5.5 V for I/O level shifting)
6 CANL I/O CAN bus low-level line
7 CANH I/O CAN bus high-level line
8 STB I Standby mode control (high = standby, low = normal)

Operating Modes:

  • Normal mode (STB = LOW): Full transceiver operation (transmit + receive)
  • Standby mode (STB = HIGH): Low power, only wake-up receiver active, RXD indicates bus wake-up
Application Scenarios: In which products and applications is TJA1042 used
  • Automotive body control modules (BCM)
  • Automotive gateway ECUs
  • Automotive lighting and comfort electronics
  • Industrial control and factory automation
  • Low-power CAN nodes with wake-up
  • Mixed 3.3V/5V CAN systems
  • Building automation and HVAC
  • Battery-powered CAN devices
  • Automotive infotainment systems
Alternative Models: What chips are recommended as replacements for TJA1042
Model Manufacturer Key Diff Description
TJA1040 NXP Similar Older version, similar feature set
TJA1044 NXP CAN FD 5 Mbps, CAN FD capable
TJA1048 NXP Dual Dual-channel CAN transceiver
TJA1145 NXP Partial networking CAN FD with partial networking
NCV7342 onsemi Standby onsemi equivalent with standby mode
SN65HVD234 TI Standby TI 3.3V CAN with standby

Recommend Parts

ISO1176TDWR

Isolated RS-485 transceiver, 40Mbps, integrated transformer driver, SOIC-16

Brand: TI

Package: SOIC-16 (DW, wide-body, 10.3 x 10.3 mm)

IN STOCK: 6874pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFB4020PBF

200V N-Channel HEXFET Power MOSFET, 31A, 68 mΩ RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 14149pcs

Cargo cycle: 3-7 Days

The minimum order is 1

NRF52832-QFAA-T

Nordic BLE SoC, ARM Cortex-M4 @ 64MHz, 64KB Flash, 32KB RAM, QFN-48

Package: See datasheet

IN STOCK: 10958pcs

Cargo cycle: 3-7 Days

The minimum order is 1

UCC28740DR

CVCC Flyback Controller, 700V startup, opto feedback, <10mW no-load, SOIC-7

Brand: TI

Package: SOIC-7 (4.9 x 3.9 x 1.75 mm)

IN STOCK: 4840pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MMUN2211LT1G

NPN digital transistor, R1=10kΩ R2=10kΩ, 50V, 100mA, SOT-23-3, pre-biased BRT switch

Brand: Onsemi

Package: SOT-23-3 (TO-236, SC-59)

IN STOCK: 8500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TMS320F2810PBKA

C2000 Delfino DSP controller, 150MHz, 128KB Flash, BGA-179

Brand: TI

Package: BGA-179 (16 x 16 mm, PBK package)

IN STOCK: 3124pcs

Cargo cycle: 3-7 Days

The minimum order is 1