Opens in a new tab

ADS1115IRUGR

16-bit delta-sigma ADC, 4-channel MUX, PGA 2/3-16x, 8-860SPS, I2C interface, internal 2.048V ref, temp sensor, 150uA, 10-QFN 2×1.5mm, TI ADS1115.

35000

Effective Inventory

Image for reference only

Manufacturer Part:

ADS1115IRUGR

Package:

10-Lead QFN (2mm x 1.5mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The ADS1115IRUGR is a precision 16-bit analog-to-digital converter (ADC) from Texas Instruments (Burr-Brown product line) featuring an onboard reference and oscillator. The device performs conversions at rates up to 860 samples per second (SPS) and offers four multiplexed inputs that can be configured as two differential or four single-ended channels. A programmable gain amplifier (PGA) provides gains from 2/3 to 16, allowing measurement of both large and small signals with high resolution. The ADS1115 communicates over an I2C-compatible interface and supports two address pins for connecting up to eight devices on the same bus. With an ultra-low supply current of only 150 microamps at 8 SPS, the device is ideal for battery-powered and portable applications. Additional features include an integrated temperature sensor, alert/ready pin with programmable comparator and hysteresis, and a sleep mode that reduces current to 0.5 microamps. The ADS1115IRUGR is packaged in a 10-pin QFN (2mm x 1.5mm) and operates over the industrial temperature range of -40C to +125C.

Key Specifications

Parameter Conditions Min Typ Max Unit
Resolution No missing codes — 16 — Bits
Number of Input Channels 4 single-ended or 2 differential 4 channels (multiplexed) —
Architecture Delta-sigma (ΔΣ) 1st-order modulator + digital filter —
Programmable Data Rate — 8 128 860 SPS
PGA Gain Settings — 2/3, 1, 2, 4, 8, 16 V/V
Full-Scale Input Range PGA=2/3 ±6.144 V V
Full-Scale Input Range PGA=16 ±0.256 V V
INL (Integral Nonlinearity) End-point fit — ±0.5 ±2 LSB
Offset Error After calibration — 5 — µV
Offset Drift — — 3 — µV/C
Gain Error At 25C — 0.01 0.15 %
Gain Drift — — 1 — ppm/C
Supply Voltage Range Single supply 2.0 — 5.5 V
Supply Current (Operating) Continuous conversion — 150 200 µA
Supply Current (Power-Down) Sleep mode — 0.5 — µA
Internal Reference — — 2.048 — V
Oscillator Internal — — — On-chip
Interface I2C-compatible Standard, fast, high-speed modes up to 3.4 MHz —
Address Pins Up to 8 devices per bus ADDR pin selects one of 8 addresses —
Temperature Sensor Integrated — 0.5 — C resolution
ALERT/RDY Pin Programmable comparator with hysteresis Interrupt or comparator mode —
Package 10-Lead QFN (2mm x 1.5mm x 0.4mm) —
Operating Temperature Industrial grade -40 — +125 degrees C

Features

  • Wide supply range: 2.0 V to 5.5 V single supply
  • 16-bit resolution, no missing codes
  • Programmable data rate: 8 SPS to 860 SPS
  • Programmable gain amplifier: 2/3 to 16
  • Four input channels: 4 single-ended or 2 differential
  • Internal 2.048 V reference and oscillator
  • I2C-compatible interface: up to 3.4 MHz high-speed mode
  • Programmable comparator with ALERT/RDY output
  • Integrated temperature sensor (0.5C resolution)
  • Ultra-low power: 150 µA continuous conversion mode
  • Low power-down current: 0.5 µA sleep mode
  • Single-cycle settling conversion
  • Up to 8 devices per I2C bus via address pin
  • Small 10-pin QFN package (2mm x 1.5mm)
  • Industrial temperature range: -40C to +125C
  • Compatible with both 3.3V and 5V microcontrollers

Applications

  • Portable instrumentation and battery-powered measurement
  • Consumer electronics battery voltage and current monitoring
  • Industrial sensor signal conditioning
  • Temperature measurement with thermocouples and RTDs
  • Wearable devices and health monitors
  • Smart home sensor nodes
  • Power supply voltage and current monitoring
  • Arduino/Raspberry Pi data acquisition projects
  • \li>Automotive sensor interfaces

  • Low-power data acquisition systems
Product Introduction: ADS1115IRUGR Product Introduction

The ADS1115IRUGR is a precision 16-bit delta-sigma analog-to-digital converter from Texas Instruments Burr-Brown product line, designed for low-power and space-constrained applications. With its four-channel input multiplexer, programmable gain amplifier, internal reference, and on-chip oscillator, the ADS1115 provides a complete analog-to-digital conversion solution in an ultra-small 10-pin QFN package measuring only 2mm x 1.5mm. The input multiplexer supports four single-ended inputs or two differential inputs, providing flexibility for various measurement configurations. The programmable gain amplifier offers settings from 2/3 to 16, enabling measurement of signals ranging from millivolts up to the full supply voltage. At the highest gain setting of 16, the full-scale range is only ±0.256V, making it possible to measure very small signals with high resolution. The device operates from a single 2.0V to 5.5V supply, making it compatible with both 3.3V and 5V systems. Communication is accomplished through an I2C-compatible interface supporting standard, fast, and high-speed modes up to 3.4 MHz. An address pin allows up to eight ADS1115 devices to share the same I2C bus. The ALERT/RDY pin provides a programmable comparator function with hysteresis that can trigger an interrupt when measured values exceed user-defined thresholds, or it can indicate when conversion data is ready. An integrated temperature sensor with 0.5C resolution eliminates the need for a separate temperature monitoring IC in many applications. With a supply current of only 150 microamps in continuous conversion mode and 0.5 microamps in sleep mode, the ADS1115 is exceptionally well-suited for battery-powered and energy-harvesting applications. The ADS1115IRUGR is the ultra-small QFN package version, and the R suffix indicates tape and reel packaging.

Working Principle: ADS1115IRUGR Working Principle

The ADS1115 uses a delta-sigma (ΔΣ) architecture to achieve high resolution at relatively low sampling rates. At the heart of the converter is a first-order delta-sigma modulator that converts the analog input voltage into a stream of 1s and 0s at a high frequency. The modulator works by repeatedly sampling the input voltage and comparing it with a reference voltage, producing a bitstream whose average value represents the input. The noise from the conversion process is shaped toward higher frequencies (noise shaping), where it can be easily removed by digital filtering. Following the modulator is a digital decimation filter that takes the high-frequency bitstream and converts it into a 16-bit digital output word at the programmed data rate. This filter also provides anti-aliasing, greatly simplifying the requirements for any analog anti-aliasing filter that may precede the ADC. The programmable gain amplifier (PGA) is placed before the modulator, amplifying the input signal to better match the full-scale range of the ADC, thereby increasing the effective resolution for small signals. The input multiplexer allows the ADC to sequentially measure different input channels, with the PGA and modulator being shared resources. The internal reference voltage of 2.048V is generated by a bandgap reference circuit, and the internal oscillator provides the clock for both the modulator and digital filter, eliminating the need for external timing components. The I2C interface allows a microcontroller to configure the device and read conversion results. The programmable comparator monitors the conversion result against user-programmed upper and lower threshold registers, and the ALERT/RDY pin asserts when the result is out of range, with programmable hysteresis and latching behavior. The device also supports a single-shot conversion mode where it performs one conversion, stores the result, and then enters a low-power sleep state – this is how the ultra-low average power consumption is achieved in many applications.

Pin Description: ADS1115IRUGR Pin Definition and Functions
Pin No. Name Description
1 ADDR I2C address select pin. Connect to GND, VDD, SDA, or SCL to select one of four I2C addresses (additional variants available for 8 total addresses).
2 ALERT/RDY Alert / data ready output. Open-drain, requires pull-up resistor. Programmable as comparator output for limit detection or as conversion ready indicator.
3 AIN0 Analog input 0. Can be used as single-ended input or paired with AIN1 for differential measurement.
4 AIN1 Analog input 1. Can be used as single-ended input or paired with AIN0 for differential measurement.
5 AIN2 Analog input 2. Can be used as single-ended input or paired with AIN3 for differential measurement.
6 AIN3 Analog input 3. Can be used as single-ended input or paired with AIN2 for differential measurement.
7 GND Ground reference pin.
8 VDD Power supply pin (2.0V to 5.5V). Bypass with 0.1 uF ceramic capacitor to GND.
9 SCL I2C serial clock input. Requires pull-up resistor.
10 SDA I2C serial data input/output (open-drain). Requires pull-up resistor.
Pad EP Exposed pad. Must connect to GND for thermal and electrical performance.
Application Scenarios: In which products and applications is ADS1115IRUGR used
  • Battery voltage and current monitoring in portable electronics
  • Temperature measurement with thermistors, thermocouples, and RTDs
  • Wearable health monitoring devices and fitness trackers
  • Smart home and IoT sensor nodes
  • Industrial sensor signal conditioning and data acquisition
  • Arduino, Raspberry Pi, and embedded system ADC expansion
  • Portable test and measurement equipment
  • Power supply monitoring and fault detection
  • Automotive sensor interfaces (with appropriate protection)
  • Low-power energy harvesting sensor systems
Alternative Models: What chips are recommended as replacements for ADS1115IRUGR
Model Manufacturer Key Difference
ADS1015IRUGR Texas Instruments 12-bit version, higher speed (3.3kSPS), lower resolution, same pinout/package
ADS1115IDGSR Texas Instruments Same ADC in 10-pin VSSOP package, larger but easier to hand-solder
ADS1113 Texas Instruments 1-channel version, no multiplexer, no comparator, lower cost
MCP3424 Microchip 18-bit 4-channel ADC with PGA, I2C, alternative from Microchip
LTC2493 ADI / Linear Tech 24-bit 2-channel delta-sigma ADC, I2C, higher resolution option

Recommend Parts

ISO1176TDWR

Isolated RS-485 transceiver, 40Mbps, integrated transformer driver, SOIC-16

Brand: TI

Package: SOIC-16 (DW, wide-body, 10.3 x 10.3 mm)

IN STOCK: 6874pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFB4020PBF

200V N-Channel HEXFET Power MOSFET, 31A, 68 mΩ RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 14149pcs

Cargo cycle: 3-7 Days

The minimum order is 1

NRF52832-QFAA-T

Nordic BLE SoC, ARM Cortex-M4 @ 64MHz, 64KB Flash, 32KB RAM, QFN-48

Package: See datasheet

IN STOCK: 10958pcs

Cargo cycle: 3-7 Days

The minimum order is 1

UCC28740DR

CVCC Flyback Controller, 700V startup, opto feedback, <10mW no-load, SOIC-7

Brand: TI

Package: SOIC-7 (4.9 x 3.9 x 1.75 mm)

IN STOCK: 4840pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MMUN2211LT1G

NPN digital transistor, R1=10kΩ R2=10kΩ, 50V, 100mA, SOT-23-3, pre-biased BRT switch

Brand: Onsemi

Package: SOT-23-3 (TO-236, SC-59)

IN STOCK: 8500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TMS320F2810PBKA

C2000 Delfino DSP controller, 150MHz, 128KB Flash, BGA-179

Brand: TI

Package: BGA-179 (16 x 16 mm, PBK package)

IN STOCK: 3124pcs

Cargo cycle: 3-7 Days

The minimum order is 1