Opens in a new tab

Home » Sensors, Temperature Sensors » ADT7470ARQZ-REEL7

ADT7470ARQZ-REEL7

Temperature sensor hub + 4-channel PWM fan controller, monitors up to 10 TMP05/TMP06 sensors via daisy-chain, I2C/SMBus 400kHz, SMBALERT, FULL_SPEED, 16-QSOP, ADI ADT7470.

5600

Effective Inventory

Image for reference only

Manufacturer Part:

ADT7470ARQZ-REEL7

Package:

16-Lead QSOP

Product Categories:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The ADT7470ARQZ-REEL7 is a temperature sensor hub and PWM fan controller from Analog Devices, designed for thermal management in computers, servers, networking equipment, and telecommunications systems. The device monitors up to 10 remote temperature sensors (TMP05 or TMP06) daisy-chained together on a single 1-wire bus, and independently monitors and controls up to four cooling fans using PWM outputs and tachometer inputs. All measured values (temperatures and fan speeds) are compared against user-programmable limit values, with out-of-limit conditions flagged via status registers and the SMBALERT interrupt output. The ADT7470 communicates with the host system through a fast-mode (up to 400 kHz) I2C/SMBus interface. A three-state ADDR pin allows up to three ADT7470 devices to share the same bus. Additional features include FULL_SPEED input for hardware-based full-speed fan override, auto and manual fan control modes, and support for SMBus 2.0 specifications. The ADT7470ARQZ-REEL7 is packaged in a 16-lead QSOP and operates over the -40C to +125C temperature range.

Key Specifications

r>

Parameter Conditions Min Typ Max Unit
Remote Temperature Channels Via TMP05/TMP06 daisy-chain — — 10 sensors
Temperature Resolution From TMP05/TMP06 PWM data — 0.0625 — C
Temperature Range From TMP05/TMP06 sensors -55 — +150 degrees C
Fan Control Channels Independent — — 4 fans
Fan PWM Frequency Programmable 11 Hz to 99 Hz (base frequency 22.5 kHz option) Hz
Fan Tachometer Inputs 4 channels Supports 2-pulse, 4-pulse, and 8-pulse fans —
Fan Speed Range 10% to 100% PWM — — — Wide range
Interface I2C/SMBus Fast mode up to 400 kHz, SMBus 2.0 compliant —
Address Selection 3-state ADDR pin Up to 3 devices per bus —
Interrupt Output SMBALERT Open-drain, reports out-of-limit conditions —
FULL_SPEED Input Hardware override Active low, forces all fans to full speed —
Supply Voltage (VCC) — 3.0 3.3 5.5 V
Supply Current Operating — 3.5 6.0 mA
Supply Current Standby — 120 — µA
PWM Output Type Open-drain Requires external pull-up resistor —
Alarm/Status Registers Sticky bits Limit comparison with latching status bits —
Fan Fault Detection Under-speed detection Programmable minimum speed threshold per fan —
Fan Control Modes — Manual mode and automatic (look-up table) mode —
Package 16-Lead QSOP (ARQ, 150mil body width) —
Operating Temperature — -40 — +125 degrees C
Storage Temperature — -65 — +150 degrees C

Features

  • Monitors up to 10 remote temperature sensors (TMP05/TMP06) via daisy-chain
  • Independently monitors and controls up to 4 fans
  • PWM outputs drive each fan at user-programmable duty cycle
  • FULL_SPEED hardware input overrides software to run fans at 100%
  • SMBALERT interrupt output for system controller notification
  • 3-state ADDR pin for up to 3 devices on single I2C bus
  • I2C/SMBus interface up to 400 kHz
  • SMBus 2.0 compliant (backward compatible with SMBus 1.1)
  • Limit comparison on all monitored values
  • Sticky status bits retain fault information until read
  • Automatic fan control mode (temperature-based look-up table)
  • Manual fan control mode (direct PWM duty cycle)
  • Fan speed measurement via tachometer inputs
  • Fan under-speed detection and alarm
  • Programmable PWM frequency from 11 Hz to 99 Hz
  • Wide supply voltage range: 3.0V to 5.5V
  • Low power standby mode: 120 µA typical
  • Industrial temperature range: -40C to +125C
  • 16-lead QSOP package (0.15 inch body width)
  • RoHS compliant matte tin finish (Z suffix)

Applications

  • Server and workstation thermal management
  • Networking equipment (routers, switches, hubs)
  • Telecommunications infrastructure
  • Desktop and workstation computers
  • Industrial PCs and embedded computing
  • Power supply thermal monitoring and cooling control
  • Data center equipment cooling
  • Storage systems and RAID controllers
  • Medical equipment with active cooling
  • Any system requiring multi-point temperature monitoring and fan control
Product Introduction: ADT7470ARQZ-REEL7 Product Introduction

The ADT7470ARQZ-REEL7 is a versatile thermal management controller from Analog Devices that combines multi-channel temperature monitoring with PWM fan control in a single 16-lead QSOP package. Unlike fan controllers with integrated temperature sensors, the ADT7470 is designed to interface with external TMP05 or TMP06 temperature sensors connected in a daisy-chain configuration on a single wire, allowing up to 10 temperature monitoring points distributed throughout a system. This architecture provides significant flexibility in locating temperature sensors at critical hot spots (CPU, GPU, power supplies, hard drives, etc.) without requiring individual ADC channels for each sensor. The TMP05/TMP06 sensors convert temperature into a PWM signal whose duty cycle is proportional to temperature, and the ADT7470 decodes these PWM signals to get temperature readings with 0.0625C resolution. On the fan control side, the ADT7470 provides four independent PWM outputs for driving fan motors and four corresponding tachometer inputs for monitoring fan speed. Each fan can be controlled either manually (direct duty cycle set by register writes) or automatically using a look-up table that maps temperature thresholds to fan speed settings, providing closed-loop thermal control without CPU intervention. All measured values – both temperatures and fan speeds – are continuously compared against user-programmed limit values stored in internal registers. Out-of-limit conditions (over-temperature, fan under-speed, etc.) are flagged in status registers and can generate an SMBALERT interrupt to notify the system controller. The status bits are sticky, meaning they remain set once a fault is detected and must be explicitly cleared by the system controller after reading, ensuring that transient faults are not missed between polling intervals. The device communicates with the host through an I2C/SMBus interface operating at up to 400 kHz, and a three-state address pin allows up to three ADT7470 devices to be used on the same bus for systems requiring more fans or temperature sensors.

Working Principle: ADT7470ARQZ-REEL7 Working Principle

The ADT7470 operates as both a temperature sensor hub and a fan controller, with both functions managed by an internal state machine and register set accessible via the I2C/SMBus interface. For temperature monitoring, the device reads PWM-formatted temperature data from daisy-chained TMP05 or TMP06 temperature sensors. When a measurement cycle is initiated (either by writing to the start bit in the configuration register or automatically in continuous measurement mode), the ADT7470 sends a start pulse down the TMP_IN line, which triggers the first TMP05/TMP06 sensor in the chain to begin transmitting its temperature reading as a PWM pulse. Each sensor in the daisy chain transmits its reading sequentially, with the temperature value encoded in the pulse width (the ratio of high time to total period of the PWM signal). The ADT7470 measures this ratio for each sensor in the chain and converts it to a temperature value using the known transfer function of the TMP05/TMP06, storing the results in the temperature registers (0x20 through 0x29 for up to 10 sensors). The highest temperature measured across all sensors is also stored in a dedicated register (0x78) for simplified thermal management algorithms. For fan control, the ADT7470 generates PWM signals on four output pins (PWM1 through PWM4) that drive the fan motors (typically through external MOSFETs or fan drivers, as the outputs are open-drain). The duty cycle of each PWM output determines the fan speed. In manual mode, the duty cycle is set directly by writing to the PWM duty cycle registers. In automatic mode, the duty cycle is determined by a look-up table programmed into the device: the device compares the measured temperature against programmed temperature thresholds and adjusts the fan speed accordingly, providing automatic closed-loop thermal control. To monitor actual fan speed, each tachometer input (TACH1 through TACH4) counts pulses from the fan tachometer output over a defined measurement window, and the resulting count is stored in the TACH measurement registers. These values are compared against minimum speed thresholds to detect stalled or under-speed fans. All out-of-limit conditions (both temperature and fan speed) set corresponding bits in the interrupt status registers and can assert the SMBALERT output if that interrupt source is enabled.

Pin Description: ADT7470ARQZ-REEL7 Pin Definition and Functions
Pin No. Name Type Description
1 SCL Digital input (OD) SMBus serial clock input. Requires external pull-up resistor. Supports fast mode (400 kHz).
2 GND Ground Ground reference pin.
3 VCC Power supply Power supply (3.0V to 5.5V). Can be powered from 3.3V standby supply.
4 TACH3 Digital input (OD) Fan 3 tachometer input. Reads fan speed pulses from fan 3.
5 PWM2 Digital I/O (OD) PWM output for fan 2 speed control. Can also be configured as GPIO.
6 TACH1 Digital input (OD) Fan 1 tachometer input. Reads fan speed pulses from fan 1.
7 TACH2 Digital input (OD) Fan 2 tachometer input. Reads fan speed pulses from fan 2.
8 PWM3 Digital I/O (OD) PWM output for fan 3 speed control. Can also be configured as GPIO.
9 TACH4 Digital input (OD) Fan 4 tachometer input. Reads fan speed pulses from fan 4.
10 PWM4 Digital I/O (OD) PWM output for fan 4 speed control. Can also be configured as GPIO.
11 ADDR 3-state input Address select. 3-level input (high, low, float) sets SMBus device address (3 possible addresses).
12 TMP_IN Digital input (OD) Temperature sensor PWM input. Reads PWM output from daisy-chained TMP05/TMP06 temperature sensors.
13 FULL_SPEED / TMP_START Digital I/O Full-speed fan override input (active low) / TMP05 start output. Pulled low forces all fans to 100% PWM duty cycle.
14 SMBALERT Digital output (OD) SMBus alert interrupt output (open-drain). Asserts when monitored values exceed limits. Requires pull-up resistor.
15 PWM1 Digital I/O (OD) PWM output for fan 1 speed control. Can also be configured as GPIO.
16 SDA Digital I/O (OD) SMBus serial data (bidirectional, open-drain). Requires external pull-up resistor.
Application Scenarios: In which products and applications is ADT7470ARQZ-REEL7 used
  • Server rack and blade server thermal management systems
  • Network routers, switches, and telecom equipment cooling control
  • Desktop PC and workstation fan control and temperature monitoring
  • Industrial PC and embedded computing thermal management
  • Data center equipment cooling infrastructure
  • Power supply units with thermal monitoring and fan speed control
  • RAID controllers and storage systems thermal management
  • Medical diagnostic equipment requiring active cooling
  • Test and measurement instrumentation thermal control
  • Multi-point temperature monitoring with distributed sensors
Alternative Models: What chips are recommended as replacements for ADT7470ARQZ-REEL7
Model Manufacturer Key Difference
ADT7470ARQ Analog Devices Tube packaging version (non-reel)
ADT7473ARQZ-REEL Analog Devices Remote thermal diode + local temp sensor, 3-fan controller, different sensor interface
ADT7466ARQZ Analog Devices 4-channel thermal diode monitor + 2-fan controller, different architecture
ADT7467ARQZ Analog Devices dBCool remote thermal controller, 3 temp channels + 4 fans
MAX6650 ADI / Maxim Tachometer fan-speed regulator with SMBus, alternative Maxim product

Recommend Parts

ISO1176TDWR

Isolated RS-485 transceiver, 40Mbps, integrated transformer driver, SOIC-16

Brand: TI

Package: SOIC-16 (DW, wide-body, 10.3 x 10.3 mm)

IN STOCK: 6874pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFB4020PBF

200V N-Channel HEXFET Power MOSFET, 31A, 68 mΩ RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 14149pcs

Cargo cycle: 3-7 Days

The minimum order is 1

NRF52832-QFAA-T

Nordic BLE SoC, ARM Cortex-M4 @ 64MHz, 64KB Flash, 32KB RAM, QFN-48

Package: See datasheet

IN STOCK: 10958pcs

Cargo cycle: 3-7 Days

The minimum order is 1

UCC28740DR

CVCC Flyback Controller, 700V startup, opto feedback, <10mW no-load, SOIC-7

Brand: TI

Package: SOIC-7 (4.9 x 3.9 x 1.75 mm)

IN STOCK: 4840pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MMUN2211LT1G

NPN digital transistor, R1=10kΩ R2=10kΩ, 50V, 100mA, SOT-23-3, pre-biased BRT switch

Brand: Onsemi

Package: SOT-23-3 (TO-236, SC-59)

IN STOCK: 8500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TMS320F2810PBKA

C2000 Delfino DSP controller, 150MHz, 128KB Flash, BGA-179

Brand: TI

Package: BGA-179 (16 x 16 mm, PBK package)

IN STOCK: 3124pcs

Cargo cycle: 3-7 Days

The minimum order is 1