Opens in a new tab

AT91SAM7S256D-AU

ARM7TDMI 32-bit MCU, 256KB Flash, 64KB SRAM, 55MHz/55MIPS, 10-bit ADC x 8ch, USB FS, USART, SPI, SSC, TWI, PWM x 4ch, PDC, AIC, LQFP-64, Atmel AT91SAM7S256D-AU.

2800

Effective Inventory

Image for reference only

Manufacturer Part:

AT91SAM7S256D-AU

Package:

LQFP-64 (10x10mm)

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The AT91SAM7S256D-AU is a 32-bit microcontroller from Atmel (now Microchip) based on the ARM7TDMI processor core, featuring 256KB of high-speed internal Flash memory and 64KB of SRAM. Part of the AT91SAM7S series, this device delivers high performance with a maximum operating frequency of 55MHz, achieving up to 55 MIPS of throughput. The integrated high-speed Flash supports single-cycle access at up to 30MHz, with a prefetch buffer optimizing Thumb instruction execution at maximum frequency. The SAM7S256 includes a rich set of peripherals including a USB 2.0 Full-Speed device port, one USART, an SPI, an SSC (Synchronous Serial Controller), a TWI (I2C-compatible), an 8-channel 10-bit ADC, a 3-channel 16-bit Timer Counter, a 4-channel PWM controller, and a Peripheral DMA Controller (PDC) for efficient data transfer without CPU intervention. The Advanced Interrupt Controller (AIC) provides individually maskable, eight-level priority vectored interrupts. The device also includes a Power Management Controller (PMC) with software-controlled power optimization, a Reset Controller with brown-out detection, and a real-time timer. Operating from a 1.65V to 1.95V core supply with 3.3V I/O, the AT91SAM7S256D-AU is packaged in a 64-lead LQFP and is suitable for a wide range of embedded applications including industrial control, consumer products, and USB-connected devices.

Key Specifications

Parameter Conditions Min Typ Max Unit
Core Processor ARM7TDMI (ARM Thumb)
Core Architecture 32-bit RISC (16-bit Thumb instruction set)
Maximum Clock Frequency 55 MHz
Maximum Throughput 55 MIPS
Program Flash Memory Single plane, 256-byte pages 256 KB
Flash Pages 1024 pages of 256 bytes 1024 pages
Flash Access Time Single cycle access 30 MHz
Flash Programming Page program + auto-erase 6 ms
Full Chip Erase 15 ms
Flash Endurance Write/erase cycles 10000 cycles
Data Retention 10 years
Flash Security Security bit + 16 sector lock bits
Internal SRAM Single-cycle access 64 KB
Prefetch Buffer Thumb instruction optimization Yes
Core Supply Voltage (VDDCORE) 1.65 1.8 1.95 V
I/O Supply Voltage (VDDIO) 3.3 V
General Purpose I/O PIOA 32 I/O lines
USART 1 (USART0)
Debug UART (DBGU) 1 (2-wire)
SPI Master/Slave 1 (with 4 chip selects)
SSC (Synchronous Serial) 1 (I2S/AC97 compatible)
TWI (Two-Wire) I2C compatible 1
USB 2.0 Device Full Speed (12Mbps) Yes
Timer/Counter Channels 16-bit 3 channels (TC0)
PWM Channels 4 channels (PWM0-PWM3)
ADC Resolution 10-bit
ADC Channels 8 channels
Peripheral DMA Controller Yes (PDC)
Advanced Interrupt Controller 8-level priority Yes (AIC)
Reset Controller POR + BOD Yes (RSTC)
Power Management Yes (PMC with PLL)
Real-time Timer (RTT) 32-bit + alarm Yes
Periodic Interval Timer 20-bit + 12-bit Yes (PIT)
Watchdog Timer Windowed, 12-bit Yes (WDT)
JTAG Debug Interface EmbeddedICE Yes
Operating Temperature Industrial -40 +85 °C
Package LQFP-64 (10x10mm), 0.5mm pitch

Features

  • ARM7TDMI 32-bit RISC processor with Thumb instruction set
  • High performance: up to 55 MIPS at 55 MHz
  • 256KB high-speed internal Flash memory (single cycle up to 30MHz)
  • 64KB high-speed internal SRAM (single-cycle access)
  • Prefetch buffer for optimized Thumb execution
  • 10,000 Flash write cycles, 10-year data retention
  • Flash security: security bit + 16 sector lock bits
  • Embedded In-Circuit Emulator (EmbeddedICE)
  • 32 programmable I/O lines with input change interrupt
  • 1 USART + 1 Debug UART (DBGU)
  • SPI with 4 chip selects, Master/Slave
  • SSC (Synchronous Serial Controller) – I2S/AC97 compatible
  • TWI (Two-Wire Interface, I2C compatible)
  • USB 2.0 Full-Speed Device port
  • 3-channel 16-bit Timer/Counter
  • 4-channel PWM controller
  • 8-channel 10-bit ADC
  • Peripheral DMA Controller (PDC) for all serial peripherals
  • Advanced Interrupt Controller (AIC) with 8-level priority
  • Power Management Controller (PMC) with PLL
  • Reset Controller with POR and brown-out detector
  • Real-time Timer (RTT) and Periodic Interval Timer (PIT)
  • Windowed Watchdog Timer
  • Power supply: 1.65V-1.95V core, 3.3V I/O
  • Low power modes: Idle, Slow Clock, Standby
  • SAM-BA bootloader for in-system programming
  • LQFP-64 (10x10mm) package
  • Industrial temperature range (-40 to +85°C)

Applications

  • Industrial control and automation
  • USB-connected peripherals
  • Data acquisition and logging systems
  • Motor control and drive systems
  • Test and measurement equipment
  • Consumer electronics
  • Medical devices
  • Point-of-sale terminals
  • Networking and communication equipment
  • Security systems
  • Robotics
  • Automotive aftermarket
Product Introduction: AT91SAM7S256D-AU Product Introduction

The AT91SAM7S256D-AU is a 32-bit ARM7TDMI-based microcontroller from Atmel (now Microchip Technology), offering high performance and rich peripheral integration in a compact LQFP-64 package. At the core is an ARM7TDMI processor capable of up to 55 MIPS throughput at 55MHz, supporting both 32-bit ARM and 16-bit Thumb instruction sets for optimal code density. The device features 256KB of high-speed embedded Flash memory organized as 1024 pages of 256 bytes, with single-cycle access at up to 30MHz and a prefetch buffer that optimizes Thumb instruction execution at maximum frequency. The 64KB of high-speed SRAM provides single-cycle access for fast data processing. A key feature is the Peripheral DMA Controller (PDC) that enables data transfers between peripherals and memory without CPU intervention, significantly reducing processor overhead. The AT91SAM7S256D-AU includes an extensive set of communication peripherals: one USART, one Debug UART, SPI with 4 chip selects, SSC for synchronous serial (I2S/AC97 compatible), TWI (I2C compatible), and USB 2.0 Full-Speed Device. Control peripherals include a 3-channel 16-bit Timer/Counter, 4-channel PWM controller, 8-channel 10-bit ADC, and a Periodic Interval Timer. The Advanced Interrupt Controller (AIC) provides individually maskable, eight-level priority vectored interrupts for efficient real-time response. The Power Management Controller (PMC) with integrated PLL allows flexible clock generation and power optimization. The device operates from 1.65V to 1.95V core voltage with 3.3V I/O, supporting multiple low-power modes including Idle, Slow Clock (down to 500Hz), and Standby. With the integrated SAM-BA bootloader, in-system programming is possible via USB or UART without external programming hardware. The AT91SAM7S256D-AU, with its ‘D’ revision and ‘AU’ suffix indicating LQFP-64 industrial temperature package, is well-suited for industrial control, data acquisition, USB peripherals, motor control, and a wide range of embedded applications.

Working Principle: AT91SAM7S256D-AU Working Principle

The AT91SAM7S256D-AU is built around the ARM7TDMI 32-bit RISC processor core, which uses a von Neumann architecture with a single 32-bit bus for both instructions and data. The core supports both 32-bit ARM and 16-bit Thumb instruction sets — Thumb mode typically reduces code size by 30-40% while maintaining most of ARM’s performance. At reset, the CPU starts executing from address 0x00000000 in the Flash memory, which contains the reset vector pointing to the initialization code. The Memory Controller (MC) manages access to the internal Flash and SRAM, with the Embedded Flash Controller handling Flash programming operations. The Prefetch Buffer reads 32-bit words from Flash and buffers them for efficient Thumb instruction execution, effectively doubling throughput at higher frequencies by reducing Flash access bottlenecks. The Power Management Controller (PMC) generates the system clock from multiple sources: a low-power RC oscillator, a 3-20MHz main oscillator, and a Phase-Locked Loop (PLL) that multiplies the main clock up to the maximum 55MHz operating frequency. The PMC also controls peripheral clock gating, allowing individual peripherals to be powered down when not in use for energy savings. The Advanced Interrupt Controller (AIC) manages all interrupt sources, providing eight priority levels and vectored interrupt handling that eliminates software polling overhead. The Peripheral DMA Controller (PDC) is a key architectural feature: each serial peripheral has dedicated transmit and receive DMA channels that automatically transfer data between the peripheral and memory without CPU intervention, triggered automatically when the peripheral is ready. This enables high-speed data transfers while keeping the CPU free for other tasks or in low-power modes. The USB 2.0 Full-Speed Device port supports 12Mbps operation and includes integrated transceivers. The ADC is a 10-bit successive approximation type with 8 external channels and up to 300kS/s sampling rate. The Timer Counter block provides three 16-bit counters supporting capture, compare, PWM, and waveform generation modes. The device includes comprehensive system management features: Power-On Reset (POR), Brown-Out Detector (BOD), Watchdog Timer (WDT), Real-Time Timer (RTT), and Periodic Interval Timer (PIT).

Pin Description: AT91SAM7S256D-AU Pin Definition and Functions

The AT91SAM7S256D is available in a 64-lead LQFP package (10x10mm). Major pin groups include:

Pin Group Description
Power Pins VDDIO (3.3V I/O), VDDCORE (1.8V core), VDDFLASH (Flash), GND
PA0-PA31 32 PIO lines, multiplexed with peripheral I/O
USART0 RXD0, TXD0, SCK0, RTS0, CTS0 (multiplexed on PA)
SPI MISO, MOSI, SPCK, NPCS0-NPCS3 (multiplexed on PA)
TWI TWD (data), TWCK (clock) – I2C compatible
SSC TF, TK, TD, RF, RK (I2S/AC97 serial audio)
USB DM, DP (USB D- and D+)
Timer/Counter TCLK0, TIOA0, TIOB0, TIOA1, TIOB1, TIOA2, TIOB2
PWM PWM0, PWM1, PWM2, PWM3 (4 channels)
ADC AD0-AD7 (8 analog input channels), ADVREF (reference)
JTAG Debug TCK, TMS, TDI, TDO, JTAGSEL
Reset NRST (active low reset)
Oscillator XIN, XOUT (main crystal, 3-20MHz)
Wake-up WAKEUP0 (wake-up from low-power mode)
Erase ERASE (Flash erase pin)
Test TST (test mode pin)
Fast Flash Programming PGM interface pins for production programming

Note: Many pins have multiple functions via PIO multiplexing (Peripheral A or B). Refer to the official datasheet for complete pin assignment.

Application Scenarios: In which products and applications is AT91SAM7S256D-AU used
  • Industrial control and factory automation
  • USB data acquisition and interface devices
  • Motor control and servo drives
  • Test and measurement instruments
  • Data loggers and recorders
  • Medical devices and diagnostic equipment
  • Point-of-sale (POS) terminals
  • Networking equipment and gateways
  • Security and access control systems
  • Robotics and motion control
  • Consumer electronics products
  • Automotive aftermarket accessories
Alternative Models: What chips are recommended as replacements for AT91SAM7S256D-AU
Model Manufacturer Key Difference
AT91SAM7S512-AU Atmel 512KB Flash (double), dual plane Flash
AT91SAM7S128-AU Atmel 128KB Flash, 32KB SRAM (smaller version)
AT91SAM7S64-AU Atmel 64KB Flash, 16KB SRAM (entry level)
AT91SAM7X256 Atmel With Ethernet MAC and CAN, LQFP-100
STM32F103RBT6 STMicroelectronics Cortex-M3 alternative, 128KB Flash, LQFP-64

Recommend Parts

ISO1176TDWR

Isolated RS-485 transceiver, 40Mbps, integrated transformer driver, SOIC-16

Brand: TI

Package: SOIC-16 (DW, wide-body, 10.3 x 10.3 mm)

IN STOCK: 6874pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFB4020PBF

200V N-Channel HEXFET Power MOSFET, 31A, 68 mΩ RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 14149pcs

Cargo cycle: 3-7 Days

The minimum order is 1

NRF52832-QFAA-T

Nordic BLE SoC, ARM Cortex-M4 @ 64MHz, 64KB Flash, 32KB RAM, QFN-48

Package: See datasheet

IN STOCK: 10958pcs

Cargo cycle: 3-7 Days

The minimum order is 1

UCC28740DR

CVCC Flyback Controller, 700V startup, opto feedback, <10mW no-load, SOIC-7

Brand: TI

Package: SOIC-7 (4.9 x 3.9 x 1.75 mm)

IN STOCK: 4840pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MMUN2211LT1G

NPN digital transistor, R1=10kΩ R2=10kΩ, 50V, 100mA, SOT-23-3, pre-biased BRT switch

Brand: Onsemi

Package: SOT-23-3 (TO-236, SC-59)

IN STOCK: 8500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TMS320F2810PBKA

C2000 Delfino DSP controller, 150MHz, 128KB Flash, BGA-179

Brand: TI

Package: BGA-179 (16 x 16 mm, PBK package)

IN STOCK: 3124pcs

Cargo cycle: 3-7 Days

The minimum order is 1