Opens in a new tab

OPA2192IDGKR

Dual Precision Op Amp, 5uV Vos, 0.2uV/C Drift, 10MHz, RRO, VSSOP-8

6789

Effective Inventory

Image for reference only

Manufacturer Part:

OPA2192IDGKR

Package:

VSSOP-8 / MSOP-8 (3.0 x 3.0 x 0.9 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The OPA2192IDGKR from Texas Instruments is a dual 36V precision e-trim op amp with 5 uV offset, 0.2 uV/C drift, rail-to-rail output, and 10 MHz bandwidth in a VSSOP-8 package.

Key Specifications

Type Dual Precision e-Trim Operational Amplifier
Channels 2
Supply Voltage +/-2.25 V to +/-18 V (4.5 V to 36 V)
Offset Voltage +/-5 uV (max)
Offset Drift 0.2 uV/C (max)
Input Bias Current +/-5 pA (typical)
Gain Bandwidth Product 10 MHz
Slew Rate 20 V/us
CMRR 140 dB (typical)
Open-Loop Gain 134 dB (typical)
Input Noise (0.1-10Hz) 120 nVpp
Supply Current per Channel 1.3 mA (typical)
Package VSSOP-8 (DGK)
Operating Temperature -40C to +125C

Features

  • Ultra-low 5 uV max offset voltage with e-trim technology
  • 0.2 uV/C max offset drift over temperature
  • Rail-to-rail output swing
  • 140 dB CMRR for precision differential sensing
  • 10 MHz bandwidth with 20 V/us slew rate
  • EMI-filtered inputs
  • Multiplexed input friendly (no phase reversal)

Applications

  • Precision instrumentation amplifiers
  • Medical ECG/EEG front-ends
  • Weigh scale and strain gauge amplifiers
  • High-impedance sensor signal conditioning
Product Introduction: OPA2192IDGKR Product Introduction

The OPA2192IDGKR from Texas Instruments is a dual precision operational amplifier using proprietary e-trim technology to achieve +/-5 uV max offset voltage and 0.2 uV/C max drift without laser trimming. The rail-to-rail output stage maximizes dynamic range in single-supply applications. The 140 dB CMRR and 134 dB open-loop gain enable precise differential measurements in bridge and instrumentation circuits. The 10 MHz bandwidth and 20 V/us slew rate support precision active filters and signal conditioning beyond DC. EMI-filtered inputs reduce susceptibility to RF interference in noisy environments. The device operates from +/-2.25 V to +/-18 V dual supplies or 4.5 V to 36 V single supply.

Working Principle: OPA2192IDGKR Working Principle

The OPA2192IDGKR uses TI’s e-trim technology, which performs electronic trimming of the input offset voltage during the final wafer test. Unlike laser trimming which physically cuts metal links, e-trim uses programmable non-volatile memory cells that adjust the input stage current mirror to null the offset. This method produces no mechanical stress and is more stable over time and temperature. The input stage uses a folded-cascode architecture with complementary N-channel and P-channel input pairs to achieve rail-to-rail common-mode input range. The output stage uses a class AB push-pull configuration that swings to within 50 mV of each rail at light loads. The 140 dB CMRR is achieved through precise matching of the input pair tail currents and active load balancing. The EMI filter on the inputs consists of a low-pass RC network that attenuates RF signals above approximately 10 MHz before they can be rectified by the input transistors.

Pin Description: OPA2192IDGKR Pin Definition and Functions
Pin Name Type Function
1 1OUT Output Channel 1 output
2 1IN- Input Channel 1 inverting input
3 1IN+ Input Channel 1 non-inverting input
4 VS- Power Negative supply
5 2IN+ Input Channel 2 non-inverting input
6 2IN- Input Channel 2 inverting input
7 2OUT Output Channel 2 output
8 VS+ Power Positive supply
Application Scenarios: In which products and applications is OPA2192IDGKR used
  • Dual-channel strain gauge amplifier with 5uV offset for weigh scale
  • Medical ECG instrumentation amplifier with 140dB CMRR
  • High-precision 4-20mA receiver with sub-uV drift
  • Precision active Sallen-Key filter for 16-bit ADC driver
Alternative Models: What chips are recommended as replacements for OPA2192IDGKR
Manufacturer Part Number Package Notes
TI OPA192IDGKR VSSOP-8 Single version
TI OPA4192IDR SOIC-14 Quad version
ADI ADA4522-2ARZ SOIC-8 Dual, zero-drift, 55V
TI OPA2189IDGKR VSSOP-8 Dual, zero-drift, lower noise
ADI ADA4099-2ARZ SOIC-8 Dual, 36V, low power

Recommend Parts

MCP6S26-I

6-channel PGA, SPI interface, gains 1-32V/V, 10MHz BW, rail-to-rail, 2.5-5.5V, SOIC-14

Brand: MICROCHIP

Package: SOIC-14 (150 mils body width)

IN STOCK: 6800pcs

Cargo cycle: 3-7 Days

The minimum order is 1

W25Q80VSSI

8Mbit Serial Flash, Quad SPI, 104MHz, SOIC-8, 2.7-3.6V

Brand: Winbond

Package: SOIC-8 208mil (5.3×8.0mm)

IN STOCK: 4316pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MM3Z9V1

9.1V 200mW Zener diode, SOD-323, onsemi/Diotec

Brand: ON

Package: SOD-323 (2.5 x 1.25 x 0.85 mm)

IN STOCK: 10735pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AT89S51

8-bit 8051 MCU, 4KB ISP Flash, 128B RAM, 32 I/O, 2 timers, UART, watchdog timer, dual DPTR, 33MHz, ISP programming, PDIP-40, Atmel AT89S51.

Package: PDIP-40 / TQFP-44 / PLCC-44

IN STOCK: 15000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

GD32F303CBT6

Cortex-M4 32-bit MCU, 120MHz, 128KB Flash, 32KB SRAM, LQFP-48

Brand: gigadevice

Package: LQFP-48 (7x7mm, 0.5mm pitch)

IN STOCK: 3342pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MIC5205-3.3YM5-TR

3.3V 150mA ultra-low-noise LDO, 165mV dropout, 30uVrms noise, SOT-23-5

Brand: MICROCHIP

Package: SOT-23-5 (2.9 x 1.6 x 1.1mm)

IN STOCK: 9858pcs

Cargo cycle: 3-7 Days

The minimum order is 1