Opens in a new tab

SP3232EEY-L

RS-232 2Tx/2Rx, 3.0-5.5V, 120kbps, charge pump 4×0.1µF, ±15kV ESD HBM, TSSOP-16, -40~85°C

15000

Effective Inventory

Image for reference only

Manufacturer Part:

SP3232EEY-L

Package:

TSSOP-16 (5.0 x 6.4 x 1.1 mm, 0.65mm pitch)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

The SP3232EEY-L from MaxLinear (formerly Sipex) is a 2-driver/2-receiver RS-232 transceiver operating from a single +3.0-V to +5.5-V supply. It features an integrated high-efficiency charge pump requiring only four 0.1-µF external capacitors, true EIA/TIA-232-F compliance, 120-kbps minimum data rate, and enhanced ESD protection (±15-kV HBM, ±8-kV IEC 61000-4-2 contact discharge). The -L suffix denotes the TSSOP-16 package rated for -40°C to +85°C. Supply current is 0.3 mA typical at no load. Applications include notebook computers, industrial controllers, and embedded RS-232 interfaces.

Product Introduction: SP3232EEY-L Product Introduction

The SP3232EEY-L is a true RS-232 transceiver from MaxLinear’s SP3232E series, providing 2 drivers and 2 receivers in a single TSSOP-16 package. It is designed for portable and handheld applications requiring RS-232 communication from 3.3-V or 5-V logic supplies.

The integrated charge pump doubles and inverts the supply voltage to generate the ±5.4-V (typical) RS-232 output levels required by EIA/TIA-232-F, using only four 0.1-µF external capacitors. This is a significant improvement over older designs requiring 1-µF capacitors, reducing board area and cost.

The device meets all EIA/TIA-232-F specifications with a minimum data rate of 120 kbps under full 3-kΩ/1000-pF load, sufficient for standard serial communication up to 115.2 kbps with margin. The driver output swing exceeds ±5.0 V with a 3-kΩ load, ensuring compatibility with all standard RS-232 receivers.

ESD protection is a standout feature: ±15-kV Human Body Model, ±15-kV IEC 61000-4-2 air discharge, and ±8-kV IEC 61000-4-2 contact discharge on all RS-232 pins. This eliminates the need for external TVS diodes in most applications, simplifying the BOM.

The EEY-L suffix denotes: E = enhanced ESD version, Y = TSSOP-16 package, -L = -40°C to +85°C industrial temperature range, tape and reel. The SP3232E does not include shutdown or tri-state features (those are on the SP3222E variant). Supply current is 0.3 mA typical at no load with 3.3-V supply, making it suitable for always-on serial ports in battery-powered devices.

Working Principle: SP3232EEY-L Working Principle

**Charge Pump (Voltage Doublers):** The SP3232E uses a regulated dual charge pump to generate RS-232 voltage levels from a single 3.0-5.5-V supply. The first stage is a voltage doubler (C1 charge pump) that produces V+ ≈ 2 × VCC from the C1+/C1- pins. The second stage is a voltage inverter (C2 charge pump) that produces V- ≈ -2 × VCC from the C2+/C2- pins. A V+ storage capacitor (C3) and V- storage capacitor (C4) smooth the outputs. Regulation limits V+ and V- magnitudes to approximately 5.5 V to prevent exceeding RS-232 maximums.

**Driver Stage:** Each driver converts TTL/CMOS logic levels (0.8-V low, 2.4-V high thresholds) to RS-232 levels (±5.4-V swing typical). When the logic input is high, the output swings negative; when low, the output swings positive (inverting). The output is current-limited and can drive a 3-kΩ load with 1000-pF cable capacitance.

**Receiver Stage:** Each receiver converts RS-232 input levels (±3-V to ±15-V range) to TTL/CMOS logic levels. The input threshold is 0.8-V TTL compatible with 0.5-V typical hysteresis for noise immunity. A 5-kΩ pull-down resistor to ground on each receiver input ensures a defined logic-high output when the RS-232 cable is disconnected.

Pin Description: SP3232EEY-L Pin Definition and Functions
Pin Name Type Description
1 C1+ I/O Charge pump capacitor C1 positive terminal; connect 0.1µF ceramic to C1- (pin 3)
2 V+ P Doubled positive voltage output (~5.4V); connect 0.1µF storage capacitor to GND
3 C1- I/O Charge pump capacitor C1 negative terminal
4 C2+ I/O Charge pump capacitor C2 positive terminal; connect 0.1µF ceramic to C2- (pin 5)
5 C2- I/O Charge pump capacitor C2 negative terminal
6 V- P Inverted negative voltage output (~-5.4V); connect 0.1µF storage capacitor to GND
7 T2OUT O Driver 2 RS-232 output; swings ±5.4V typical; connects to RS-232 cable
8 R2IN I Receiver 2 RS-232 input; accepts ±15V range; 5kΩ internal pull-down to GND
9 R2OUT O Receiver 2 TTL/CMOS output; VCC-referenced logic level; drives UART RX
10 T2IN I Driver 2 TTL/CMOS input; connects to UART TX; inverting to RS-232 output
11 T1IN I Driver 1 TTL/CMOS input; connects to UART TX
12 R1OUT O Receiver 1 TTL/CMOS output; drives UART RX
13 R1IN I Receiver 1 RS-232 input; accepts ±25V absolute max; 5kΩ pull-down
14 T1OUT O Driver 1 RS-232 output; swings ±5.4V typical
15 GND G Ground; connect to PCB ground plane; charge pump returns through this pin
16 VCC P Supply voltage 3.0-5.5V; bypass with 0.1µF ceramic close to pin
Application Scenarios: In which products and applications is SP3232EEY-L used
Application Description
Embedded MCU RS-232 Port Interface 3.3V MCU UART to RS-232 serial port; charge pump generates ±5.4V from 3.3V supply; only 4 external 0.1µF caps needed; ±15kV ESD protection eliminates external TVS; 120kbps supports standard 115.2kbaud with margin
Industrial Controller Communication Provide RS-232 debug/programming port on 3.3V or 5V industrial controller; -40~85°C range covers industrial environments; ESD protection handles cable hot-plug transients; TSSOP-16 fits space-constrained boards
Portable Instrument Serial Link Enable RS-232 data download from 3.3V battery-powered instrument; 0.3mA no-load Iq minimizes battery drain; 0.1µF charge pump caps minimize board area; always-on receiver detects incoming connection without enable control
Alternative Models: What chips are recommended as replacements for SP3232EEY-L
Model Manufacturer Compatibility Key Difference
MAX3232CUE ADI (Maxim) Pin-Compatible Same TSSOP-16 pinout; same 3.0-5.5V supply; 250kbps (faster); 0.1µF caps; ±15kV ESD; industry-standard alternative; widely available
SP3232EBCA-L MaxLinear Pin-Compatible, Same Series Same function in SSOP-16 package (wider body); different package land pattern; same electrical specs; use when SSOP preferred over TSSOP
ST3232EBTR ST Pin-Compatible TSSOP-16; 3.0-5.5V; 400kbps (faster); 0.1µF caps; ±15kV ESD; ST second source; use for supply chain diversification
SP3222ECA-L MaxLinear Functional Upgrade Same family with shutdown mode (1µA Iq); 20-pin SSOP/TSSOP; EN and SHDN pins; use when shutdown capability needed for ultra-low-power standby

Recommend Parts

ISL95855HRTZ-T

IMVP8 3+2+1 phase buck controller, R3 technology, 4.5-25V input, 48-TQFN

Brand: Renesas

Package: 48-TQFN (6×6 mm, exposed pad)

IN STOCK: 2156pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFB4019PBF

150V N-Channel HEXFET Power MOSFET, 47A, 34 mΩ RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 2409pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MSP430F247TPMR

TI MSP430 MCU, 16-bit RISC, 92KB Flash, 8KB RAM, 16MHz, LQFP-64

Package: See datasheet

IN STOCK: 13371pcs

Cargo cycle: 3-7 Days

The minimum order is 1

UCC28740DR

CVCC Flyback Controller, 700V startup, opto feedback, <10mW no-load, SOIC-7

Brand: TI

Package: SOIC-7 (4.9 x 3.9 x 1.75 mm)

IN STOCK: 4840pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MMUN2211LT1G

NPN digital transistor, R1=10kΩ R2=10kΩ, 50V, 100mA, SOT-23-3, pre-biased BRT switch

Brand: Onsemi

Package: SOT-23-3 (TO-236, SC-59)

IN STOCK: 8500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

PIC32MX795F512L-80I/PF

32-bit PIC32MX MCU with Ethernet/CAN/USB, 80MHz, 512KB Flash, TQFP-100, industrial

Brand: MICROCHIP

Package: TQFP-100 (14 x 14 mm)

IN STOCK: 7912pcs

Cargo cycle: 3-7 Days

The minimum order is 1