Opens in a new tab

TLC59116IRHBR

16-Ch I2C LED Driver, 100mA, 8-bit PWM+Dot Correction, QFN-24

4567

Effective Inventory

Image for reference only

Manufacturer Part:

TLC59116IRHBR

Package:

QFN-24 (4.0 x 4.0 x 0.9 mm, 0.5mm pitch)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The TLC59116IRHBR from Texas Instruments is a 16-channel I2C constant-current LED driver with 8-bit PWM dimming, 8-bit dot correction, and open/short detection in a QFN-24 package.

Key Specifications

Type 16-Channel I2C Constant-Current LED Driver
Channels 16 (current sink)
Max Current per Channel 100 mA (programmable via external resistor)
PWM Resolution 8-bit (256 steps)
Dot Correction 8-bit per channel
Interface I2C (up to 1 MHz Fast-mode Plus)
I2C Addresses 14 selectable (A0-A3 pins)
Output Voltage Up to 17V (LED supply)
Supply Voltage (Logic) 3.0 V to 5.5 V
Diagnostics Open-load, short-to-GND detection
Package QFN-24 (4 x 4 mm)
Operating Temperature -40C to +125C

Features

  • 16 independent constant-current LED outputs
  • 8-bit PWM dimming per channel (256 steps)
  • 8-bit dot correction for brightness matching
  • I2C Fast-mode Plus up to 1 MHz
  • 14 selectable I2C addresses for bus multiplexing
  • Open-load and short-to-GND detection
  • Thermal shutdown protection
  • Output enable for global dimming control

Applications

  • RGB LED matrix and display backlighting
  • Keypad illumination
  • General-purpose LED lighting control
  • Signage and decorative lighting
Product Introduction: TLC59116IRHBR Product Introduction

The TLC59116IRHBR from Texas Instruments is a 16-channel constant-current LED driver controlled via I2C interface. Each output provides up to 100 mA with current set by an external resistor. The 8-bit PWM controller provides 256 brightness steps per channel for smooth dimming, while the 8-bit dot correction compensates for LED brightness variations across channels. The I2C interface supports Fast-mode Plus at up to 1 MHz, and 14 selectable I2C addresses (via A0-A3 pins) allow multiple devices on a single bus. On-chip diagnostics detect open-load and short-to-GND conditions. The QFN-24 package provides a compact footprint for space-constrained applications. The thermal shutdown protects against excessive junction temperature.

Working Principle: TLC59116IRHBR Working Principle

The TLC59116IRHBR uses 16 DMOS transistors as current-sink outputs, each with an independent 8-bit PWM controller and 8-bit dot correction register. An external resistor (REXT) connected to the REXT pin sets the global maximum output current: IOUT(max) = 850 / REXT (for REXT in Ohms, IOUT in mA). The dot correction register scales the current from 0% to 100% of IOUT(max) in 256 steps, compensating for LED brightness bin variations. The PWM register independently controls the duty cycle of each output from 0/256 to 255/256, providing brightness control. The effective output current is IOUT(eff) = IOUT(max) x DotCorrection/255 x PWM/255. The I2C interface writes to control registers, PWM registers, and dot correction registers. Open-load detection works by briefly turning on the output and sensing if the voltage rises above a threshold, indicating no LED connected. Short-to-GND detection monitors if the output voltage stays near ground when the LED should be on.

Pin Description: TLC59116IRHBR Pin Definition and Functions
Pin Name Type Function
Multiple OUT0-OUT15 Output 16 LED current-sink outputs
Dedicated SDA/SCL I/O I2C data and clock
Dedicated A0-A3 Input I2C address selection
Dedicated REXT Input External current-set resistor
Dedicated OE Input Output enable (active LOW)
Dedicated VCC/GND Power 3.0-5.5V logic supply
Application Scenarios: In which products and applications is TLC59116IRHBR used
  • 16-segment RGB LED display driver with I2C control from MCU
  • White LED backlight array with dot correction for uniform brightness
  • Keypad backlighting with individual LED brightness control
  • Multi-device I2C bus LED driver (14 addresses for 224 LEDs)
Alternative Models: What chips are recommended as replacements for TLC59116IRHBR
Manufacturer Part Number Package Notes
TI TLC59116IPWR TSSOP-24 Same device, TSSOP package
NXP PCA9635PW TSSOP-28 16-ch, I2C, no dot correction
TI TLC5940NT DIP-28 16-ch, SPI, 12-bit PWM, grayscale
TI TLC59208ARGER QFN-20 8-ch, I2C, lower cost
ISSI IS31FL3733-QFLS4-TR QFN-44 12×16 matrix, I2C, animation

Recommend Parts

MSP432P401RIPZR

Ultra-low-power Cortex-M4F MCU, 48MHz, 256KB Flash, 14-bit ADC, 850nA standby, 100-LQFP

Brand: TI

Package: 100-LQFP (14 x 14 x 1.4mm)

IN STOCK: 3750pcs

Cargo cycle: 3-7 Days

The minimum order is 1

PTN78060WAH

4.5A positive-input buck-IT module, adjustable, SMD module

Brand: TI

Package: Module (34.3 x 19.3 x 8.2 mm)

IN STOCK: 4786pcs

Cargo cycle: 3-7 Days

The minimum order is 1

PIC16F1526-I/PT

8-bit PIC16 MCU, 14KB Flash, 768B RAM, 30-ch 10-bit ADC, 10x CCP, 64-TQFP, XLP

Brand: MICROCHIP

Package: TQFP-64 (10.0 x 10.0 x 1.05 mm)

IN STOCK: 5600pcs

Cargo cycle: 3-7 Days

The minimum order is 1

R2A20178NP

8-channel 8-bit voltage output DAC, R-2R architecture, buffered rail-to-rail output, SPI interface up to 25MHz, 2.7-5.5V

Brand: Renesas

Package: 24-pin HWQFN (4x4x0.75mm)

IN STOCK: 6399pcs

Cargo cycle: 3-7 Days

The minimum order is 1

VS-40CPQ100-N3

Dual Schottky rectifier, common cathode, 2x20A, 100V, 0.61V VF, TO-247AC-3L, Vishay Q-series, 175 degC TJ, guard ring

Brand: VISHAY

Package: TO-247AC 3L (3-lead through-hole, 15.5mm width, tab for heatsink, common cathode configuration)

IN STOCK: 8950pcs

Cargo cycle: 3-7 Days

The minimum order is 1

BSC040N10NS5

OptiMOS 5 N-ch 100V 4mΩ 136A MOSFET, SuperSO8

Brand: infineon

Package: PG-TDSON-8 (SuperSO8, 5 x 6mm)

IN STOCK: 10509pcs

Cargo cycle: 3-7 Days

The minimum order is 1