Opens in a new tab

ENC28J60-I/SS

10Mbps Ethernet Controller, SPI, MAC+PHY, 8KB Buffer, SSOP-28

6789

Effective Inventory

Image for reference only

Manufacturer Part:

ENC28J60-I/SS

Package:

SSOP-28 (7.8 x 5.3 x 1.8 mm, 0.65mm pitch)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The ENC28J60-I/SS from Microchip Technology is a standalone 10 Mbps Ethernet controller with SPI interface, integrated MAC and PHY, and 8 KB TX/RX buffer in a SSOP-28 package.

Key Specifications

Type Standalone 10Base-T Ethernet Controller with SPI
Speed 10 Mbps (10Base-T)
Interface SPI (up to 20 MHz)
Buffer 8 KB dual-port SRAM (TX+RX)
Integrated MAC + 10Base-T PHY
Supply Voltage 3.1 V to 3.6 V (core) + 3.0-3.6V (I/O)
LED Outputs 2 (Link, Activity)
Package SSOP-28 (5.3 x 7.8mm)
Operating Temperature -40C to +85C (I grade)

Features

  • Standalone Ethernet controller – no MCU Ethernet peripheral needed
  • SPI host interface (up to 20 MHz clock)
  • Integrated MAC and 10Base-T PHY
  • 8 KB dual-port SRAM buffer for TX and RX
  • Automatic polarity correction
  • Programmable packet filtering (unicast, multicast, broadcast)
  • CRC generation and checking in hardware
  • Loopback mode for diagnostics

Applications

  • Embedded Ethernet connectivity for MCU without MAC
  • IoT device network interface
  • Industrial automation Ethernet nodes
  • Home automation web server
Product Introduction: ENC28J60-I/SS Product Introduction

The ENC28J60-I/SS from Microchip Technology is a standalone 10 Mbps Ethernet controller that provides a complete Ethernet interface for microcontrollers lacking an integrated MAC. The device integrates both the MAC (Media Access Controller) and 10Base-T PHY (Physical Layer Transceiver) in a single chip, requiring only an external Ethernet magnetics (RJ-45 with built-in transformer) and a few passive components. The SPI host interface (up to 20 MHz) provides a simple 4-wire connection to any microcontroller. The 8 KB dual-port SRAM buffer allows the host MCU to read/write Ethernet packets while the controller processes the next frame. Hardware features include automatic polarity correction, programmable packet filtering, CRC generation/checking, and loopback mode for testing. The device is widely used in Arduino Ethernet shields and embedded IoT projects.

Working Principle: ENC28J60-I/SS Working Principle

The ENC28J60-I/SS operates as a SPI peripheral where the host MCU reads and writes internal control registers and buffer memory through the SPI interface. For transmission, the MCU writes the Ethernet frame data into the TX buffer area of the 8 KB SRAM, sets the TX control registers, and triggers transmission. The MAC layer adds the preamble and start-of-frame delimiter, computes and appends the CRC, and passes the frame to the PHY layer for 10Base-T Manchester encoding and transmission on the twisted-pair cable. For reception, the PHY decodes incoming Manchester-encoded data, the MAC verifies the preamble and CRC, applies programmable packet filters (unicast, multicast, broadcast, pattern match), and stores valid frames in the RX buffer area. The MCU is notified via an interrupt pin (INT) when a packet is received. The 8 KB SRAM is divided between TX and RX buffers with configurable boundaries. The two LED pins can be configured to indicate link status and network activity.

Pin Description: ENC28J60-I/SS Pin Definition and Functions
Pin Group Name Type Function
Dedicated CS/SCK/SI/SO I/O SPI interface
Dedicated INT Output Interrupt (active LOW)
Dedicated WOL Output Wake-on-LAN interrupt
Dedicated CLKOUT Output Programmable clock output
Dedicated TPIN+/TPIN- Input Receive differential pair
Dedicated TPOUT+/TPOUT- Output Transmit differential pair
Dedicated LEDA/LEDB Output LED outputs (Link/Activity)
Dedicated VDD/VSS Power 3.3V supply and ground
Dedicated RESET Input Hardware reset (active LOW)
Application Scenarios: In which products and applications is ENC28J60-I/SS used
  • Arduino Ethernet shield with SPI interface for web server
  • Industrial sensor network node with 10Mbps Ethernet connectivity
  • Home automation controller with ENC28J60 web interface
  • Smart meter data concentrator with SPI-to-Ethernet bridge
Alternative Models: What chips are recommended as replacements for ENC28J60-I/SS
Manufacturer Part Number Package Notes
Microchip ENC424J600-I/PT TQFP-44 10/100Mbps, parallel+SPI, upgrade
WIZnet W5100S-L LQFP-48 10/100Mbps, hardware TCP/IP stack
WIZnet W5500 LQFP-48 10/100Mbps, hardware TCP/IP, popular
Silicon Labs CP2200-A-GM QFN-28 10Mbps, similar class
Microchip KSZ8851SNL QFN-32 10/100Mbps, SPI, upgrade path

Recommend Parts

0751.0505

Schurter fuse, 0751.0505

Brand: schurter

Package: See datasheet

IN STOCK: 6768pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TL062CDR

Low-power JFET-input dual op-amp, 1MHz GBW, 30pA Ibias, SOIC-8, ±3.5V to ±18V

Brand: TI

Package: SOIC-8 (3.9 x 4.9 x 1.75mm)

IN STOCK: 11576pcs

Cargo cycle: 3-7 Days

The minimum order is 1

P89LPC922FN

8-bit 80C51 MCU, 8KB Flash, 256B RAM, 20-SSOP

Brand: NXP

Package: SSOP-20 (7.2 x 5.3 mm)

IN STOCK: 12628pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AC0603JR-070RL

Chip Resistor, 0Ω (Zero Ohm Jumper), ±5%, 0603 (1608 Metric), 1/10W (100mW)

Brand: Yageo

Package: 0603 (1608 Metric)

IN STOCK: 100000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LMR34206FSC5RNXRQ1

42V 2A sync buck, 5V fixed, 2.2MHz, 18uA Iq, AEC-Q100, SOT-563

Brand: TI

Package: SOT-563 (1.6 x 1.2 x 0.55mm)

IN STOCK: 6500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AO3402

30V N-channel trench MOSFET, SOT-23, 4A, RDS(on) 52m ohm max @ 10V, Qg 10nC, 2.5V gate drive capable, -55C to +150C.

Brand: aosmd

Package: SOT-23 (2.9 x 1.6 x 1.25mm)

IN STOCK: 14066pcs

Cargo cycle: 3-7 Days

The minimum order is 1