Opens in a new tab

MCP6541T-I/OT

Single Comparator, 600nA Iq, Push-Pull RRIO, SOT-23-5, AEC-Q100

8765

Effective Inventory

Image for reference only

Manufacturer Part:

MCP6541T-I/OT

Package:

SOT-23-5 (2.9 x 1.6 x 1.0 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The MCP6541T-I/OT from Microchip Technology is a single-channel push-pull output sub-microamp comparator with 600 nA quiescent current, rail-to-rail input, and 4 us propagation delay in a SOT-23-5 package.

Key Specifications

Type Single Push-Pull Output Sub-Microamp Comparator
Channels 1
Supply Voltage 1.6 V to 5.5 V
Quiescent Current 600 nA (typical)
Propagation Delay 4 us (typical @ 100mV overdrive)
Input Offset Voltage +/-1.5 mV (typical), +/-7 mV (max)
Input Bias Current 1 pA (typical)
Input Hysteresis 3.3 mV (typical)
CMRR 70 dB (typical)
Output Push-Pull (CMOS/TTL compatible)
Package SOT-23-5
Operating Temperature -40C to +85C (I grade)

Features

  • Ultra-low 600 nA quiescent current
  • Rail-to-rail input range (VSS-0.3V to VDD+0.3V)
  • Push-pull CMOS/TTL output
  • 4 us propagation delay
  • 3.3 mV internal hysteresis for noise immunity
  • 1 pA input bias current (CMOS input)
  • AEC-Q100 Grade 1 qualified

Applications

  • Battery-powered voltage monitoring
  • Window comparator circuits
  • RC oscillator and timer
  • Alarm and monitoring systems
Product Introduction: MCP6541T-I/OT Product Introduction

The MCP6541T-I/OT from Microchip Technology is a single-channel push-pull output comparator optimized for ultra-low-power applications. The 600 nA typical quiescent current enables years of battery operation in always-on monitoring circuits. The rail-to-rail input range extends 300 mV beyond both supply rails, accommodating the full input common-mode range without phase reversal. The push-pull output stage swings rail-to-rail, directly driving CMOS and TTL logic inputs without pull-up resistors. The 3.3 mV internal hysteresis prevents output oscillation due to input noise, which is critical for slowly-varying signals. The 1 pA input bias current preserves high-impedance source accuracy. The 4 us propagation delay supports moderate-speed applications. The AEC-Q100 Grade 1 qualification enables automotive use. The SOT-23-5 package provides a minimal footprint.

Working Principle: MCP6541T-I/OT Working Principle

The MCP6541T-I/OT uses a CMOS input stage that provides the 1 pA input bias current and rail-to-rail common-mode range. The input stage is followed by a high-gain differential amplifier that compares the IN+ and IN- voltages. When IN+ exceeds IN- by more than the offset voltage plus hysteresis, the output drives to VDD (logic HIGH). When IN- exceeds IN+ by the same threshold, the output drives to VSS (logic LOW). The 3.3 mV internal hysteresis creates two distinct switching thresholds: a higher threshold for positive-going inputs and a lower threshold for negative-going inputs. This hysteresis window prevents the output from chattering when the input signal slowly crosses the threshold or has noise superimposed. The push-pull CMOS output stage uses complementary P-channel and N-channel transistors to actively drive the output to both VDD and VSS, unlike open-drain comparators that require an external pull-up resistor. The 600 nA quiescent current is achieved by operating the internal amplifier at very low bias currents, which limits the bandwidth and results in the 4 us propagation delay.

Pin Description: MCP6541T-I/OT Pin Definition and Functions
Pin Name Type Function
1 VDD Power Positive supply (1.6-5.5V)
2 IN- Input Inverting input
3 IN+ Input Non-inverting input
4 VSS Power Ground / negative supply
5 OUT Output Push-pull output
Application Scenarios: In which products and applications is MCP6541T-I/OT used
  • Battery voltage monitor with 600nA always-on current and push-pull output to MCU GPIO
  • Window comparator using 2x MCP6541 for over/undervoltage alarm
  • RC relaxation oscillator at 1kHz for system tick with 600nA average current
  • Capacitive touch sensor threshold detector with 1pA input bias current
Alternative Models: What chips are recommended as replacements for MCP6541T-I/OT
Manufacturer Part Number Package Notes
Microchip MCP6541T-E/OT SOT-23-5 Extended temp -40~125C version
TI TLV3491AIDBVR SOT-23-5 Push-pull, 1.8uA, similar class
Microchip MCP6541RT-I/OT SOT-23-5 Automotive grade version
Microchip MCP6541T-I/SN SOIC-8 Same function, SOIC-8 package
Maxim MAX9031AKA+T SOT-23-5 Push-pull, 0.5uA, alternative

Recommend Parts

0751.0505

Schurter fuse, 0751.0505

Brand: schurter

Package: See datasheet

IN STOCK: 6768pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TL062CDR

Low-power JFET-input dual op-amp, 1MHz GBW, 30pA Ibias, SOIC-8, ±3.5V to ±18V

Brand: TI

Package: SOIC-8 (3.9 x 4.9 x 1.75mm)

IN STOCK: 11576pcs

Cargo cycle: 3-7 Days

The minimum order is 1

P89LPC922FN

8-bit 80C51 MCU, 8KB Flash, 256B RAM, 20-SSOP

Brand: NXP

Package: SSOP-20 (7.2 x 5.3 mm)

IN STOCK: 12628pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AC0603JR-070RL

Chip Resistor, 0Ω (Zero Ohm Jumper), ±5%, 0603 (1608 Metric), 1/10W (100mW)

Brand: Yageo

Package: 0603 (1608 Metric)

IN STOCK: 100000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LMR34206FSC5RNXRQ1

42V 2A sync buck, 5V fixed, 2.2MHz, 18uA Iq, AEC-Q100, SOT-563

Brand: TI

Package: SOT-563 (1.6 x 1.2 x 0.55mm)

IN STOCK: 6500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AO3402

30V N-channel trench MOSFET, SOT-23, 4A, RDS(on) 52m ohm max @ 10V, Qg 10nC, 2.5V gate drive capable, -55C to +150C.

Brand: aosmd

Package: SOT-23 (2.9 x 1.6 x 1.25mm)

IN STOCK: 14066pcs

Cargo cycle: 3-7 Days

The minimum order is 1