Opens in a new tab

INA219BIDCN

Bidirectional current/power monitor, I2C, 0-26V CMV, 0.1% gain error, SOT-23-8

8920

Effective Inventory

Image for reference only

Manufacturer Part:

INA219BIDCN

Package:

SOT-23-8 (2.9 x 2.8 x 1.45mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The INA219BIDCN is a bidirectional current/power monitor with I2C interface from Texas Instruments featuring 0.1% gain error, 16 programmable addresses, and 12-bit ADC in a tiny SOT-23-8 package.

Key Specifications

Supply Voltage 3V to 5.5V
Common-Mode Voltage 0V to 26V
Gain Error 0.1% (max)
Offset Voltage 100 µV (max)
ADC Resolution 12-bit
Interface I2C (up to 1MHz fast mode plus)
I2C Addresses 16 programmable via A0/A1 pins
Shunt Voltage Range ±320mV (PGA gain = /1)
Operating Current 1mA maximum
Operating Temperature -40°C to +125°C
Package SOT-23-8

Features

  • High-precision 0.1% gain error over temperature
  • Wide common-mode voltage range: 0V to 26V
  • 16 programmable I2C addresses for multi-sensor systems
  • Bidirectional current measurement capability
  • 12-bit ADC with programmable resolution and conversion time
  • Internal multiplier for direct power calculation
  • Alert pin with programmable over-limit threshold
  • Low quiescent current: 1mA max

Applications

  • Battery chargers and fuel gauges
  • Power supply monitoring
  • Server and telecom power management
  • Motor control current sensing
  • Solar and renewable energy systems
Product Introduction: INA219BIDCN Product Introduction

The INA219BIDCN is a high-side bidirectional current shunt and power monitor from Texas Instruments with an I2C interface. It features 0.1% gain error accuracy, a wide 0V to 26V common-mode voltage range, and a 12-bit ADC with programmable resolution (9 to 12 bits). The device measures shunt voltage, bus voltage, and internally calculates power, providing all data via the I2C interface. The 16 programmable I2C addresses allow up to 16 devices on a single bus. An alert pin with programmable threshold provides hardware interrupt capability for over-current or over-power conditions. The B-grade version offers improved 0.1% gain error specification over the A-grade.

Working Principle: INA219BIDCN Working Principle

The INA219BIDCN operates as a delta-sigma ADC-based current and power monitor. The shunt voltage across the external sense resistor is amplified by the programmable gain amplifier (PGA) with gains of /1, /2, /4, or /8, providing full-scale ranges of ±320mV, ±160mV, ±80mV, or ±40mV respectively. The ADC converts the amplified shunt voltage and the bus voltage using a delta-sigma architecture with programmable resolution and conversion time (9 to 12 bits, 84µs to 68.1ms). An internal multiplier circuit automatically computes the power value by multiplying the shunt current (derived from shunt voltage and programmed calibration value) by the bus voltage. The calibration register allows the user to set the current LSB to any desired value, enabling direct readout in amperes and watts. The I2C interface provides access to all measurement registers, configuration, and alert threshold settings. The alert comparator monitors selected parameters and asserts the ALERT pin when thresholds are exceeded.

Pin Description: INA219BIDCN Pin Definition and Functions
Pin Name Type Description
1 IN+ Analog Input Positive shunt voltage input (connect to load side)
2 IN- Analog Input Negative shunt voltage input (connect to supply side)
3 GND Power Ground
4 SDA I/O I2C data (open drain)
5 SCL Input I2C clock
6 A0 Input I2C address select bit 0 (connect to GND, VS, SDA, or SCL)
7 A1 Input I2C address select bit 1 (connect to GND, VS, SDA, or SCL)
8 VS Power Supply voltage (3V-5.5V)
Application Scenarios: In which products and applications is INA219BIDCN used
  • Battery Management: Bidirectional current measurement with 0.1% accuracy tracks charge and discharge cycles in battery packs
  • Server Power Monitoring: 0-26V CMV range covers 12V and 5V rails; 16 addresses enable multi-rail monitoring
  • Solar Energy: Power calculation eliminates need for external MCU multiplication; alert pin flags over-current
  • Motor Control: Bidirectional capability measures both drive and regenerative currents in H-bridge motor drivers
  • Test Equipment: Programmable gain and calibration enable flexible current ranges from milliamps to amps
Alternative Models: What chips are recommended as replacements for INA219BIDCN
Model Manufacturer Key Difference Package Specs
INA219AIDCN TI A-grade, 1% gain error, lower cost – –
INA226 TI Higher precision (0.1%), 16-bit, alert pin, MSOP-10 – –
INA260 TI Integrated 2mΩ shunt, no external resistor needed – –
MAX34417 ADI/Maxim Quad channel, 12-bit, I2C – –
PAC1710-1-AIA Microchip Single-supply, 0-40V, I2C – –

Recommend Parts

MCP6S26-I

6-channel PGA, SPI interface, gains 1-32V/V, 10MHz BW, rail-to-rail, 2.5-5.5V, SOIC-14

Brand: MICROCHIP

Package: SOIC-14 (150 mils body width)

IN STOCK: 6800pcs

Cargo cycle: 3-7 Days

The minimum order is 1

W25Q80VSSI

8Mbit Serial Flash, Quad SPI, 104MHz, SOIC-8, 2.7-3.6V

Brand: Winbond

Package: SOIC-8 208mil (5.3×8.0mm)

IN STOCK: 4316pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MM3Z9V1

9.1V 200mW Zener diode, SOD-323, onsemi/Diotec

Brand: ON

Package: SOD-323 (2.5 x 1.25 x 0.85 mm)

IN STOCK: 10735pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AT89S51

8-bit 8051 MCU, 4KB ISP Flash, 128B RAM, 32 I/O, 2 timers, UART, watchdog timer, dual DPTR, 33MHz, ISP programming, PDIP-40, Atmel AT89S51.

Package: PDIP-40 / TQFP-44 / PLCC-44

IN STOCK: 15000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

GD32F303CBT6

Cortex-M4 32-bit MCU, 120MHz, 128KB Flash, 32KB SRAM, LQFP-48

Brand: gigadevice

Package: LQFP-48 (7x7mm, 0.5mm pitch)

IN STOCK: 3342pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MIC5205-3.3YM5-TR

3.3V 150mA ultra-low-noise LDO, 165mV dropout, 30uVrms noise, SOT-23-5

Brand: MICROCHIP

Package: SOT-23-5 (2.9 x 1.6 x 1.1mm)

IN STOCK: 9858pcs

Cargo cycle: 3-7 Days

The minimum order is 1