Opens in a new tab

LM393DR

Dual comparator, open-collector, 2-36V, 1.3µs, SOIC-8

22000

Effective Inventory

Image for reference only

Manufacturer Part:

LM393DR

Package:

SOIC-8 (4.9 x 3.91 x 1.58mm, 1.27mm pitch)

Brand:

Product Categories:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The LM393DR is a dual differential comparator from Texas Instruments with open-collector outputs, low offset voltage, and single/dual supply operation in an SOIC-8 package.

Key Specifications

Number of Comparators 2 (dual)
Supply Voltage Range 2V to 36V (single) or ±1V to ±18V (dual)
Input Offset Voltage 1mV typical, 5mV max
Input Bias Current 25nA typical
Input Common-Mode Range 0V to VCC-1.5V
Output Type Open-collector (requires pull-up resistor)
Output Sink Current 16mA typical
Response Time 1.3µs typical (5mV overdrive)
Supply Current 0.4mA typical (both comparators)
Operating Temperature 0°C to +70°C
Package SOIC-8 (4.9 x 3.91mm)

Features

  • Dual independent comparators in single 8-pin package
  • Open-collector outputs for wire-OR and level shifting
  • Wide supply range: 2V to 36V single supply
  • Low input offset voltage: 1mV typical
  • Input common-mode range includes ground
  • 1.3µs response time at 5mV overdrive
  • Low 0.4mA total supply current
  • Output compatible with TTL, MOS, and CMOS

Applications

  • Voltage threshold detection
  • Zero-crossing detection
  • Window comparators
  • Oscillator and timing circuits
  • Level shifting and interface
Product Introduction: LM393DR Product Introduction

The LM393DR from Texas Instruments contains two independent voltage comparators in an 8-pin SOIC package. Each comparator compares the voltage at its non-inverting input (+) against the voltage at its inverting input (-) and drives an open-collector output LOW when the + input is below the – input, and HIGH (floating/open) when the + input exceeds the – input. The open-collector output requires an external pull-up resistor and can be wire-ORed with other LM393 outputs or connected to a different voltage rail for level shifting. The device operates from a single 2V to 36V supply or dual ±1V to ±18V supplies, with only 0.4mA total quiescent current. The input common-mode range extends from ground to VCC-1.5V, allowing ground-referenced sensing. The 1.3µs response time at 5mV overdrive is suitable for moderate-speed applications. The DR suffix denotes the SOIC-8 package with tape-and-reel packaging.

Working Principle: LM393DR Working Principle

Each of the two comparators in the LM393DR continuously monitors the voltage difference between its non-inverting (+) and inverting (-) inputs. When V+ > V-, the output transistor is OFF and the open-collector output floats (pulled HIGH by the external pull-up resistor). When V+ < V-, the output transistor turns ON and sinks current to ground, pulling the output LOW. The open-collector configuration provides several advantages: (1) multiple outputs can be wire-ORed by connecting them together with a single pull-up resistor, creating a logical AND function (any comparator pulling LOW pulls the entire line LOW); (2) the pull-up voltage can be different from the comparator supply voltage, enabling level shifting from a 5V comparator output to a 3.3V or 12V logic input; (3) the output can directly drive relay coils or LEDs with the pull-up connected to the load supply. The 1mV typical input offset voltage means the switching threshold is accurate to within 1mV of the actual comparison point. The 1.3µs response time at 5mV overdrive indicates the time from the input crossing the threshold to the output reaching 50% of its final value.

Pin Description: LM393DR Pin Definition and Functions
Pin Name Type Description
1 1OUT Output Comparator 1 output (open-collector)
2 1IN- Input Comparator 1 inverting input
3 1IN+ Input Comparator 1 non-inverting input
4 GND Power Ground / negative supply
5 2IN+ Input Comparator 2 non-inverting input
6 2IN- Input Comparator 2 inverting input
7 2OUT Output Comparator 2 output (open-collector)
8 VCC Power Positive supply (2V to 36V)

LM393DR uses the SOIC-8 (D) surface-mount package with standard dual comparator pinout: Pin 1 = Output A (open-collector), Pin 2 = Inverting Input A (-), Pin 3 = Non-inverting Input A (+), Pin 4 = GND, Pin 5 = Non-inverting Input B (+), Pin 6 = Inverting Input B (-), Pin 7 = Output B (open-collector), Pin 8 = VCC. The DR suffix denotes SOIC-8 tape-and-reel from TI. Open-collector outputs require external pull-up resistors. The SOIC-8 pinout is identical to the PDIP-8 version (LM393N), enabling seamless PCB layout migration between through-hole and surface-mount. Operating voltage range is 2V-36V single supply or ±1V-±18V dual supply.

Application Scenarios: In which products and applications is LM393DR used
  • Threshold Detect: Compare sensor voltage against a reference; open-collector directly drives MCU interrupt or LED indicator
  • Window Comparator: Two comparators + 3 resistors create an in-range/out-of-range detector for voltage monitoring
  • Zero-Cross: Compare AC signal against ground reference for synchronization in TRIAC dimmer circuits
  • Level Shift: Pull-up to different voltage (e.g., 3.3V) while comparator runs on 12V supply
  • Wire-OR: Multiple comparators share one pull-up; any threshold violation pulls the line LOW for fault aggregation
Alternative Models: What chips are recommended as replacements for LM393DR
Model Manufacturer Key Difference Package Specs
LM393AN TI Improved version with lower 2mV max offset voltage for precision threshold detection circuits DIP-8 1.3µs/2-36V
LM2903N TI Automotive-grade -40 to +125C version for under-hood and industrial comparator applications DIP-8 1.3µs/-40-125C
LM339N TI Quad comparator version (4 channels) in DIP-14 for multi-channel threshold detection DIP-14 1.3µs/4-ch
TLV3202AIDR TI High-speed 40ns dual comparator with push-pull output for fast signal detection SOIC-8 40ns/2.7-5.5V
LTC6702IS8 ADI Micro-power 18-bit configurable comparator with 200nA supply for battery monitoring SOIC-8 18-bit/200nA

LM393 is the industry-standard dual voltage comparator with open-drain output and 2-36V supply range. The 1.3µs response time suits general-purpose threshold detection. LM393AN offers lower offset voltage. LM339 provides 4 comparators in DIP-14. For high-speed applications, TLV3202 offers 40ns response with push-pull output at 2.7-5.5V supply.

Recommend Parts

MSP432P401RIPZR

Ultra-low-power Cortex-M4F MCU, 48MHz, 256KB Flash, 14-bit ADC, 850nA standby, 100-LQFP

Brand: TI

Package: 100-LQFP (14 x 14 x 1.4mm)

IN STOCK: 3750pcs

Cargo cycle: 3-7 Days

The minimum order is 1

PTN78060WAH

4.5A positive-input buck-IT module, adjustable, SMD module

Brand: TI

Package: Module (34.3 x 19.3 x 8.2 mm)

IN STOCK: 4786pcs

Cargo cycle: 3-7 Days

The minimum order is 1

PIC16F1526-I/PT

8-bit PIC16 MCU, 14KB Flash, 768B RAM, 30-ch 10-bit ADC, 10x CCP, 64-TQFP, XLP

Brand: MICROCHIP

Package: TQFP-64 (10.0 x 10.0 x 1.05 mm)

IN STOCK: 5600pcs

Cargo cycle: 3-7 Days

The minimum order is 1

R2A20178NP

8-channel 8-bit voltage output DAC, R-2R architecture, buffered rail-to-rail output, SPI interface up to 25MHz, 2.7-5.5V

Brand: Renesas

Package: 24-pin HWQFN (4x4x0.75mm)

IN STOCK: 6399pcs

Cargo cycle: 3-7 Days

The minimum order is 1

VS-40CPQ100-N3

Dual Schottky rectifier, common cathode, 2x20A, 100V, 0.61V VF, TO-247AC-3L, Vishay Q-series, 175 degC TJ, guard ring

Brand: VISHAY

Package: TO-247AC 3L (3-lead through-hole, 15.5mm width, tab for heatsink, common cathode configuration)

IN STOCK: 8950pcs

Cargo cycle: 3-7 Days

The minimum order is 1

BSC040N10NS5

OptiMOS 5 N-ch 100V 4mΩ 136A MOSFET, SuperSO8

Brand: infineon

Package: PG-TDSON-8 (SuperSO8, 5 x 6mm)

IN STOCK: 10509pcs

Cargo cycle: 3-7 Days

The minimum order is 1