Opens in a new tab

SN74HC14N

Hex Schmitt-trigger inverter, 2-6V HC CMOS, hysteresis, PDIP-14

6500

Effective Inventory

Image for reference only

Manufacturer Part:

SN74HC14N

Package:

PDIP-14 (19.3 x 6.35 x 4.57mm, 2.54mm pitch, through-hole)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The SN74HC14N from Texas Instruments is a hex Schmitt-trigger inverter with CMOS technology, wide supply range (2V to 6V), hysteresis for noise immunity, and 17ns propagation delay in a 14-pin PDIP package.

Key Specifications

Number of Gates 6 (hex inverter with Schmitt trigger)
Logic Family HC (High-speed CMOS)
Supply Voltage 2V to 6V
Input Threshold HIGH (VT+) 3.15V min @ VCC=4.5V
Input Threshold LOW (VT-) 0.9V max @ VCC=4.5V
Hysteresis (VT+ – VT-) 0.8V min @ VCC=4.5V
Propagation Delay 17ns typical @ VCC=5V
Output Drive (IOL/IOH) 4mA / -4mA @ VCC=4.5V
Operating Temperature -40°C to +85°C
Package PDIP-14 (19.3 x 6.35mm)

Features

  • Six Schmitt-trigger inverters
  • Wide supply voltage: 2V to 6V
  • Input hysteresis for noise immunity
  • Slow input edge tolerance (no oscillation)
  • 17ns propagation delay at 5V
  • 4mA output drive at 4.5V

Applications

  • Square wave oscillator (RC)
  • Signal conditioning and debouncing
  • Slow edge to fast edge conversion
  • Level translation (with resistors)
  • Power-on reset generation
Product Introduction: SN74HC14N Product Introduction

The SN74HC14N from Texas Instruments is a hex Schmitt-trigger inverter—six independent inverting buffers with hysteresis on each input. The Schmitt-trigger input provides two distinct threshold voltages: a higher threshold (VT+) for rising inputs and a lower threshold (VT-) for falling inputs. This hysteresis (minimum 0.8V at 4.5V supply) makes the device immune to noise on slowly changing signals, preventing the output oscillation that would occur with a standard inverter. This makes the 74HC14 the go-to device for cleaning up noisy signals, debouncing mechanical switches, and generating clock signals from RC oscillators. The 2V to 6V supply range makes it compatible with both 3.3V and 5V systems. The N suffix denotes the PDIP-14 through-hole package.

Working Principle: SN74HC14N Working Principle

The SN74HC14N’s Schmitt-trigger inputs use positive feedback to create two switching thresholds. When the input voltage rises from LOW to HIGH, the output does not switch until the input exceeds VT+ (approximately 2.4V at VCC=4.5V). Once the output switches LOW, the positive feedback lowers the effective threshold to VT- (approximately 1.4V at VCC=4.5V). The input must now drop below VT- before the output switches back HIGH. This hysteresis band (VT+ – VT- ≈ 1V) means that noise or ringing on the input that is smaller than the hysteresis cannot cause false switching. In an RC oscillator, one Schmitt inverter with a resistor from output to input and a capacitor from input to ground creates a free-running square wave: the capacitor charges through the resistor until VT+ is reached, the output goes LOW, the capacitor discharges until VT- is reached, and the cycle repeats. The oscillation frequency is approximately f = 1/(0.8 × R × C). Without hysteresis, a standard inverter in this configuration would latch at its linear bias point rather than oscillate.

Pin Description: SN74HC14N Pin Definition and Functions
Pin Name Type Description
1 1A Input Inverter 1 input (Schmitt trigger)
2 1Y Output Inverter 1 output
3 2A Input Inverter 2 input
4 2Y Output Inverter 2 output
5 3A Input Inverter 3 input
6 3Y Output Inverter 3 output
7 GND Power Ground
8 4Y Output Inverter 4 output
9 4A Input Inverter 4 input
10 5Y Output Inverter 5 output
11 5A Input Inverter 5 input
12 6Y Output Inverter 6 output
13 6A Input Inverter 6 input
14 VCC Power Supply (2V to 6V)

SN74HC14N uses the PDIP-14 package with the same hex inverter pinout as 7404/74LS04/74HC04: VCC at Pin 14, GND at Pin 7. Six independent Schmitt-trigger inverters: Inv 1 (Pin 1 in, Pin 2 out), Inv 2 (Pin 3 in, Pin 4 out), Inv 3 (Pin 5 in, Pin 6 out), Inv 4 (Pin 9 in, Pin 8 out), Inv 5 (Pin 11 in, Pin 10 out), Inv 6 (Pin 13 in, Pin 12 out). The Schmitt-trigger hysteresis is typically 0.9V at 4.5V supply (VT+ ≈ 2.85V, VT- ≈ 1.95V). This hysteresis cleans up slow edges from sensors, switches, and RC oscillators. For CMOS 4000-series equivalent, CD40106BE provides wider supply range (3-15V) with proportional hysteresis.

Application Scenarios: In which products and applications is SN74HC14N used
  • RC Oscillator: 1 inverter + R (10kΩ) + C (10nF) ≈ 1.25kHz clock; clean 50% duty cycle square wave
  • Switch Debounce: Mechanical switch to input via 10kΩ pull-up + 100nF cap; hysteresis eliminates bounce
  • Signal Cleanup: Noisy sensor signal through 74HC14; hysteresis removes glitches; output is clean digital
  • Level Shift: 3.3V signal through 74HC14 at VCC=5V; input compatible with 3.3V logic; output is 5V CMOS
  • Power-On Reset: RC network on input; capacitor charges slowly; output stays HIGH (inverted LOW input) during power-up
Alternative Models: What chips are recommended as replacements for SN74HC14N
Model Manufacturer Key Difference Package Supply
74LS14N TI/Nexperia Original TTL version with 5V-only supply, typical propagation delay 10-15ns DIP-14 5V TTL
74LS14D TI/Nexperia Surface-mount SOIC version of LS with identical logic function SOIC-14 5V TTL
74HC14D TI/Nexperia CMOS version with wide 2-6V supply range, lower power consumption and higher noise immunity SOIC-14 2-6V CMOS
74HC14N TI/Nexperia Through-hole DIP version of HC family for prototyping and repair DIP-14 2-6V CMOS
74HCT14D TI/Nexperia CMOS with TTL-compatible input levels, ideal for mixing with LS devices at 5V SOIC-14 4.5-5.5V TTL-in
74HCT14N TI/Nexperia Through-hole DIP version of HCT family for prototyping and repair DIP-14 4.5-5.5V TTL-in
74AC14D TI/Nexperia Advanced CMOS with 2-6V supply and higher output drive current (24mA vs 6mA for HC) SOIC-14 2-6V CMOS
74AC14N TI/Nexperia Through-hole DIP version of AC family for prototyping and repair DIP-14 2-6V CMOS
74LVC14D TI/Nexperia Low-voltage CMOS for 1.65-3.6V modern logic with 24mA output drive and bus-hold inputs SOIC-14 1.65-3.6V CMOS
74LVC14N TI/Nexperia Through-hole DIP version of LVC family for prototyping and repair DIP-14 1.65-3.6V CMOS

The 7414 is a Hex Schmitt-Trigger Inverter. Family variants span from the original LS TTL (5V only) to modern LVC/AUP (down to 0.8V). HC and HCT versions offer 2-6V CMOS operation with HCT providing TTL-compatible input thresholds for mixed 5V systems. CD4000-series equivalents offer the widest 3-18V supply range at the cost of lower switching speed. DIP packages (N suffix) are through-hole; SOIC (D suffix) and TSSOP are surface-mount.

Recommend Parts

0751.0505

Schurter fuse, 0751.0505

Brand: schurter

Package: See datasheet

IN STOCK: 6768pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TL062CDR

Low-power JFET-input dual op-amp, 1MHz GBW, 30pA Ibias, SOIC-8, ±3.5V to ±18V

Brand: TI

Package: SOIC-8 (3.9 x 4.9 x 1.75mm)

IN STOCK: 11576pcs

Cargo cycle: 3-7 Days

The minimum order is 1

P89LPC922FN

8-bit 80C51 MCU, 8KB Flash, 256B RAM, 20-SSOP

Brand: NXP

Package: SSOP-20 (7.2 x 5.3 mm)

IN STOCK: 12628pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AC0603JR-070RL

Chip Resistor, 0Ω (Zero Ohm Jumper), ±5%, 0603 (1608 Metric), 1/10W (100mW)

Brand: Yageo

Package: 0603 (1608 Metric)

IN STOCK: 100000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LMR34206FSC5RNXRQ1

42V 2A sync buck, 5V fixed, 2.2MHz, 18uA Iq, AEC-Q100, SOT-563

Brand: TI

Package: SOT-563 (1.6 x 1.2 x 0.55mm)

IN STOCK: 6500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AO3402

30V N-channel trench MOSFET, SOT-23, 4A, RDS(on) 52m ohm max @ 10V, Qg 10nC, 2.5V gate drive capable, -55C to +150C.

Brand: aosmd

Package: SOT-23 (2.9 x 1.6 x 1.25mm)

IN STOCK: 14066pcs

Cargo cycle: 3-7 Days

The minimum order is 1