Opens in a new tab

NE555P

Precision timer, astable/monostable, 200mA output, 4.5-16V, PDIP-8

20000

Effective Inventory

Image for reference only

Manufacturer Part:

NE555P

Package:

PDIP-8 (9.81 x 6.35 x 5.08mm, 2.54mm pitch, through-hole)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The NE555P from Texas Instruments is the industry-standard precision timer IC capable of producing accurate time delays from microseconds to hours, operating in astable or monostable mode with a 200mA output in a PDIP-8 package.

Key Specifications

Supply Voltage 4.5V to 16V
Output Current 200mA sink/source
Trigger Level 1/3 VCC (approximately)
Threshold Level 2/3 VCC (approximately)
Timing Accuracy ±1% typical (with quality R/C)
Maximum Frequency (astable) ~500kHz
Monostable Pulse Width 1.1 × R × C
Astable Frequency 1.44 / ((R1 + 2×R2) × C)
Astable Duty Cycle (R1 + R2) / (R1 + 2×R2) × 100%
Supply Current 2-6mA typical
Reset Active Level LOW (overrides all other inputs)
Control Voltage 2/3 VCC (can be modulated)
Operating Temperature 0°C to +70°C
Package PDIP-8 (9.81 x 6.35mm)

Features

  • Timing from microseconds to hours
  • Astable or monostable operation
  • Adjustable duty cycle
  • 200mA output — can directly drive relays, LEDs, speakers
  • TTL-compatible output at 5V supply
  • Control voltage pin for modulation
  • Reset overrides all other inputs

Applications

  • Pulse generation and timing
  • LED flasher and oscillator
  • Delay timer circuits
  • PWM controller
  • Tone generator and buzzer driver
Product Introduction: NE555P Product Introduction

The NE555P from Texas Instruments is the original and most iconic timer IC, designed by Hans Camenzind at Signetics in 1971 and still in active production. It can operate in two fundamental modes: monostable (one-shot) produces a single pulse of precise duration t = 1.1×R×C when triggered; astable (free-running) generates a continuous square wave with frequency f = 1.44/((R1+2R2)×C) and duty cycle = (R1+R2)/(R1+2R2). The 200mA output can directly drive relays, LEDs, small speakers, and TTL/CMOS logic without a buffer. The internal voltage divider sets the trigger at 1/3 VCC and threshold at 2/3 VCC; these levels can be modified through the control voltage pin for PWM or modulation applications. The reset pin (active LOW) overrides all other inputs, forcing the output LOW. The P suffix denotes the PDIP-8 plastic through-hole package.

Working Principle: NE555P Working Principle

The NE555P contains two comparators, an SR flip-flop, a discharge transistor, a resistive voltage divider (three 5kΩ resistors in series from VCC to GND), and an output buffer stage. The voltage divider sets the upper comparator (threshold) reference at 2/3 VCC and the lower comparator (trigger) reference at 1/3 VCC. In monostable mode: initially, the output is LOW and the discharge transistor is ON (shorting the timing capacitor to GND). When the trigger input drops below 1/3 VCC, the lower comparator sets the flip-flop, the output goes HIGH, and the discharge transistor turns OFF. The capacitor charges through the timing resistor R toward VCC. When the capacitor voltage reaches 2/3 VCC, the upper comparator resets the flip-flop, the output goes LOW, and the discharge transistor turns ON, rapidly discharging the capacitor. The output pulse width is t = 1.1×R×C (the factor 1.1 accounts for the ratio of 2/3 VCC and the charging time constant). In astable mode: the capacitor charges through R1+R2 and discharges through R2 only. When charging, the output is HIGH; when the capacitor reaches 2/3 VCC, the output goes LOW and the capacitor discharges through R2. When it reaches 1/3 VCC, the output goes HIGH again. The charge time is 0.693×(R1+R2)×C and the discharge time is 0.693×R2×C. The duty cycle is always >50% because R2 is common to both charge and discharge paths; to achieve 50% duty cycle, a diode across R2 bypasses it during charging.

Pin Description: NE555P Pin Definition and Functions
Pin Name Type Description
1 GND Power Ground
2 TRIG Input Trigger (active LOW; triggers when < 1/3 VCC)
3 OUT Output Output (200mA sink/source)
4 RESET Input Reset (active LOW; forces output LOW; tie to VCC if unused)
5 CONT Input Control voltage (2/3 VCC; bypass with 10nF cap to GND)
6 THRES Input Threshold (resets when > 2/3 VCC)
7 DISCH Output Discharge (open-collector; discharges timing capacitor)
8 VCC Power Supply (4.5V to 16V)

NE555P uses the PDIP-8 package with the classic 555 timer pinout: Pin 1 = GND, Pin 2 = TRIG (trigger, active-low at 1/3 VCC), Pin 3 = OUT (output, can sink/source 200mA), Pin 4 = RESET (active-low override, normally tied to VCC), Pin 5 = CTRL (control voltage, bypass with 10nF to GND for noise immunity), Pin 6 = THR (threshold, triggers at 2/3 VCC), Pin 7 = DISCH (open-collector discharge, connects timing cap to GND), Pin 8 = VCC (4.5-16V). In monostable mode, TRIG (Pin 2) receives the trigger pulse, THR+DISCH (Pins 6+7) connect through the timing resistor to VCC, and the timing capacitor connects from Pins 6+7 to GND. In astable mode, Pins 2+6 are tied together, with two resistors and a capacitor setting the frequency.

Application Scenarios: In which products and applications is NE555P used
  • LED Flasher: Astable: R1=1kΩ, R2=10kΩ, C=10µF; f≈1Hz; 50% duty cycle (with diode across R2); drives LED on pin 3
  • Delay Timer: Monostable: R=1MΩ, C=100µF; t≈110 seconds; push button triggers pin 2; output HIGH for delay period
  • PWM Controller: Astable base frequency; modulate control voltage (pin 5) with audio or control signal; varies pulse width
  • Tone Generator: Astable: R1=1kΩ, R2=10kΩ, C=10nF; f≈1kHz; pin 3 drives speaker through coupling cap
  • Switch Debouncer: Monostable: R=100kΩ, C=1µF; t≈110ms; trigger from switch; output is clean pulse regardless of bounce
Alternative Models: What chips are recommended as replacements for NE555P
Model Manufacturer Key Difference Package Specs
LM555CN TI Direct equivalent with identical timing characteristics and wider -40 to +85C temperature range DIP-8 4.5-16V/200mA
TLC555CP TI CMOS version with 2-15V supply, 1µA typical supply current for battery-powered timers DIP-8 2-15V/100mA CMOS
SA555P TI Automotive-grade -40 to +125C version for under-hood timer and control applications DIP-8 4.5-16V/-40-125C
NA555P TI Wide-temperature -40 to +125C version with military-grade screening for reliability DIP-8 4.5-16V/-40-125C
NE556N TI Dual timer version with two independent 555 timers in a single DIP-14 package DIP-14 4.5-16V/dual
LMC555CN TI CMOS low-power version with 1.5V minimum supply and 2MHz astable frequency capability DIP-8 1.5-15V/100mA

NE555 is the industry-standard precision timer generating accurate time delays from microseconds to hours. It operates in both astable (oscillator) and monostable (one-shot) modes. CMOS versions (TLC555, LMC555) offer 2-15V supply and 1µA standby for battery applications. The NE556 provides dual timers in DIP-14. SA555 extends temperature range to 125C for automotive use.

Recommend Parts

0751.0505

Schurter fuse, 0751.0505

Brand: schurter

Package: See datasheet

IN STOCK: 6768pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TL062CDR

Low-power JFET-input dual op-amp, 1MHz GBW, 30pA Ibias, SOIC-8, ±3.5V to ±18V

Brand: TI

Package: SOIC-8 (3.9 x 4.9 x 1.75mm)

IN STOCK: 11576pcs

Cargo cycle: 3-7 Days

The minimum order is 1

P89LPC922FN

8-bit 80C51 MCU, 8KB Flash, 256B RAM, 20-SSOP

Brand: NXP

Package: SSOP-20 (7.2 x 5.3 mm)

IN STOCK: 12628pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AC0603JR-070RL

Chip Resistor, 0Ω (Zero Ohm Jumper), ±5%, 0603 (1608 Metric), 1/10W (100mW)

Brand: Yageo

Package: 0603 (1608 Metric)

IN STOCK: 100000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LMR34206FSC5RNXRQ1

42V 2A sync buck, 5V fixed, 2.2MHz, 18uA Iq, AEC-Q100, SOT-563

Brand: TI

Package: SOT-563 (1.6 x 1.2 x 0.55mm)

IN STOCK: 6500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AO3402

30V N-channel trench MOSFET, SOT-23, 4A, RDS(on) 52m ohm max @ 10V, Qg 10nC, 2.5V gate drive capable, -55C to +150C.

Brand: aosmd

Package: SOT-23 (2.9 x 1.6 x 1.25mm)

IN STOCK: 14066pcs

Cargo cycle: 3-7 Days

The minimum order is 1