Opens in a new tab

SN74LS112N

Dual J-K flip-flop, negative-edge, preset/clear, PDIP-16

3500

Effective Inventory

Image for reference only

Manufacturer Part:

SN74LS112N

Package:

PDIP-16 (19.3 x 6.35 x 4.57mm, 2.54mm pitch, through-hole)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The SN74LS112N from Texas Instruments is a dual negative-edge-triggered J-K flip-flop with preset and clear inputs, capable of toggle, latch, and shift register functions in a 16-pin PDIP package.

Key Specifications

Number of Flip-Flops 2 (dual, independent)
Logic Family LS (Low-power Schottky)
Trigger Type Negative-edge (falling edge of CLK)
Supply Voltage 4.75V to 5.25V
Max Clock Frequency 30MHz typical
Preset (PRE) Active LOW (asynchronous, sets Q=1)
Clear (CLR) Active LOW (asynchronous, sets Q=0)
Operating Temperature 0°C to +70°C
Package PDIP-16 (19.3 x 6.35mm)

Features

  • Dual J-K flip-flops, negative-edge triggered
  • Asynchronous preset and clear
  • J-K inputs: toggle mode (J=K=1), hold (J=K=0), set (J=1,K=0), reset (J=0,K=1)
  • 30MHz maximum clock frequency

Applications

  • Frequency divider (toggle mode)
  • Shift register building block
  • Counter building block
  • Event latch
Product Introduction: SN74LS112N Product Introduction

The SN74LS112N from Texas Instruments contains two independent negative-edge-triggered J-K flip-flops with asynchronous preset (PRE, active LOW) and clear (CLR, active LOW) inputs. The J-K flip-flop is the most versatile flip-flop type: it can toggle (J=K=1), hold its state (J=K=0), set (J=1, K=0), or reset (J=0, K=1). In toggle mode, the output divides the clock frequency by 2, making it ideal for frequency dividers and binary counter chains. The negative-edge trigger means the output changes on the falling edge of the clock, which is important for cascaded counters where ripple delays must be accommodated. The asynchronous PRE and CLR inputs override the clocked operation: PRE forces Q=1 regardless of J, K, or CLK; CLR forces Q=0. Both PRE and CLR should be HIGH for normal clocked operation. The N suffix denotes the PDIP-16 through-hole package.

Working Principle: SN74LS112N Working Principle

Each J-K flip-flop in the SN74LS112N operates on the falling edge of the clock. The J and K inputs are sampled just before the falling edge, and the output transitions according to: J=0,K=0: Q holds (no change); J=0,K=1: Q goes to 0 (reset); J=1,K=0: Q goes to 1 (set); J=1,K=1: Q toggles (inverts). The setup time requirement means J and K must be stable for at least 20ns before the falling clock edge. The hold time requirement (typically 0ns for LS) means J and K must remain stable for 0ns after the falling edge. In toggle mode (J=K=1), each falling clock edge inverts Q, so the output completes one full cycle for every two clock cycles — a divide-by-2 function. Cascading two toggle flip-flops creates a divide-by-4; three creates divide-by-8, etc. The asynchronous PRE (preset) input forces Q=1 immediately when brought LOW, regardless of the clock. Similarly, CLR (clear) forces Q=0. If both PRE and CLR are LOW simultaneously, both Q and NOT-Q go HIGH (invalid state); the final state after both are released is indeterminate.

Pin Description: SN74LS112N Pin Definition and Functions
Pin Name Type Description
1 1CLK Input Flip-flop 1 clock (falling edge triggered)
2 1K Input Flip-flop 1 K input
3 1J Input Flip-flop 1 J input
4 1PRE Input Flip-flop 1 preset (active LOW, sets Q=1)
5 1Q Output Flip-flop 1 Q output
6 1NOT-Q Output Flip-flop 1 NOT-Q output
7 1CLR Input Flip-flop 1 clear (active LOW, sets Q=0)
8 GND Power Ground
9 2CLR Input Flip-flop 2 clear (active LOW)
10 2NOT-Q Output Flip-flop 2 NOT-Q output
11 2Q Output Flip-flop 2 Q output
12 2PRE Input Flip-flop 2 preset (active LOW)
13 2J Input Flip-flop 2 J input
14 2K Input Flip-flop 2 K input
15 2CLK Input Flip-flop 2 clock (falling edge)
16 VCC Power Supply (5V)
Application Scenarios: In which products and applications is SN74LS112N used
  • Divide-by-2: J=K=1 (tie to VCC); CLK input; Q output = CLK/2; cascaded for divide-by-4, -8, -16…
  • T-Flip-Flop: Same as toggle mode; used for frequency division
  • Data Latch: J=D (data), K=NOT-D; CLK falling edge latches D into Q; D-type flip-flop behavior
  • Shift Register: 1Q connects to 2J; 1NOT-Q to 2K; serial data into 1J/1K; two-stage shift register
Alternative Models: What chips are recommended as replacements for SN74LS112N
Model Manufacturer Key Difference Package Supply
74LS112N TI/Nexperia Original TTL version with 5V-only supply, typical propagation delay 10-15ns DIP-16 5V TTL
74LS112D TI/Nexperia Surface-mount SOIC version of LS with identical logic function SOIC-16 5V TTL
74HC112D TI/Nexperia CMOS version with wide 2-6V supply range, lower power consumption and higher noise immunity SOIC-16 2-6V CMOS
74HC112N TI/Nexperia Through-hole DIP version of HC family for prototyping and repair DIP-16 2-6V CMOS
74HCT112D TI/Nexperia CMOS with TTL-compatible input levels, ideal for mixing with LS devices at 5V SOIC-16 4.5-5.5V TTL-in
74HCT112N TI/Nexperia Through-hole DIP version of HCT family for prototyping and repair DIP-16 4.5-5.5V TTL-in

The 74112 is a Dual Negative-Edge-Triggered J-K Flip-Flop. Family variants span from the original LS TTL (5V only) to modern LVC/AUP (down to 0.8V). HC and HCT versions offer 2-6V CMOS operation with HCT providing TTL-compatible input thresholds for mixed 5V systems. CD4000-series equivalents offer the widest 3-18V supply range at the cost of lower switching speed. DIP packages (N suffix) are through-hole; SOIC (D suffix) and TSSOP are surface-mount.

Recommend Parts

0751.0505

Schurter fuse, 0751.0505

Brand: schurter

Package: See datasheet

IN STOCK: 6768pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TL062CDR

Low-power JFET-input dual op-amp, 1MHz GBW, 30pA Ibias, SOIC-8, ±3.5V to ±18V

Brand: TI

Package: SOIC-8 (3.9 x 4.9 x 1.75mm)

IN STOCK: 11576pcs

Cargo cycle: 3-7 Days

The minimum order is 1

P89LPC922FN

8-bit 80C51 MCU, 8KB Flash, 256B RAM, 20-SSOP

Brand: NXP

Package: SSOP-20 (7.2 x 5.3 mm)

IN STOCK: 12628pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AC0603JR-070RL

Chip Resistor, 0Ω (Zero Ohm Jumper), ±5%, 0603 (1608 Metric), 1/10W (100mW)

Brand: Yageo

Package: 0603 (1608 Metric)

IN STOCK: 100000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LMR34206FSC5RNXRQ1

42V 2A sync buck, 5V fixed, 2.2MHz, 18uA Iq, AEC-Q100, SOT-563

Brand: TI

Package: SOT-563 (1.6 x 1.2 x 0.55mm)

IN STOCK: 6500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AO3402

30V N-channel trench MOSFET, SOT-23, 4A, RDS(on) 52m ohm max @ 10V, Qg 10nC, 2.5V gate drive capable, -55C to +150C.

Brand: aosmd

Package: SOT-23 (2.9 x 1.6 x 1.25mm)

IN STOCK: 14066pcs

Cargo cycle: 3-7 Days

The minimum order is 1