Opens in a new tab

TLVH431IDBZR

1.24V-18V adjustable shunt voltage reference, 1.5% tolerance, 100uA-70mA, SOT-23-3

12000

Effective Inventory

Image for reference only

Manufacturer Part:

TLVH431IDBZR

Package:

3-SOT-23 (2.92 x 1.30 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The TLVH431IDBZR is a Texas Instruments 1.5% low-voltage adjustable precision shunt regulator. It features a 1.24 V reference voltage, adjustable output from 1.24 V to 18 V, 100 µA to 70 mA cathode current range, and 0.25 Ω typical output impedance. The device is packaged in a 3-pin SOT-23 and operates from -40°C to +85°C.

Key Specifications

Reference Voltage 1.24 V (typical)
Initial Accuracy 1.5% (standard grade)
Adjustable Output VREF to 18 V
Cathode Current Range 100 µA to 70 mA
Output Impedance 0.25 Ω (typical)
Package SOT-23-3

Features

  • Low-voltage operation: down to 1.24 V
  • Adjustable output: VREF to 18 V
  • 1.5% reference tolerance (standard grade)
  • 100 µA minimum cathode current
  • 0.25 Ω typical output impedance
  • Sharp turn-on characteristic
  • Lower VREF than TL431 (1.24 V vs 2.5 V)

Applications

  • Isolated feedback for 3.3V SMPS
  • Adjustable voltage reference for converters
  • Low-voltage Zener replacement
  • Voltage monitoring and comparator
Product Introduction: TLVH431IDBZR Product Introduction

The Texas Instruments TLVH431IDBZR is a low-voltage adjustable precision shunt regulator with a 1.24V reference voltage and output adjustable from 1.24V to 18V using two external resistors. The device operates with cathode currents from 100 uA to 70 mA—a significant improvement over the widely used TL431 which requires a minimum 1 mA cathode current—making the TLVH431 suitable for low-power and battery-operated designs. The 1.5% initial reference tolerance (I grade, -40C to +85C) provides adequate accuracy for voltage monitoring and feedback regulation in power supplies. The 0.25 ohm typical dynamic impedance ensures tight regulation under varying load conditions. The lower 1.24V reference voltage (compared to TL431 at 2.495V) enables direct regulation of 3.3V and lower output rails without the resistor-divider overhead that reduces efficiency. The SOT-23-3 package occupies minimal PCB area, and the 1 uA maximum off-state cathode current (when REF pin is grounded) eliminates power dissipation concerns in shutdown modes.

Working Principle: TLVH431IDBZR Working Principle

The TLVH431 is a three-terminal shunt regulator consisting of an internal 1.24V bandgap reference, a transconductance error amplifier, and an open-collector NPN output transistor. When the voltage at the REF pin exceeds the internal 1.24V reference, the error amplifier drives the cathode (K) pin to sink more current, pulling the cathode voltage lower. Conversely, when REF falls below 1.24V, the cathode current decreases, allowing the cathode voltage to rise. In the typical application with two external resistors R1 and R2 from cathode to REF and REF to anode respectively, the output voltage is set by VO = VREF x (1 + R1/R2) + Iref x R1, where Iref is typically 0.1 uA. The device enters regulation when the cathode current exceeds the minimum 100 uA threshold. In isolated flyback converters, the TLVH431 is used with an optocoupler to close the feedback loop: the TLVH431 compares a fraction of the output voltage with its reference and drives the optocoupler LED, which modulates the primary-side PWM controller duty cycle.

Pin Description: TLVH431IDBZR Pin Definition and Functions
Pin Mnemonic Description
1 REF Reference input (1.24V threshold)
2 K Cathode (output, active pull-down)
3 A Anode (ground reference)
Application Scenarios: In which products and applications is TLVH431IDBZR used
  • Secondary side regulation in 3.3V flyback SMPS with optocoupler feedback, replacing TL431 for lower-voltage outputs
  • Adjustable voltage monitoring with 1.24V reference enabling detection of 1.8V and lower logic rails
  • Low-cost precision current sink with output voltage set by two external resistors from 1.24V to 18V
  • Zener diode replacement with sharp turn-on characteristic and 0.25 ohm dynamic impedance for improved regulation
Alternative Models: What chips are recommended as replacements for TLVH431IDBZR
Model Manufacturer Key Difference
TL431IDBZR TI 2.495V reference (higher min voltage), widely used
TLV431IDBZR TI 1.24V reference, lower max cathode voltage (6V)
TLVH432IDBZR TI Same as TLVH431 with alternative SOT-23 pinout
ZR431 Zetex/Diodes 1.24V reference, 1% grade available

Recommend Parts

MCP6S26-I

6-channel PGA, SPI interface, gains 1-32V/V, 10MHz BW, rail-to-rail, 2.5-5.5V, SOIC-14

Brand: MICROCHIP

Package: SOIC-14 (150 mils body width)

IN STOCK: 6800pcs

Cargo cycle: 3-7 Days

The minimum order is 1

W25Q80VSSI

8Mbit Serial Flash, Quad SPI, 104MHz, SOIC-8, 2.7-3.6V

Brand: Winbond

Package: SOIC-8 208mil (5.3×8.0mm)

IN STOCK: 4316pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MM3Z9V1

9.1V 200mW Zener diode, SOD-323, onsemi/Diotec

Brand: ON

Package: SOD-323 (2.5 x 1.25 x 0.85 mm)

IN STOCK: 10735pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AT89S51

8-bit 8051 MCU, 4KB ISP Flash, 128B RAM, 32 I/O, 2 timers, UART, watchdog timer, dual DPTR, 33MHz, ISP programming, PDIP-40, Atmel AT89S51.

Package: PDIP-40 / TQFP-44 / PLCC-44

IN STOCK: 15000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

GD32F303CBT6

Cortex-M4 32-bit MCU, 120MHz, 128KB Flash, 32KB SRAM, LQFP-48

Brand: gigadevice

Package: LQFP-48 (7x7mm, 0.5mm pitch)

IN STOCK: 3342pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MIC5205-3.3YM5-TR

3.3V 150mA ultra-low-noise LDO, 165mV dropout, 30uVrms noise, SOT-23-5

Brand: MICROCHIP

Package: SOT-23-5 (2.9 x 1.6 x 1.1mm)

IN STOCK: 9858pcs

Cargo cycle: 3-7 Days

The minimum order is 1