Opens in a new tab

DS2482S-100+T&R

1-Wire Master Bridge, I2C to 1-Wire, 1-CH, SOIC-8

5678

Effective Inventory

Image for reference only

Manufacturer Part:

DS2482S-100+T&R

Package:

SOIC-8 (4.9 x 3.9 x 1.5 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The DS2482S-100+T&R from Maxim Integrated (now Analog Devices) is a single-channel 1-Wire master I2C-to-1-Wire bridge with active pull-up and SOIC-8 package.

Key Specifications

Type I2C to 1-Wire Bridge (1 Channel)
1-Wire Channels 1
Host Interface I2C (up to 400kHz Fast Mode)
1-Wire Data Rate Standard (16.3kbps) and Overdrive (143kbps)
Active Pull-up Yes (slew-rate controlled)
1-Wire Pull-up Voltage 2.8V to 5.25V
Supply Voltage 2.8V to 5.25V
Operating Current 1.5 mA (typical, active)
Standby Current 850 uA (typical)
Package SOIC-8 (150 mil)
Operating Temperature -40C to +85C

Features

  • Single-channel I2C to 1-Wire protocol bridge
  • Active pull-up for reliable 1-Wire communication
  • Supports Standard and Overdrive 1-Wire speeds
  • I2C interface up to 400kHz
  • Programmable strong pull-up for EPROM programming
  • Internal timers for precise 1-Wire timing

Applications

  • iButton reader interfaces
  • 1-Wire sensor networks
  • Embedded 1-Wire master
  • Thermocouple and temperature sensor networks
Product Introduction: DS2482S-100+T&R Product Introduction

The DS2482S-100+T&R from Maxim Integrated (now part of Analog Devices) is a single-channel I2C-to-1-Wire bridge that enables any I2C-capable host to communicate with 1-Wire slave devices. The device handles all 1-Wire signaling and timing requirements, including active pull-up for reliable communication with multiple 1-Wire devices on the bus. The active pull-up feature provides a controlled slew-rate pull-up that minimizes ringing on the 1-Wire line while providing sufficient current for fast rise times. The DS2482-100 supports both Standard (16.3kbps) and Overdrive (143kbps) 1-Wire communication speeds. The I2C interface supports up to 400kHz Fast Mode, making it compatible with most microcontroller I2C peripherals. The programmable strong pull-up can supply up to 20mA continuously for EPROM programming or parasite-powered temperature sensors. The internal timers ensure precise 1-Wire timing regardless of host I2C speed, eliminating the need for bit-banging 1-Wire protocols from firmware.

Working Principle: DS2482S-100+T&R Working Principle

The DS2482S-100+T&R acts as a protocol translator between the I2C bus and the 1-Wire bus. When the host writes to the DS2482’s I2C slave address (0x18, 0x19, or 0x1A depending on pin configuration), the device interprets the command and performs the corresponding 1-Wire operation. The 1-Wire Read/Write command byte specifies whether a 1-Wire reset, 1-Wire write byte, or 1-Wire read byte operation should be performed. For a 1-Wire reset, the DS2482 pulls the 1-Wire line low for 480us (Standard speed) or 48us (Overdrive speed), then releases it and detects the presence pulse from slave devices. For a 1-Wire write operation, the DS2482 generates the appropriate time slots (pull low for 60-120us for write-0, or pull low briefly for write-1). The active pull-up circuit monitors the 1-Wire line voltage during the rising edge and applies a strong pull-up (low impedance to VPUP) when the voltage rises above a threshold, accelerating the RC charging of the 1-Wire bus capacitance. Once the voltage reaches VPUP, the active pull-up reverts to a passive pull-up resistor to avoid overshoot. This controlled approach eliminates the need for a low-value passive pull-up resistor that would waste power and still have slow rise times with large bus capacitance.

Pin Description: DS2482S-100+T&R Pin Definition and Functions
Pin Name Type Function
1 SCL Input I2C clock input
2 SDA I/O I2C data (open-drain)
3 AD0 Input I2C slave address bit 0
4 GND Power Ground
5 AD1 Input I2C slave address bit 1
6 IO I/O 1-Wire data line (open-drain)
7 VPUP Power Active pull-up supply (2.8V-5.25V)
8 VCC Power Supply voltage (2.8V-5.25V)
Application Scenarios: In which products and applications is DS2482S-100+T&R used
  • DS18B20 temperature sensor network with I2C host via DS2482-100 active pull-up for reliable multi-drop bus
  • iButton reader with Overdrive speed (143kbps) for fast DS1990A serial number reading
  • Embedded 1-Wire master on I2C-only MCU with strong pull-up for parasite-powered DS18B20 temperature conversion
Alternative Models: What chips are recommended as replacements for DS2482S-100+T&R
Manufacturer Part Number Package Notes
ADI/Maxim DS2482-800+ SOIC-16 8-channel version
ADI/Maxim DS2480B SOIC-8 Serial (UART) to 1-Wire bridge
TI DS2482S-100+ SOIC-8 Same device (TI distribution)
Silicon Labs CP2112 QFN-24 USB to I2C, no native 1-Wire

Recommend Parts

0751.0505

Schurter fuse, 0751.0505

Brand: schurter

Package: See datasheet

IN STOCK: 6768pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TL062CDR

Low-power JFET-input dual op-amp, 1MHz GBW, 30pA Ibias, SOIC-8, ±3.5V to ±18V

Brand: TI

Package: SOIC-8 (3.9 x 4.9 x 1.75mm)

IN STOCK: 11576pcs

Cargo cycle: 3-7 Days

The minimum order is 1

P89LPC922FN

8-bit 80C51 MCU, 8KB Flash, 256B RAM, 20-SSOP

Brand: NXP

Package: SSOP-20 (7.2 x 5.3 mm)

IN STOCK: 12628pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AC0603JR-070RL

Chip Resistor, 0Ω (Zero Ohm Jumper), ±5%, 0603 (1608 Metric), 1/10W (100mW)

Brand: Yageo

Package: 0603 (1608 Metric)

IN STOCK: 100000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LMR34206FSC5RNXRQ1

42V 2A sync buck, 5V fixed, 2.2MHz, 18uA Iq, AEC-Q100, SOT-563

Brand: TI

Package: SOT-563 (1.6 x 1.2 x 0.55mm)

IN STOCK: 6500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AO3402

30V N-channel trench MOSFET, SOT-23, 4A, RDS(on) 52m ohm max @ 10V, Qg 10nC, 2.5V gate drive capable, -55C to +150C.

Brand: aosmd

Package: SOT-23 (2.9 x 1.6 x 1.25mm)

IN STOCK: 14066pcs

Cargo cycle: 3-7 Days

The minimum order is 1