Opens in a new tab

LM358

Dual Op-Amp, 3V-32V Single Supply, 1.1MHz GBW, General Purpose

2203

Effective Inventory

Image for reference only

Manufacturer Part:

LM358

Package:

SOIC-8 / DIP-8 (multiple package options)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The LM358 is a classic dual operational amplifier from Texas Instruments, one of the most widely used op-amps in the electronics industry. Featuring two independent, high-gain, internally frequency-compensated amplifiers designed specifically for single-supply operation from 3V to 32V, the LM358’s input common-mode range extends down to ground, enabling direct interfacing with ground-referenced sensors. With unity-gain bandwidth of 1.1MHz and low quiescent current, this versatile device serves in active filters, comparators, buffers, and sensor amplifiers across virtually every market segment including industrial, automotive, consumer, and telecom.

Key Specifications

Parameter Value
Manufacturer Texas Instruments
Part Number LM358
Product Category Operational Amplifiers
Number of Channels 2 (Dual)
Supply Voltage Range 3V to 32V single supply
Input Offset Voltage 2 mV typical
Input Bias Current 45 nA typical
Gain Bandwidth Product 1.1 MHz typical
Slew Rate 0.5 V/µs typical
Open-Loop Gain 100 dB typical
Available Packages SOIC-8, DIP-8, TSSOP-8, SOT-23-8
Operating Temperature 0°C to +70°C

Features

  • Two independent operational amplifiers in single package
  • Wide single-supply voltage range: 3V to 32V (±1.5V to ±16V dual)
  • Input common-mode voltage includes ground (0V)
  • Internally frequency compensated for unity gain
  • Large DC voltage gain: 100 dB typical
  • Unity-gain bandwidth: 1.1 MHz typical
  • Low supply current: 0.5 mA per amplifier
  • Low input offset voltage: 2 mV typical
  • Output short-circuit protection
  • Available in multiple package options (DIP, SOIC, SOT-23)

Applications

  • Active filters and signal conditioning circuits
  • Voltage followers and buffer amplifiers
  • Comparators and level detectors with hysteresis
  • Transducer amplifiers and sensor interfaces
  • DC gain blocks and summing amplifiers
Product Introduction: LM358 Product Introduction

The LM358 is the industry-standard dual operational amplifier manufactured by Texas Instruments. First introduced by National Semiconductor and now part of the TI portfolio, the LM358 has become one of the most popular and widely used op-amps in the world, available from dozens of manufacturers as a second-source device.

What makes the LM358 so versatile is its design for single-supply operation. Unlike traditional op-amps that require dual positive and negative supplies, the LM358 operates from a single supply voltage as low as 3V and as high as 32V. Critically, the input common-mode voltage range extends down to 0V (ground), which means it can accept input signals that are referenced to ground without requiring negative supply rails or DC bias circuitry.

Each amplifier in the LM358 features a PNP input stage, a high-gain second stage with Miller compensation, and a Class AB push-pull output stage. The open-loop gain is typically 100dB, and the unity-gain bandwidth is 1.1MHz. The output can source up to 20mA and sink 10mA, sufficient for driving LEDs, relays (with external transistor), and most analog circuits.

The LM358 is available in a wide variety of packages, from through-hole DIP-8 for prototyping to surface-mount SOIC-8, TSSOP-8, and even ultra-compact SOT-23-8 for space-constrained designs. It is the workhorse general-purpose op-amp found in virtually every type of electronic equipment.

Working Principle: LM358 Working Principle

The LM358 is a BJT-based operational amplifier with three main internal stages per channel:

1. Input Differential Stage: Each amplifier uses a PNP (lateral PNP in some implementations) differential pair as the input stage. The PNP architecture is what allows the common-mode input voltage to go all the way down to the negative supply (ground). The differential pair drives an NPN current mirror that acts as an active load, converting the differential current to a single-ended voltage output with high gain.

2. Gain Stage (Second Stage): A common-emitter amplifier (NPN transistor) with an active current-mirror load provides the bulk of the voltage gain — typically 60-80dB. An integrated Miller compensation capacitor creates a dominant pole that rolls off the open-loop gain at -20dB/decade, ensuring stability even at unity gain with approximately 60° phase margin.

3. Output Stage: The output uses a Class AB push-pull configuration. An NPN transistor sources current when the output needs to go high, and a PNP transistor sinks current when the output needs to go low. A bias circuit sets the quiescent current through both transistors to minimize crossover distortion. The output voltage swing typically goes from near ground (50-200mV above GND depending on load) to within about 1.5V of the positive supply.

4. Bias Reference: A shared on-chip bias reference (often a VBE-based multiplier or simple current mirror) generates stable bias currents for the input and output stages of both amplifiers.

5. Short-Circuit Protection: Output current limiting resistors or active current limit circuits protect the output transistors from damage under short-circuit conditions.

Pin Description: LM358 Pin Definition and Functions
Pin Name Type Description
1 1OUT Output Output of Amplifier 1 (Channel A)
2 1IN- Input Inverting input of Amplifier 1
3 1IN+ Input Non-inverting input of Amplifier 1
4 GND/VEE Power Negative power supply / ground. Connect to 0V for single-supply operation.
5 2IN+ Input Non-inverting input of Amplifier 2
6 2IN- Input Inverting input of Amplifier 2
7 2OUT Output Output of Amplifier 2 (Channel B)
8 VCC/V+ Power Positive power supply (3V to 32V). Decouple to GND with 0.1µF ceramic capacitor.

Note: Pinout is identical for DIP-8, SOIC-8, and TSSOP-8 packages. SOT-23-8 packages may have different pin ordering — refer to specific datasheet.

Application Scenarios: In which products and applications is LM358 used
  • Sensor signal amplification and conditioning
  • Active low-pass, high-pass, and band-pass filters
  • Voltage followers and impedance buffers
  • Schmitt trigger comparators and level detectors
  • Current sense amplifiers and transimpedance amplifiers
Alternative Models: What chips are recommended as replacements for LM358
Manufacturer Part Number Package Notes
Texas Instruments LM258 SOIC-8 Essentially identical, different temp grading
Texas Instruments LM2904 SOIC-14 Quad version (4 amplifiers)
STMicroelectronics LM358DT SOIC-8 Pin-compatible direct alternative
ON Semiconductor LM358DR2G SOIC-8 Direct substitute
NXP LM358D SOIC-8 Alternative source
Microchip MCP6002 SOIC-8 1.8V CMOS, low-power alternative

Recommend Parts

MCP6S26-I

6-channel PGA, SPI interface, gains 1-32V/V, 10MHz BW, rail-to-rail, 2.5-5.5V, SOIC-14

Brand: MICROCHIP

Package: SOIC-14 (150 mils body width)

IN STOCK: 6800pcs

Cargo cycle: 3-7 Days

The minimum order is 1

W25Q80VSSI

8Mbit Serial Flash, Quad SPI, 104MHz, SOIC-8, 2.7-3.6V

Brand: Winbond

Package: SOIC-8 208mil (5.3×8.0mm)

IN STOCK: 4316pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MM3Z9V1

9.1V 200mW Zener diode, SOD-323, onsemi/Diotec

Brand: ON

Package: SOD-323 (2.5 x 1.25 x 0.85 mm)

IN STOCK: 10735pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AT89S51

8-bit 8051 MCU, 4KB ISP Flash, 128B RAM, 32 I/O, 2 timers, UART, watchdog timer, dual DPTR, 33MHz, ISP programming, PDIP-40, Atmel AT89S51.

Package: PDIP-40 / TQFP-44 / PLCC-44

IN STOCK: 15000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

GD32F303CBT6

Cortex-M4 32-bit MCU, 120MHz, 128KB Flash, 32KB SRAM, LQFP-48

Brand: gigadevice

Package: LQFP-48 (7x7mm, 0.5mm pitch)

IN STOCK: 3342pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MIC5205-3.3YM5-TR

3.3V 150mA ultra-low-noise LDO, 165mV dropout, 30uVrms noise, SOT-23-5

Brand: MICROCHIP

Package: SOT-23-5 (2.9 x 1.6 x 1.1mm)

IN STOCK: 9858pcs

Cargo cycle: 3-7 Days

The minimum order is 1