Opens in a new tab

LM5069MM-1

Positive High-Voltage Hot Swap Controller, 9V-80V, Power Limit, VSSOP-10

8934

Effective Inventory

Image for reference only

Manufacturer Part:

LM5069MM-1

Package:

VSSOP-10, 3.0 x 3.0 x 0.8 mm

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The LM5069MM-1 is a positive high-voltage hot swap controller from Texas Instruments, designed to allow safe insertion and removal of circuit boards from live backplanes operating at 9V to 80V. By controlling the gate of an external N-channel MOSFET, the LM5069 limits inrush current during board insertion and provides overcurrent protection during normal operation. The device features programmable power limiting that protects the MOSFET by constraining its power dissipation within safe limits. Version -1 features a latch-off fault response, making it suitable for systems requiring immediate shutoff on fault conditions in telecom, industrial, and high-voltage server applications.

Key Specifications

Parameter Value
Manufacturer Texas Instruments
Part Number LM5069MM-1
Product Category Hot Swap / Power Switch Controllers
Input Voltage Range 9V to 80V
Control Topology External N-MOSFET, current mode
Current Sensing External sense resistor (V_SNS = 50mV)
Power Limiting Programmable via TIMER pin resistor
Fault Response Latch-off (Version -1)
UVLO Threshold Adjustable via UVLO/EN pin
Gate Drive Charge-pump based, 13V above VIN
Package / Case VSSOP-10
Operating Temperature -40°C to +125°C

Features

  • Wide operating range: 9V to 80V (up to 100V transient)
  • Controls external N-channel MOSFET
  • Programmable current limit (50mV sense threshold)
  • Programmable power limit for MOSFET SOA protection
  • Inrush current control during board insertion
  • Version -1: Latch-off fault response
  • Adjustable undervoltage lockout (UVLO)
  • Power-good (PGD) output flag
  • Integrated charge-pump gate drive
  • Thermal shutdown protection

Applications

  • Hot swap / plug-in board protection
  • 48V telecom and server power systems
  • 24V industrial bus and PLC systems
  • Active OR-ing for redundant power supplies
  • Circuit breaker and eFuse applications
Product Introduction: LM5069MM-1 Product Introduction

The LM5069MM-1 is a high-voltage hot swap controller from Texas Instruments, designed to enable safe insertion and removal of printed circuit boards from live backplane systems. Operating from 9V to 80V, this device is well-suited for 24V industrial systems, 48V telecom infrastructure, and high-voltage server power architectures.

Hot swap controllers prevent damage to connectors, components, and the backplane by controlling the inrush current when a board is plugged into a live power bus. The LM5069 achieves this by slowly ramping the gate of an external N-channel MOSFET, allowing the output voltage and load current to rise in a controlled manner. This eliminates the large capacitive charging currents that would otherwise flow into the board’s bulk capacitors.

The LM5069 features both current limiting and power limiting for comprehensive MOSFET protection. The current limit is set by an external sense resistor (50mV threshold), while the power limit is programmed by a resistor on the TIMER pin. Power limiting ensures the MOSFET operates within its safe operating area (SOA) even during fault conditions.

Version -1 of the LM5069 features a latch-off fault response: when an overcurrent fault persists beyond the programmed fault time, the GATE pin is pulled low and the device latches off. The device remains off until power is recycled or the UVLO/EN pin is toggled. The VSSOP-10 package provides a compact solution for space-constrained designs.

Working Principle: LM5069MM-1 Working Principle

The LM5069 operates as a hot swap controller with the following functional blocks:

1. Undervoltage Lockout (UVLO): The UVLO/EN pin must rise above its 1.25V threshold for the device to start up. An external resistor divider from VIN to GND sets the UVLO threshold. Below this threshold, the GATE pin is held low and the MOSFET is off.

2. Power-Up and Inrush Control: When UVLO is satisfied, the charge pump begins powering the GATE pin through an internal current source. The GATE voltage rises, and as the MOSFET begins to conduct, the output voltage (V_OUT) ramps up. The inrush current is controlled by the rate of V_OUT rise and the value of the output capacitance. The TIMER capacitor sets the soft-start / power-up timeout.

3. Current Limiting: During normal operation, the device monitors the voltage across the external sense resistor (R_SNS) between VIN and SNS pins. If the load current exceeds the programmed limit (I_LIMIT = 50mV / R_SNS), the gate drive is reduced to regulate the current at the limit level. The fault timer starts charging.

4. Power Limiting: In addition to current limiting, the LM5069 measures the voltage across the MOSFET (V_IN – V_OUT) and the load current, then limits the power dissipation (P = V × I) of the external MOSFET. This ensures the MOSFET operates within its SOA boundaries, especially during start-up into heavy capacitive loads or fault conditions.

5. Fault Response (Latch-off, Version -1): If the overcurrent or power-limiting condition persists beyond the programmed fault timeout (set by TIMER capacitor), the GATE pin is pulled low, turning off the MOSFET. The device latches in the off state. To reset, either cycle VIN below UVLO or toggle the UVLO/EN pin.

6. Power Good Output: The PGD pin is an open-drain output that goes low when V_OUT rises above approximately 92% of VIN (the MOSFET is fully on), indicating that power is good.

Pin Description: LM5069MM-1 Pin Definition and Functions
Pin Name Type Description
1 UVLO/EN Input Undervoltage lockout / enable. Connect resistor divider from VIN to set turn-on threshold. Drive low to disable. 1.25V rising threshold.
2 TIMER I/O Fault timer / power limit setting. Connect capacitor to GND for fault timeout duration. Current out of pin sets power limit level.
3 PGD Output Power-good open-drain output. Pull low when V_OUT is below ~92% of VIN. Requires external pull-up resistor.
4 GND Ground Signal and power ground.
5 SNS Input Current sense input. Connect to load side of sense resistor (R_SNS). Current limit threshold is 50mV above VIN.
6 VIN Power Input Positive supply input (9V to 80V). Bypass with ceramic capacitor to GND.
7 VIN Power Input Second VIN pin. Connected internally to Pin 6. Both pins must be connected together.
8 GATE Output Gate drive output for external N-MOSFET. Connect to MOSFET gate. 13V above VIN typical.
9 GATE Output Second gate drive pin. Connected internally to Pin 8.
10 OUT Input Output voltage sense. Connect to output side of MOSFET. Used for power limit and power-good detection.
Application Scenarios: In which products and applications is LM5069MM-1 used
  • 48V telecom line card and server blade hot swap
  • 24V industrial PLC module plug-in protection
  • Redundant power supply OR-ing and load sharing
  • Electronic circuit breaker / eFuse for high-voltage buses
  • Battery management and load switching systems
Alternative Models: What chips are recommended as replacements for LM5069MM-1
Manufacturer Part Number Package Notes
TI LM5069MM-2 VSSOP-10 Auto-restart fault response version
TI LM25069 VSSOP-10 Lower voltage (2.9V-18V) version
TI LM5066 QFN-24 With PMBus telemetry
ADI LTC4231 MSOP-12 Hot swap with ideal diode
ADI LTC4259 SSOP-36 Quad 48V hot swap
Microchip MIC2593 MSOP-8 Single hot swap controller

Recommend Parts

ISO1176TDWR

Isolated RS-485 transceiver, 40Mbps, integrated transformer driver, SOIC-16

Brand: TI

Package: SOIC-16 (DW, wide-body, 10.3 x 10.3 mm)

IN STOCK: 6874pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFB4020PBF

200V N-Channel HEXFET Power MOSFET, 31A, 68 mΩ RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 14149pcs

Cargo cycle: 3-7 Days

The minimum order is 1

NRF52832-QFAA-T

Nordic BLE SoC, ARM Cortex-M4 @ 64MHz, 64KB Flash, 32KB RAM, QFN-48

Package: See datasheet

IN STOCK: 10958pcs

Cargo cycle: 3-7 Days

The minimum order is 1

UCC28740DR

CVCC Flyback Controller, 700V startup, opto feedback, <10mW no-load, SOIC-7

Brand: TI

Package: SOIC-7 (4.9 x 3.9 x 1.75 mm)

IN STOCK: 4840pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MMUN2211LT1G

NPN digital transistor, R1=10kΩ R2=10kΩ, 50V, 100mA, SOT-23-3, pre-biased BRT switch

Brand: Onsemi

Package: SOT-23-3 (TO-236, SC-59)

IN STOCK: 8500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

PIC32MX795F512L-80I/PF

32-bit PIC32MX MCU with Ethernet/CAN/USB, 80MHz, 512KB Flash, TQFP-100, industrial

Brand: MICROCHIP

Package: TQFP-100 (14 x 14 mm)

IN STOCK: 7912pcs

Cargo cycle: 3-7 Days

The minimum order is 1