Opens in a new tab

Home » Integrated Circuits ICs » LMV358IDR

LMV358IDR

Dual rail-to-rail op-amp, 1MHz, 2.7-5.5V, SOIC-8

40000

Effective Inventory

Image for reference only

Manufacturer Part:

LMV358IDR

Package:

SOIC-8 (4.9 x 3.9 x 1.58 mm)

Brand:

Product Categories:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The LMV358IDR from Texas Instruments is a dual general-purpose rail-to-rail output op-amp with 1MHz GBW, 2.7V-5.5V supply, and 210uA supply current in SOIC-8 package.

Key Specifications

Channels 2 (dual)
Supply Voltage 2.7 V to 5.5 V (single or dual supply)
Gain-Bandwidth Product 1 MHz
Slew Rate 0.8 V/us
Input Offset Voltage 1.7 mV typical / 7 mV max
Input Bias Current 12 nA typical
Input Common-Mode Range Ground to VDD – 1.2V
Output Swing Rail-to-rail (within 30mV of rails)
Supply Current (per amplifier) 105 uA typical
Output Drive Current 60 mA short circuit
CMRR 75 dB typical
Package SOIC-8 (IDR suffix)
Operating Temperature -40 to +85 C

Features

  • Rail-to-rail output swings within 30mV of supply rails
  • 2.7V minimum supply for low-voltage operation
  • 1MHz GBW for moderate-speed signal processing
  • 210uA total supply current for both amplifiers
  • Input common-mode range includes ground

Applications

  • Portable and battery-powered signal conditioning
  • Low-voltage active filter design
  • Sensor amplifier and transducer interface
  • Audio preamplifier and buffer
  • General-purpose low-voltage analog circuits
Product Introduction: LMV358IDR Product Introduction

The LMV358IDR from Texas Instruments is a dual general-purpose rail-to-rail output operational amplifier in SOIC-8 package. The device operates from 2.7V to 5.5V supply with 1MHz gain-bandwidth product, 0.8V/us slew rate, and 210uA total supply current for both amplifiers. The rail-to-rail output swings within 30mV of the supply rails, maximizing dynamic range in low-voltage applications. The input common-mode range extends from ground to VDD-1.2V, allowing single-supply operation with ground-referenced signals. The IDR suffix denotes SOIC-8 package with tape and reel.

Working Principle: LMV358IDR Working Principle

The LMV358IDR operates as a dual rail-to-rail output operational amplifier. (1) The input stage uses a PNP differential pair that allows the input common-mode range to extend to ground (0V), critical for single-supply applications where the input signal may be at or near ground. The upper limit of the common-mode range is VDD – 1.2V, set by the bias circuit. The 1.7mV typical input offset voltage is adequate for most general-purpose applications. (2) The output stage uses a common-emitter (Class AB) configuration that allows the output to swing within 30mV of both supply rails under light load. This is significantly better than standard LM358 op-amps that can only swing to within 1.5V of VDD. The rail-to-rail output maximizes the usable signal range in low-voltage (3.3V/5V) systems where every millivolt of dynamic range matters. (3) The 1MHz gain-bandwidth product and 0.8V/us slew rate determine the maximum frequency and amplitude the amplifier can handle without distortion. For a unity-gain buffer, the -3dB bandwidth is 1MHz. For a gain-of-10 amplifier, the bandwidth is 100kHz. The maximum undistorted sine wave amplitude at frequency f is: VOUT(max) = SR / (2 x pi x f), where SR is the slew rate. At 100kHz, the maximum undistorted output amplitude is approximately 1.27V peak.

Pin Description: LMV358IDR Pin Definition and Functions
Pin Name Function
1 1OUT Amplifier 1 output
2 1IN- Amplifier 1 inverting input
3 1IN+ Amplifier 1 non-inverting input
4 GND Negative supply / ground
5 2IN+ Amplifier 2 non-inverting input
6 2IN- Amplifier 2 inverting input
7 2OUT Amplifier 2 output
8 V+ Positive supply (2.7-5.5V)
Application Scenarios: In which products and applications is LMV358IDR used
  • Portable and battery-powered signal conditioning with rail-to-rail output
  • Low-voltage active filter design at 1MHz GBW
  • Sensor amplifier and transducer interface with ground-referenced input
  • Audio preamplifier and buffer in 3.3V/5V systems
  • General-purpose low-voltage analog circuits with 210uA IQ
Alternative Models: What chips are recommended as replacements for LMV358IDR
Model Manufacturer Key Difference
LMV358MFX TI Same, Micro8 package
MCP6002-I/SN Microchip 1MHz, R-R, SOIC-8
TLV2462CDR TI 6.4MHz, R-R I/O, low power
OPA2314AIDR TI 3MHz, R-R I/O, precision
NJMU358M NJR 1MHz, R-R output, DIP-8

Recommend Parts

MSP432P401RIPZR

Ultra-low-power Cortex-M4F MCU, 48MHz, 256KB Flash, 14-bit ADC, 850nA standby, 100-LQFP

Brand: TI

Package: 100-LQFP (14 x 14 x 1.4mm)

IN STOCK: 3750pcs

Cargo cycle: 3-7 Days

The minimum order is 1

PTN78060WAH

4.5A positive-input buck-IT module, adjustable, SMD module

Brand: TI

Package: Module (34.3 x 19.3 x 8.2 mm)

IN STOCK: 4786pcs

Cargo cycle: 3-7 Days

The minimum order is 1

PIC16F1526-I/PT

8-bit PIC16 MCU, 14KB Flash, 768B RAM, 30-ch 10-bit ADC, 10x CCP, 64-TQFP, XLP

Brand: MICROCHIP

Package: TQFP-64 (10.0 x 10.0 x 1.05 mm)

IN STOCK: 5600pcs

Cargo cycle: 3-7 Days

The minimum order is 1

R2A20178NP

8-channel 8-bit voltage output DAC, R-2R architecture, buffered rail-to-rail output, SPI interface up to 25MHz, 2.7-5.5V

Brand: Renesas

Package: 24-pin HWQFN (4x4x0.75mm)

IN STOCK: 6399pcs

Cargo cycle: 3-7 Days

The minimum order is 1

VS-40CPQ100-N3

Dual Schottky rectifier, common cathode, 2x20A, 100V, 0.61V VF, TO-247AC-3L, Vishay Q-series, 175 degC TJ, guard ring

Brand: VISHAY

Package: TO-247AC 3L (3-lead through-hole, 15.5mm width, tab for heatsink, common cathode configuration)

IN STOCK: 8950pcs

Cargo cycle: 3-7 Days

The minimum order is 1

BSC040N10NS5

OptiMOS 5 N-ch 100V 4mΩ 136A MOSFET, SuperSO8

Brand: infineon

Package: PG-TDSON-8 (SuperSO8, 5 x 6mm)

IN STOCK: 10509pcs

Cargo cycle: 3-7 Days

The minimum order is 1