Opens in a new tab

LMV722MX

Dual op-amp, 10MHz GBW, 9nV/√Hz, RRIO, 930µA/ch, 2.2-5.5V, SOIC-8

9400

Effective Inventory

Image for reference only

Manufacturer Part:

LMV722MX

Package:

SOIC-8

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The LMV722MX from Texas Instruments is a dual low-noise, low-voltage, low-power operational amplifier with 10 MHz gain-bandwidth product, 5.25 V/µs slew rate, and 930 µA supply current per amplifier. Operating from 2.2V to 5.5V with rail-to-rail output and input common-mode range including ground, it is housed in an SOIC-8 package.

Key Specifications

  • Channels: 2 (dual)
  • Supply Voltage: 2.2V ~ 5.5V
  • Gain-Bandwidth Product: 10 MHz
  • Slew Rate: 5.25 V/µs
  • Supply Current: 930 µA/amplifier typical (2.2V)
  • Input Offset Voltage: 3 mV max (25°C), 3.5 mV max (over temperature)
  • Input Bias Current: 260 nA typical
  • CMRR: 89 dB typical
  • PSRR: 90 dB typical
  • Voltage Noise: 9 nV/√Hz at 1 kHz
  • Current Noise: 0.3 pA/√Hz at 1 kHz
  • THD: 0.004% (1 kHz, AV=1)
  • Output Swing: 50 mV from rails (2kΩ load)
  • Phase Margin: 67°
  • Operating Temperature: -40°C ~ 105°C
  • Package: SOIC-8

Features

  • 10 MHz GBW with only 930 µA supply current
  • Low input voltage noise: 9 nV/√Hz
  • Rail-to-rail output swing
  • Input common-mode range includes ground
  • Wide supply range: 2.2V to 5.5V
  • Good capacitive load driving capability

Applications

  • Cellular and cordless phones
  • Active filters and buffers
  • Laptops and PDAs
  • Battery-powered electronics
  • Audio signal conditioning
Product Introduction: LMV722MX Product Introduction

The LMV722MX from Texas Instruments is a dual operational amplifier optimized for low-voltage, low-noise applications. It combines a 10 MHz gain-bandwidth product with low 9 nV/√Hz voltage noise density, making it suitable for audio and sensor signal conditioning where both bandwidth and noise performance are critical. The 930 µA per-channel supply current is modest for a 10 MHz amplifier, providing a favorable GBW-to-power ratio. The bipolar input stage delivers low noise and high CMRR (89 dB typical), while the rail-to-rail output stage maximizes dynamic range in single-supply applications. The input common-mode range includes ground, enabling direct sensing of ground-referenced signals. The MX suffix indicates SOIC-8 packaging.

Working Principle: LMV722MX Working Principle

The LMV722MX uses a BiCMOS process that combines a bipolar input stage with CMOS output stage circuitry. The bipolar input differential pair provides low voltage noise (9 nV/√Hz) and high transconductance, enabling the 10 MHz gain-bandwidth product with moderate supply current. The input common-mode range extends 0.3V below the negative rail through a complementary PNP/NPN input pair arrangement. The CMOS rail-to-rail output stage uses complementary PMOS/NMOS transistors in a common-source configuration, allowing the output to swing within 50 mV of each supply rail under 2kΩ load. Internal compensation ensures stability with unity-gain feedback. The bipolar input stage contributes a 260 nA typical bias current, which is higher than CMOS-input alternatives but provides superior noise performance.

Pin Description: LMV722MX Pin Definition and Functions
Pin Name Function
1 OUT A Amplifier A output
2 -IN A Amplifier A inverting input
3 +IN A Amplifier A non-inverting input
4 GND Negative supply / Ground
5 +IN B Amplifier B non-inverting input
6 -IN B Amplifier B inverting input
7 OUT B Amplifier B output
8 V+ Positive supply (2.2-5.5V)
Application Scenarios: In which products and applications is LMV722MX used

The LMV722MX excels in audio signal paths where the 9 nV/√Hz noise density preserves signal integrity from low-level microphone or line-level sources. In cellular phones, the 10 MHz bandwidth supports anti-aliasing filters for voice-band and audio CODEC interfaces. For active filter applications, the GBW product supports filter topologies up to several hundred kHz with reasonable Q factors. In laptop audio subsystems, the rail-to-rail output and ground-including input simplify single-supply designs. The 0.004% THD at 1 kHz makes it transparent in audio signal chains.

Alternative Models: What chips are recommended as replacements for LMV722MX
Model Manufacturer Key Difference
LMV722MM/NOPB Texas Instruments VSSOP-8 package, same specs
NE5532DR Texas Instruments Dual, 10MHz, 5nV/√Hz, ±22V
OPA2340EA Texas Instruments 5.5MHz, CMOS input, 0.5pA Ibias

Recommend Parts

MCP6S26-I

6-channel PGA, SPI interface, gains 1-32V/V, 10MHz BW, rail-to-rail, 2.5-5.5V, SOIC-14

Brand: MICROCHIP

Package: SOIC-14 (150 mils body width)

IN STOCK: 6800pcs

Cargo cycle: 3-7 Days

The minimum order is 1

W25Q80VSSI

8Mbit Serial Flash, Quad SPI, 104MHz, SOIC-8, 2.7-3.6V

Brand: Winbond

Package: SOIC-8 208mil (5.3×8.0mm)

IN STOCK: 4316pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MM3Z9V1

9.1V 200mW Zener diode, SOD-323, onsemi/Diotec

Brand: ON

Package: SOD-323 (2.5 x 1.25 x 0.85 mm)

IN STOCK: 10735pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AT89S51

8-bit 8051 MCU, 4KB ISP Flash, 128B RAM, 32 I/O, 2 timers, UART, watchdog timer, dual DPTR, 33MHz, ISP programming, PDIP-40, Atmel AT89S51.

Package: PDIP-40 / TQFP-44 / PLCC-44

IN STOCK: 15000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

GD32F303CBT6

Cortex-M4 32-bit MCU, 120MHz, 128KB Flash, 32KB SRAM, LQFP-48

Brand: gigadevice

Package: LQFP-48 (7x7mm, 0.5mm pitch)

IN STOCK: 3342pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MIC5205-3.3YM5-TR

3.3V 150mA ultra-low-noise LDO, 165mV dropout, 30uVrms noise, SOT-23-5

Brand: MICROCHIP

Package: SOT-23-5 (2.9 x 1.6 x 1.1mm)

IN STOCK: 9858pcs

Cargo cycle: 3-7 Days

The minimum order is 1