Opens in a new tab

LT3094EDD

Ultra Low Noise Negative LDO, 500mA, -1.2V to -42V, DFN-12

11965

Effective Inventory

Image for reference only

Manufacturer Part:

LT3094EDD

Package:

12-Lead DFN (3 x 4 x 0.75 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The LT3094EDD is an ultra-low noise, ultra-high PSRR negative linear regulator from Analog Devices, designed to complement the positive LT3045 in dual-supply systems requiring exceptionally clean negative voltage rails. Delivering up to 500mA of output current with 0.8µV RMS output noise and 74dB PSRR at 1MHz, this device provides the same industry-leading noise performance as its positive counterpart but for negative supply voltages. Operating from -1.8V to -45V input with adjustable output from 0V down to -42V using a single external resistor, the LT3094 is ideal for powering negative supply rails of high-performance op-amps, ADCs, DACs, and RF circuits in communications, medical, and instrumentation systems.

Key Specifications

Parameter Value
Manufacturer Analog Devices
Part Number LT3094EDD
Product Category Ultra-Low Noise Negative LDOs
Output Type Negative, adjustable (single resistor)
Input Voltage Range -1.8V to -45V
Output Voltage Range 0V to -42V (adjustable)
Output Current 500mA
Output Noise 0.8µV RMS (10Hz to 100kHz)
PSRR 74dB at 1MHz
Dropout Voltage 260mV typical @ 500mA
Package / Case 12-Lead DFN (3×4mm)
Operating Temperature -40°C to +125°C

Features

  • Ultra-low output noise: 0.8µV RMS (10Hz to 100kHz)
  • Ultra-high PSRR: 74dB at 1MHz
  • 500mA output current capability
  • Wide negative input: -1.8V to -45V
  • Adjustable negative output: 0V to -42V, single resistor
  • Low dropout: 260mV typical at 500mA
  • Low quiescent current: 2.5mA operating, 0.5mA shutdown
  • Programmable current limit
  • Precision enable threshold
  • Ceramic output capacitor stable
  • Reverse battery and reverse current protection
  • Thermal overload and short-circuit protection

Applications

  • Negative supply for high-speed data converters
  • Negative rails for precision op-amps
  • RF power amplifiers and microwave circuits
  • Medical imaging and diagnostic equipment
  • Test and measurement instruments
  • Post-regulation of negative switching supplies
Product Introduction: LT3094EDD Product Introduction

The LT3094EDD is an ultra-low noise, ultra-high PSRR negative linear regulator from Analog Devices, designed to provide clean negative supply rails for the most demanding precision analog and RF applications. As the negative counterpart to the award-winning LT3045 positive LDO, the LT3094 delivers the same exceptional performance but for negative voltage supplies, enabling complete low-noise dual-supply solutions.

The LT3094 achieves remarkable noise performance of just 0.8µV RMS (10Hz to 100kHz) and PSRR of 74dB at 1MHz — nearly unheard of for negative regulators. This level of performance is critical for high-performance analog systems that require clean negative supplies, such as high-speed data converters, precision instrumentation amplifiers, and low-noise RF circuits.

Using the same current-reference architecture as the LT3045, the LT3094 sets its output voltage with a single resistor connected from the SET pin to ground. A precision 50µA current source flows through this resistor, establishing VOUT = -50µA × R_SET. This approach eliminates the noise contribution of a traditional resistive feedback divider.

The device operates from -1.8V to -45V input and can provide outputs from 0V down to -42V (limited by the input-output differential). It is stable with ceramic output capacitors and includes comprehensive protection features including reverse battery protection, reverse current protection, programmable current limit, thermal shutdown, and short-circuit protection.

Working Principle: LT3094EDD Working Principle

The LT3094 is a negative LDO that mirrors the architecture of the positive LT3045 but with P-type and N-type devices swapped:

1. Negative Current-Reference Architecture: The LT3094 uses a precision -50µA current source that sinks current from the SET pin. When a resistor R_SET is connected from SET to ground (the more positive rail), the output voltage is VOUT = -50µA × R_SET. This architecture eliminates the noise that would be introduced by a traditional resistive divider.

2. Low-Noise Bandgap Reference: An advanced bandgap reference operates from the negative supply and generates the reference current with extremely low noise. Chopper stabilization and internal noise filtering achieve nanovolt-level noise spectral density.

3. High-PSRR Error Amplifier: The error amplifier is specially designed to maintain high power supply rejection at high frequencies. Multiple gain stages with optimized power supply rejection at each stage contribute to the 74dB PSRR at 1MHz, far exceeding traditional negative regulators.

4. NPN Pass Element: An NPN (or NMOS) pass transistor serves as the series regulation element between the negative input and negative output. The N-type device allows low dropout voltage (260mV typical at 500mA) and good high-frequency response.

5. Noise Reduction (NR) Pin: An external capacitor connected to the NR pin further filters the reference, reducing output noise to ultra-low levels. The NR capacitor value determines the noise floor and also affects start-up time.

6. Protection Features: The LT3094 includes reverse battery protection (prevents damage if the input supply is reversed), reverse current protection (prevents current from flowing from ground to output when the input is shorted), programmable current limit via a resistor, and thermal shutdown.

7. Stability: The device is stable with low-ESR ceramic output capacitors. The internal compensation is designed to work with a range of output capacitor values, ensuring robust stability across operating conditions.

Pin Description: LT3094EDD Pin Definition and Functions
Pin Name Type Description
1 IN Power Input Negative input voltage supply (-1.8V to -45V). Bypass with low-ESR ceramic capacitor to GND, placed close to pin.
2 EN/UVLO Input Enable / undervoltage lockout. Pull below -1.22V (more negative) to enable. Drive above -0.4V to shut down.
3 ILIM Input Current limit programming. Resistor to GND (positive rail) sets current limit level.
4 SET Input Voltage set pin. Connect resistor from SET to GND to set negative output voltage: VOUT = -50µA × R_SET.
5 NR Input Noise reduction pin. Connect capacitor from NR to GND to filter reference noise. 10nF typical for ultra-low noise.
6 GND Ground Ground (positive rail) connection. The system ground / most positive supply rail.
7 GND Ground Additional ground pin for thermal and low-impedance return.
8 GND Ground Third ground pin for high-current return path.
9 OUT Output Negative regulated output. Connect output capacitor (typically 10µF ceramic) and load here. More negative than GND.
10 OUT Output Second negative output pin. Connected internally to Pin 9.
11 OUTS Output Sense Output sense pin. Kelvin-sense connection for feedback. Connect directly to output capacitor at load side.
12 OUT Output Third negative output pin. Connected internally for low-resistance current path.
Application Scenarios: In which products and applications is LT3094EDD used
  • Negative supply rails for high-speed ADCs and DACs
  • Precision op-amp negative supply for instrumentation amplifiers
  • RF power amplifier biasing and negative supply regulation
  • Medical imaging equipment requiring clean dual supplies
  • Audio equipment with negative rail requirements
  • Post-regulation of negative buck-boost or inverting converters
Alternative Models: What chips are recommended as replacements for LT3094EDD
Manufacturer Part Number Package Notes
Analog Devices LT3094EMSE MSOP-12 Same device in MSOP-12 package
Analog Devices LT3045EDD DFN-10 Positive output complement
Analog Devices LT1964 TSOT-23 200mA negative LDO, lower noise spec
Texas Instruments TPS7A3301 QFN-20 1A negative ultra-low-noise LDO
Maxim MAX1735 SOT-23 120mA negative LDO alternative
Microchip TC2117 SOT-223 Low-cost negative 500mA LDO

Recommend Parts

ISO1176TDWR

Isolated RS-485 transceiver, 40Mbps, integrated transformer driver, SOIC-16

Brand: TI

Package: SOIC-16 (DW, wide-body, 10.3 x 10.3 mm)

IN STOCK: 6874pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFB4020PBF

200V N-Channel HEXFET Power MOSFET, 31A, 68 mΩ RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 14149pcs

Cargo cycle: 3-7 Days

The minimum order is 1

NRF52832-QFAA-T

Nordic BLE SoC, ARM Cortex-M4 @ 64MHz, 64KB Flash, 32KB RAM, QFN-48

Package: See datasheet

IN STOCK: 10958pcs

Cargo cycle: 3-7 Days

The minimum order is 1

UCC28740DR

CVCC Flyback Controller, 700V startup, opto feedback, <10mW no-load, SOIC-7

Brand: TI

Package: SOIC-7 (4.9 x 3.9 x 1.75 mm)

IN STOCK: 4840pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MMUN2211LT1G

NPN digital transistor, R1=10kΩ R2=10kΩ, 50V, 100mA, SOT-23-3, pre-biased BRT switch

Brand: Onsemi

Package: SOT-23-3 (TO-236, SC-59)

IN STOCK: 8500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

PIC32MX795F512L-80I/PF

32-bit PIC32MX MCU with Ethernet/CAN/USB, 80MHz, 512KB Flash, TQFP-100, industrial

Brand: MICROCHIP

Package: TQFP-100 (14 x 14 mm)

IN STOCK: 7912pcs

Cargo cycle: 3-7 Days

The minimum order is 1