Opens in a new tab

NCP1117ST33T3G

1A LDO, 3.3V fixed, 1.07V dropout @ 800mA, SOT-223, +/-1% accuracy

11500

Effective Inventory

Image for reference only

Manufacturer Part:

NCP1117ST33T3G

Package:

SOT-223-3 (6.70 x 3.70 x 1.69 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The NCP1117ST33T3G from onsemi is a low-dropout (LDO) positive linear voltage regulator providing a fixed 3.3 V output at up to 1 A in a SOT-223 package. It features a maximum dropout voltage of 1.2 V at 800 mA, output voltage accuracy of +/-1.0%, and internal current limiting and thermal shutdown protection.

Key Specifications

Output Voltage 3.3 V (fixed)
Output Current 1 A
Dropout Voltage 1.07 V typical @ 800 mA
Input Voltage Range Up to 20 V
Output Accuracy +/-1.0%
Quiescent Current 10 mA typical
Line Regulation 0.8 mV typical
Load Regulation 4.3 mV typical
Operating Temperature 0°C to +125°C

Features

  • Output current in excess of 1.0 A
  • Low dropout voltage: 1.2 V max at 800 mA over temperature
  • On-chip trimming for +/-1.0% output voltage accuracy
  • No minimum load requirement for regulation
  • Internal current limiting and safe operating area compensation
  • Thermal shutdown protection
  • Available in SOT-223 and DPAK packages
  • Pb-free device, RoHS compliant

Applications

  • Switching power supply post-regulation
  • Battery chargers and consumer electronics
  • Active SCSI terminators
  • Hard disk drive controller power
Product Introduction: NCP1117ST33T3G Product Introduction

The NCP1117ST33T3G from onsemi is a low-dropout positive linear voltage regulator capable of providing output current in excess of 1.0 A with a fixed 3.3 V output. The device features a maximum dropout voltage of 1.2 V at 800 mA over the full operating temperature range, making it suitable for applications where the input-to-output differential is limited. On-chip trimming adjusts the output voltage to within +/-1.0% accuracy, significantly tighter than industry-standard 1117 regulators. Internal protection features include output current limiting, safe operating area compensation, and thermal shutdown, ensuring reliable operation under fault conditions. The NCP1117 series can operate with input voltages up to 20 V and does not require a minimum load to maintain regulation. The SOT-223 package provides excellent thermal performance with a junction-to-case thermal resistance that supports full 1 A output when properly heat-sinked on the PCB copper area.

Working Principle: NCP1117ST33T3G Working Principle

The NCP1117ST33T3G operates as a series-pass linear regulator with three main functional blocks: (1) The bandgap reference generates a precise internal voltage of approximately 1.25 V, trimmed during manufacturing to achieve the +/-1.0% output accuracy. For the fixed 3.3 V version, internal resistor dividers scale the reference to produce the regulated output. (2) The error amplifier compares a fraction of the output voltage (sensed through the internal divider) with the bandgap reference. The amplifier output drives the base of the series-pass transistor, adjusting the conductance to maintain the output at the target 3.3 V. The pass transistor operates in the linear region, dissipating excess voltage as heat. (3) The protection circuitry includes current limiting that restricts the pass transistor current to a safe level during overload, safe operating area (SOA) compensation that reduces the current limit at high input-output differentials, and thermal shutdown that disables the output when the junction temperature exceeds approximately 175°C.

Pin Description: NCP1117ST33T3G Pin Definition and Functions
Pin No. Pin Name Function
1 GND/ADJ Ground (fixed version) / Adjust (adjustable version)
2 VOUT 3.3 V regulated output
3 VIN Unregulated input voltage (up to 20 V)
4 Tab Heat sink tab (connected to VOUT internally)
Application Scenarios: In which products and applications is NCP1117ST33T3G used
  • Post-regulation of switching power supply outputs where the +/-1.0% accuracy provides tighter voltage regulation than the switcher alone
  • Consumer electronics 3.3 V power rails converting from 5 V or higher supplies with adequate heatsinking for 1 A loads
  • Hard disk drive controller power supply where the 1 A current capability meets the startup surge requirements
  • Battery charger circuits using the 3.3 V fixed output as a reference or bias supply with thermal shutdown protecting against overtemperature
Alternative Models: What chips are recommended as replacements for NCP1117ST33T3G
Model Brand Vout Iout Package
AMS1117-3.3 Advanced Monolithic 3.3 V 1 A SOT-223
LD1117S33CTR ST 3.3 V 800 mA SOT-223
TLV1117LV33DCYR TI 3.3 V 1 A SOT-223
NCP1117IST33T3G onsemi 3.3 V 1 A SOT-223
IRU1117-33CD Infineon 3.3 V 800 mA SOT-223

Recommend Parts

ISO1176TDWR

Isolated RS-485 transceiver, 40Mbps, integrated transformer driver, SOIC-16

Brand: TI

Package: SOIC-16 (DW, wide-body, 10.3 x 10.3 mm)

IN STOCK: 6874pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFB4020PBF

200V N-Channel HEXFET Power MOSFET, 31A, 68 mΩ RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 14149pcs

Cargo cycle: 3-7 Days

The minimum order is 1

NRF52832-QFAA-T

Nordic BLE SoC, ARM Cortex-M4 @ 64MHz, 64KB Flash, 32KB RAM, QFN-48

Package: See datasheet

IN STOCK: 10958pcs

Cargo cycle: 3-7 Days

The minimum order is 1

UCC28740DR

CVCC Flyback Controller, 700V startup, opto feedback, <10mW no-load, SOIC-7

Brand: TI

Package: SOIC-7 (4.9 x 3.9 x 1.75 mm)

IN STOCK: 4840pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MMUN2211LT1G

NPN digital transistor, R1=10kΩ R2=10kΩ, 50V, 100mA, SOT-23-3, pre-biased BRT switch

Brand: Onsemi

Package: SOT-23-3 (TO-236, SC-59)

IN STOCK: 8500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TMS320F2810PBKA

C2000 Delfino DSP controller, 150MHz, 128KB Flash, BGA-179

Brand: TI

Package: BGA-179 (16 x 16 mm, PBK package)

IN STOCK: 3124pcs

Cargo cycle: 3-7 Days

The minimum order is 1