Opens in a new tab

NRF24L01P

2.4GHz Transceiver, 250kbps-2Mbps, SPI, Enhanced ShockBurst, QFN-20

12345

Effective Inventory

Image for reference only

Manufacturer Part:

NRF24L01P

Package:

QFN-20 (4.0 x 4.0 x 0.85 mm, 0.5mm pitch)

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The NRF24L01P from Nordic Semiconductor is a single-chip 2.4 GHz transceiver with 250kbps to 2Mbps data rates, SPI interface, and 1.9V to 3.6V supply in a QFN-20 package.

Key Specifications

Type 2.4 GHz RF Transceiver (ISM Band)
Frequency Range 2.400 GHz to 2.525 GHz (125 channels)
Data Rate 250 kbps / 1 Mbps / 2 Mbps
Output Power 0 dBm (max, programmable 0/-6/-12/-18 dBm)
Sensitivity -94 dBm @ 250kbps; -82 dBm @ 2Mbps
Range Up to 100m (open air, 0dBm, 250kbps)
Interface SPI (up to 8 MHz)
Supply Voltage 1.9 V to 3.6 V
TX Current 11.3 mA @ 0dBm
RX Current 13.5 mA @ 2Mbps
Standby Current 26 uA
Package QFN-20 (4 x 4 mm)
Operating Temperature -40C to +85C

Features

  • 2.4 GHz ISM band operation (global license-free)
  • Multi-data rate: 250kbps, 1Mbps, 2Mbps
  • Enhanced ShockBurst (ESB) protocol engine
  • Auto-acknowledgment and auto-retransmission
  • 1:6 star network topology (1 PTX to 6 PRX)
  • 3 individual 32-byte TX FIFOs and 3 RX FIFOs
  • Address and CRC computation in hardware
  • Low 26 uA standby current

Applications

  • Wireless sensor networks
  • Remote control and gaming peripherals
  • Home and building automation
  • IoT device connectivity
Product Introduction: NRF24L01P Product Introduction

The NRF24L01P from Nordic Semiconductor is a single-chip 2.4 GHz transceiver designed for ultra-low-power wireless applications. The device integrates a complete RF transceiver with frequency synthesizer, baseband protocol engine (Enhanced ShockBurst), and SPI host interface. The Enhanced ShockBurst engine handles packet assembly (preamble, address, CRC), auto-acknowledgment, and auto-retransmission, significantly reducing MCU firmware complexity. The three data rates (250kbps for maximum range, 1Mbps standard, 2Mbps for throughput) allow designers to trade range for speed. The 1:6 star network capability enables a primary transmitter (PTX) to communicate with up to 6 primary receivers (PRX) using unique addresses per pipe. The device is extremely popular in the Arduino/maker community and is widely used in commercial wireless products.

Working Principle: NRF24L01P Working Principle

The NRF24L01P uses a GFSK (Gaussian Frequency Shift Keying) modulation scheme in the 2.4 GHz ISM band. The frequency synthesizer generates the carrier frequency from a 16 MHz crystal reference, with channel spacing of 1 MHz (125 channels available). In TX mode, the baseband engine assembles the packet: 1-byte preamble + 3-5 byte address + 9-bit packet control + 0-32 byte payload + 1-2 byte CRC. The GFSK modulator shifts the carrier frequency by +/-160 kHz (at 250kbps), +/- 320 kHz (1Mbps), or +/- 640 kHz (2Mbps) to encode the data. In RX mode, the received signal is amplified by the LNA, down-converted, demodulated, and passed to the baseband engine which checks the address and CRC. The Enhanced ShockBurst engine automatically sends an acknowledgment (ACK) packet back to the transmitter upon successful reception. If no ACK is received, the transmitter retransmits up to a configurable count (auto-retransmit). The SPI interface provides read/write access to all configuration registers and FIFO data. The CE (Chip Enable) pin controls TX/RX mode entry.

Pin Description: NRF24L01P Pin Definition and Functions
Pin Name Type Function
1 CE Input Chip enable (RX/TX mode control)
2 CSN Input SPI chip select (active LOW)
3 SCK Input SPI clock (max 8MHz)
4 MOSI Input SPI data input
5 MISO Output SPI data output
6 IRQ Output Interrupt (active LOW)
7-8 VDD Power Supply (1.9-3.6V)
9-10 VSS Ground Ground
11-12 XC1/XC2 I/O 16 MHz crystal
13 VDD_PA Power Power amplifier supply (internal)
14 ANT1 I/O Antenna interface 1
15 ANT2 I/O Antenna interface 2
16-20 VDD/VSS Power Supply/Ground
Application Scenarios: In which products and applications is NRF24L01P used
  • Arduino wireless sensor node with 250kbps for maximum range
  • RC car remote control with 2Mbps for low latency
  • Smart home temperature sensor network with 1:6 star topology
  • Industrial equipment monitoring with auto-ACK and retransmission
Alternative Models: What chips are recommended as replacements for NRF24L01P
Manufacturer Part Number Package Notes
Nordic nRF24L01+ QFN-20 Updated version with + suffix
Nordic nRF52832-QFAA QFN-48 BLE + 2.4GHz SoC with MCU
TI CC2500RGPR QFN-20 2.4GHz, similar class, SPI
Silicon Labs SI24R1 QFN-20 Compatible clone, lower cost
HopeRF RFM75 Module Module with nRF24L01+ compatible

Recommend Parts

ISO1176TDWR

Isolated RS-485 transceiver, 40Mbps, integrated transformer driver, SOIC-16

Brand: TI

Package: SOIC-16 (DW, wide-body, 10.3 x 10.3 mm)

IN STOCK: 6874pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFB4020PBF

200V N-Channel HEXFET Power MOSFET, 31A, 68 mΩ RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 14149pcs

Cargo cycle: 3-7 Days

The minimum order is 1

NRF52832-QFAA-T

Nordic BLE SoC, ARM Cortex-M4 @ 64MHz, 64KB Flash, 32KB RAM, QFN-48

Package: See datasheet

IN STOCK: 10958pcs

Cargo cycle: 3-7 Days

The minimum order is 1

UCC28740DR

CVCC Flyback Controller, 700V startup, opto feedback, <10mW no-load, SOIC-7

Brand: TI

Package: SOIC-7 (4.9 x 3.9 x 1.75 mm)

IN STOCK: 4840pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MMUN2211LT1G

NPN digital transistor, R1=10kΩ R2=10kΩ, 50V, 100mA, SOT-23-3, pre-biased BRT switch

Brand: Onsemi

Package: SOT-23-3 (TO-236, SC-59)

IN STOCK: 8500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TMS320F2810PBKA

C2000 Delfino DSP controller, 150MHz, 128KB Flash, BGA-179

Brand: TI

Package: BGA-179 (16 x 16 mm, PBK package)

IN STOCK: 3124pcs

Cargo cycle: 3-7 Days

The minimum order is 1