Opens in a new tab

SN74HC595N

8-bit shift register with latch, 3-state, daisy-chain, PDIP-16

10000

Effective Inventory

Image for reference only

Manufacturer Part:

SN74HC595N

Package:

PDIP-16 (19.3 x 6.35 x 4.57mm, 2.54mm pitch, through-hole)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The SN74HC595N from Texas Instruments is an 8-bit serial-in/parallel-out shift register with output latch and 3-state outputs, controllable via just 3 MCU pins, in a 16-pin PDIP package.

Key Specifications

Function 8-bit shift register with output latch
Logic Family HC (High-speed CMOS)
Supply Voltage 2V to 6V
Shift Clock Frequency 52MHz typical @ 6V
Output Type 3-state (OE control)
Output Drive ±6mA @ 6V
Serial Data Input SER (pin 14)
Shift Clock SRCLK (pin 11, rising edge)
Latch Clock RCLK (pin 12, rising edge)
Output Enable OE (pin 13, active LOW)
Master Reset SRCLR (pin 10, active LOW)
Cascade Output Q7′ (pin 9, serial out for daisy-chain)
Operating Temperature -40°C to +85°C
Package PDIP-16 (19.3 x 6.35mm)

Features

  • 8-bit serial-to-parallel conversion
  • Separate shift and latch clocks
  • 3-state outputs for bus sharing
  • Daisy-chainable via Q7′ output
  • Asynchronous master reset (SRCLR)
  • Only 3 MCU pins needed for 8 outputs
  • Wide supply range: 2V to 6V

Applications

  • LED matrix column/row driver
  • 7-segment display multiplexing
  • Expanding MCU output pins
  • SPI-controlled parallel output
  • Cascaded display chains
Product Introduction: SN74HC595N Product Introduction

The SN74HC595N from Texas Instruments is an 8-bit serial-in/parallel-out shift register with an output latch and 3-state outputs, allowing a microcontroller to control 8 (or more, via daisy-chaining) output lines using only 3 GPIO pins: SER (data), SRCLK (shift clock), and RCLK (latch clock). The shift register and output latch are separate: data shifts through the 8-bit register on each rising edge of SRCLK, but the outputs don’t change until a rising edge on RCLK transfers the shift register contents to the output latch. This prevents output glitches during shifting. The Q7′ output provides the serial data that overflows from the 8th stage, connecting to the SER input of the next 595 for daisy-chaining — with two 595s, 3 MCU pins control 16 outputs. The 3-state outputs (controlled by OE) allow multiple 595s to share an output bus. The master reset (SRCLR) clears the shift register asynchronously. The N suffix denotes the PDIP-16 through-hole package.

Working Principle: SN74HC595N Working Principle

The SN74HC595N has two 8-bit registers: a shift register and an output (storage) register. On each rising edge of SRCLK, the serial data at SER is shifted into the first stage of the shift register, and all existing data shifts one position toward the output. After 8 clock cycles, the first bit shifted in appears at the last stage (Q7′) ready for the next chip in a daisy chain. The shift register contents are NOT directly connected to the output pins. When a rising edge occurs on RCLK, the entire 8-bit shift register is copied to the output latch, and the 8 output pins (Q0-Q7) update simultaneously. This two-stage architecture prevents the outputs from flickering during the shifting process. The output enable (OE, active LOW) controls the 3-state output buffers: when OE is HIGH, all outputs are high-impedance; when LOW, the latched data drives the outputs. The master reset (SRCLR, active LOW) clears the shift register to all zeros without affecting the output latch. To send 8 bits: (1) Shift in all 8 bits via SER and SRCLK, (2) Pulse RCLK HIGH to latch, (3) Set OE LOW to enable outputs. For daisy-chaining: after shifting 16 bits through two chips (the first 8 bits end up in the second chip), pulse RCLK once to latch both chips simultaneously.

Pin Description: SN74HC595N Pin Definition and Functions
Pin Name Type Description
1 Q1 Output Parallel output bit 1
2 Q2 Output Parallel output bit 2
3 Q3 Output Parallel output bit 3
4 Q4 Output Parallel output bit 4
5 Q5 Output Parallel output bit 5
6 Q6 Output Parallel output bit 6
7 Q7 Output Parallel output bit 7
8 GND Power Ground
9 Q7′ Output Serial output (for daisy-chain to next SER)
10 SRCLR Input Shift register clear (active LOW)
11 SRCLK Input Shift register clock (rising edge)
12 RCLK Input Storage register clock (rising edge, latch)
13 OE Input Output enable (active LOW; HIGH = 3-state)
14 SER Input Serial data input
15 Q0 Output Parallel output bit 0
16 VCC Power Supply (2V to 6V)
Application Scenarios: In which products and applications is SN74HC595N used
  • 8-LED Control: MCU SPI → SER+SRCLK; 8 bits shifted in; RCLK pulse latches; 8 LEDs on Q0-Q7; only 3 pins used
  • Daisy Chain (16+ outputs): Q7′ of first → SER of second; shift 16 bits; one RCLK pulse; 3 pins control 16+ outputs
  • 7-Segment Display: 595 drives 7 segments + decimal point; multiplex with another 595 for digit select; 3 pins for 4+ digits
  • LED Matrix: Row 595 + Column 595; shift row and column data; 6 pins (3 per 595) control 8×8=64 LEDs
  • Relay Board: 8 relays on Q0-Q7; 3 pins from MCU; ULN2803 between 595 and relay coils for current
Alternative Models: What chips are recommended as replacements for SN74HC595N
Model Manufacturer Key Difference Package Supply
74HC595D TI/Nexperia CMOS version with wide 2-6V supply range, lower power consumption and higher noise immunity SOIC-16 2-6V CMOS
74HC595N TI/Nexperia Through-hole DIP version of HC family for prototyping and repair DIP-16 2-6V CMOS
74HCT595D TI/Nexperia CMOS with TTL-compatible input levels, ideal for mixing with LS devices at 5V SOIC-16 4.5-5.5V TTL-in
74HCT595N TI/Nexperia Through-hole DIP version of HCT family for prototyping and repair DIP-16 4.5-5.5V TTL-in
74LVC595D TI/Nexperia Low-voltage CMOS for 1.65-3.6V modern logic with 24mA output drive and bus-hold inputs SOIC-16 1.65-3.6V CMOS
74LVC595N TI/Nexperia Through-hole DIP version of LVC family for prototyping and repair DIP-16 1.65-3.6V CMOS
74AUP595D TI/Nexperia Ultra-low power CMOS with 0.8-3.6V supply for battery-powered and mobile applications SOIC-16 0.8-3.6V CMOS
74AUP595N TI/Nexperia Through-hole DIP version of AUP family for prototyping and repair DIP-16 0.8-3.6V CMOS

The 74595 is a 8-Bit Shift Register with Output Latches and 3-State Output. Family variants span from the original LS TTL (5V only) to modern LVC/AUP (down to 0.8V). HC and HCT versions offer 2-6V CMOS operation with HCT providing TTL-compatible input thresholds for mixed 5V systems. CD4000-series equivalents offer the widest 3-18V supply range at the cost of lower switching speed. DIP packages (N suffix) are through-hole; SOIC (D suffix) and TSSOP are surface-mount.

Recommend Parts

0751.0505

Schurter fuse, 0751.0505

Brand: schurter

Package: See datasheet

IN STOCK: 6768pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TL062CDR

Low-power JFET-input dual op-amp, 1MHz GBW, 30pA Ibias, SOIC-8, ±3.5V to ±18V

Brand: TI

Package: SOIC-8 (3.9 x 4.9 x 1.75mm)

IN STOCK: 11576pcs

Cargo cycle: 3-7 Days

The minimum order is 1

P89LPC922FN

8-bit 80C51 MCU, 8KB Flash, 256B RAM, 20-SSOP

Brand: NXP

Package: SSOP-20 (7.2 x 5.3 mm)

IN STOCK: 12628pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AC0603JR-070RL

Chip Resistor, 0Ω (Zero Ohm Jumper), ±5%, 0603 (1608 Metric), 1/10W (100mW)

Brand: Yageo

Package: 0603 (1608 Metric)

IN STOCK: 100000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LMR34206FSC5RNXRQ1

42V 2A sync buck, 5V fixed, 2.2MHz, 18uA Iq, AEC-Q100, SOT-563

Brand: TI

Package: SOT-563 (1.6 x 1.2 x 0.55mm)

IN STOCK: 6500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AO3402

30V N-channel trench MOSFET, SOT-23, 4A, RDS(on) 52m ohm max @ 10V, Qg 10nC, 2.5V gate drive capable, -55C to +150C.

Brand: aosmd

Package: SOT-23 (2.9 x 1.6 x 1.25mm)

IN STOCK: 14066pcs

Cargo cycle: 3-7 Days

The minimum order is 1