Opens in a new tab

SN74LS04N

Hex inverter, 6 NOT gates, LS TTL, 10ns, PDIP-14

20000

Effective Inventory

Image for reference only

Manufacturer Part:

SN74LS04N

Package:

PDIP-14 (19.3 x 6.35 x 4.57mm, 2.54mm pitch, through-hole)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The SN74LS04N is a hex inverter from Texas Instruments with six independent NOT gates in a 14-pin PDIP package, using LS (Low-power Schottky) TTL technology.

Key Specifications

Number of Gates 6 (hex inverter)
Logic Family LS (Low-power Schottky)
Supply Voltage 4.75V to 5.25V (5V nominal)
Propagation Delay 10ns typical
Output Low Current (IOL) 8mA
Output High Current (IOH) -0.4mA
Supply Current (all gates) 6.1mA typical, 12mA max
Input Voltage (HIGH min) 2.0V
Input Voltage (LOW max) 0.8V
Operating Temperature 0°C to +70°C
Package PDIP-14 (19.3 x 6.35mm)

Features

  • Six independent inverters in one package
  • LS TTL technology for fast switching
  • 10ns typical propagation delay
  • Input clamp diodes for undershoot protection
  • Direct replacement for 7404 and 74LS04
  • Industry-standard pinout

Applications

  • Logic signal inversion
  • Clock signal complement generation
  • Active-low to active-high conversion
  • Simple oscillator with crystal or RC network
  • Logic buffer with inversion
Product Introduction: SN74LS04N Product Introduction

The SN74LS04N from Texas Instruments contains six independent logic inverters (NOT gates) in a 14-pin PDIP through-hole package. Each inverter performs the Boolean function Y = NOT(A), producing a LOW output when the input is HIGH and a HIGH output when the input is LOW. The LS (Low-power Schottky) technology provides 10ns typical propagation delay with only 6.1mA typical supply current for all six gates. Input clamp diodes protect against negative voltage undershoot. The device is a direct replacement for the classic 7404 and 74LS04 from any manufacturer, using the industry-standard pinout where each gate has its input on an odd pin and its output on the adjacent even pin. The N suffix denotes the PDIP-14 through-hole package.

Working Principle: SN74LS04N Working Principle

Each of the six inverters in the SN74LS04N is a simple single-input logic gate that performs the NOT function. When the input voltage is at a logic HIGH level (above 2.0V), the output drives LOW (typically 0.2V, max 0.4V at 8mA sink). When the input is at a logic LOW level (below 0.8V), the output drives HIGH (typically 3.4V, min 2.7V at -0.4mA source). The totem-pole output stage can actively drive both HIGH and LOW levels, unlike open-collector outputs that require external pull-up resistors. The 10ns propagation delay means the output transitions approximately 10ns after the input crosses the switching threshold. The six gates are completely independent—each can be used for a different function in the circuit. Common configurations include: (1) single inversion, (2) double inversion (two gates in series) as a buffer/delay element, (3) three gates in series for odd inversion + delay, and (4) two gates with feedback for a simple oscillator.

Pin Description: SN74LS04N Pin Definition and Functions
Pin Name Type Description
1 1A Input Gate 1 input
2 1Y Output Gate 1 output (inverted)
3 2A Input Gate 2 input
4 2Y Output Gate 2 output (inverted)
5 3A Input Gate 3 input
6 3Y Output Gate 3 output (inverted)
7 GND Power Ground
8 4Y Output Gate 4 output (inverted)
9 4A Input Gate 4 input
10 5Y Output Gate 5 output (inverted)
11 5A Input Gate 5 input
12 6Y Output Gate 6 output (inverted)
13 6A Input Gate 6 input
14 VCC Power Supply (4.75V to 5.25V)

SN74LS04N uses the PDIP-14 package with standard hex inverter pinout: VCC at Pin 14, GND at Pin 7. Six independent inverters: Inv 1 (Pin 1 in, Pin 2 out), Inv 2 (Pin 3 in, Pin 4 out), Inv 3 (Pin 5 in, Pin 6 out), Inv 4 (Pin 9 in, Pin 8 out), Inv 5 (Pin 11 in, Pin 10 out), Inv 6 (Pin 13 in, Pin 12 out). This is the most widely used pinout for 14-pin hex inverters across all logic families. For Schmitt-trigger version, use SN74LS14N. For open-collector, use SN74LS05N. Propagation delay is typically 10ns for LS technology at 5V supply.

Application Scenarios: In which products and applications is SN74LS04N used
  • Signal Inversion: Convert active-HIGH to active-LOW signals for driving active-LOW chip selects or enable pins
  • Clock Complement: Generate complementary clock for push-pull or H-bridge gate drive
  • Crystal Oscillator: Two inverters with feedback crystal and capacitors form a Pierce oscillator
  • RC Oscillator: Two inverters with resistor feedback and RC timing create a simple square-wave generator
  • Logic Delay: Two gates in series provide ~20ns delay without inversion; useful for timing alignment
Alternative Models: What chips are recommended as replacements for SN74LS04N
Model Manufacturer Key Difference Package Supply
74LS04N TI/Nexperia Original TTL version with 5V-only supply, typical propagation delay 10-15ns DIP-14 5V TTL
74LS04D TI/Nexperia Surface-mount SOIC version of LS with identical logic function SOIC-14 5V TTL
74HC04D TI/Nexperia CMOS version with wide 2-6V supply range, lower power consumption and higher noise immunity SOIC-14 2-6V CMOS
74HC04N TI/Nexperia Through-hole DIP version of HC family for prototyping and repair DIP-14 2-6V CMOS
74HCT04D TI/Nexperia CMOS with TTL-compatible input levels, ideal for mixing with LS devices at 5V SOIC-14 4.5-5.5V TTL-in
74HCT04N TI/Nexperia Through-hole DIP version of HCT family for prototyping and repair DIP-14 4.5-5.5V TTL-in
74AC04D TI/Nexperia Advanced CMOS with 2-6V supply and higher output drive current (24mA vs 6mA for HC) SOIC-14 2-6V CMOS
74AC04N TI/Nexperia Through-hole DIP version of AC family for prototyping and repair DIP-14 2-6V CMOS
74LVC04D TI/Nexperia Low-voltage CMOS for 1.65-3.6V modern logic with 24mA output drive and bus-hold inputs SOIC-14 1.65-3.6V CMOS
74LVC04N TI/Nexperia Through-hole DIP version of LVC family for prototyping and repair DIP-14 1.65-3.6V CMOS
74AUP04D TI/Nexperia Ultra-low power CMOS with 0.8-3.6V supply for battery-powered and mobile applications SOIC-14 0.8-3.6V CMOS
74AUP04N TI/Nexperia Through-hole DIP version of AUP family for prototyping and repair DIP-14 0.8-3.6V CMOS

The 7404 is a Hex Inverter. Family variants span from the original LS TTL (5V only) to modern LVC/AUP (down to 0.8V). HC and HCT versions offer 2-6V CMOS operation with HCT providing TTL-compatible input thresholds for mixed 5V systems. CD4000-series equivalents offer the widest 3-18V supply range at the cost of lower switching speed. DIP packages (N suffix) are through-hole; SOIC (D suffix) and TSSOP are surface-mount.

Recommend Parts

0751.0505

Schurter fuse, 0751.0505

Brand: schurter

Package: See datasheet

IN STOCK: 6768pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TL062CDR

Low-power JFET-input dual op-amp, 1MHz GBW, 30pA Ibias, SOIC-8, ±3.5V to ±18V

Brand: TI

Package: SOIC-8 (3.9 x 4.9 x 1.75mm)

IN STOCK: 11576pcs

Cargo cycle: 3-7 Days

The minimum order is 1

P89LPC922FN

8-bit 80C51 MCU, 8KB Flash, 256B RAM, 20-SSOP

Brand: NXP

Package: SSOP-20 (7.2 x 5.3 mm)

IN STOCK: 12628pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AC0603JR-070RL

Chip Resistor, 0Ω (Zero Ohm Jumper), ±5%, 0603 (1608 Metric), 1/10W (100mW)

Brand: Yageo

Package: 0603 (1608 Metric)

IN STOCK: 100000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LMR34206FSC5RNXRQ1

42V 2A sync buck, 5V fixed, 2.2MHz, 18uA Iq, AEC-Q100, SOT-563

Brand: TI

Package: SOT-563 (1.6 x 1.2 x 0.55mm)

IN STOCK: 6500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AO3402

30V N-channel trench MOSFET, SOT-23, 4A, RDS(on) 52m ohm max @ 10V, Qg 10nC, 2.5V gate drive capable, -55C to +150C.

Brand: aosmd

Package: SOT-23 (2.9 x 1.6 x 1.25mm)

IN STOCK: 14066pcs

Cargo cycle: 3-7 Days

The minimum order is 1