Opens in a new tab

SN74LS175N

Quad D flip-flop, edge-triggered, Q+Q̅, common CLK/CLR, PDIP-16

4200

Effective Inventory

Image for reference only

Manufacturer Part:

SN74LS175N

Package:

PDIP-16 (19.3 x 6.35 x 4.57mm, 2.54mm pitch, through-hole)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The SN74LS175N from Texas Instruments is a quad D-type flip-flop with complementary outputs, common clock and clear inputs, and edge-triggered operation in a 16-pin PDIP package.

Key Specifications

Number of Flip-Flops 4 (quad D-type)
Logic Family LS (Low-power Schottky)
Supply Voltage 4.75V to 5.25V (5V nominal)
Trigger Type Positive-edge triggered (rising edge of CLK)
Outputs True (Q) and complementary (Q̅) per flip-flop
Propagation Delay (CLK to Q) 25ns typical
Maximum Clock Frequency 30MHz typical
Setup Time 15ns minimum before clock edge
Hold Time 0ns minimum after clock edge
Clear (CLR) Active-low, asynchronous, overrides all
Operating Temperature 0°C to +70°C
Package PDIP-16 (19.3 x 6.35mm)

Features

  • Four D-type edge-triggered flip-flops
  • Complementary outputs (Q and Q̅)
  • Common clock input for all four flip-flops
  • Asynchronous clear (active-low)
  • 30MHz maximum clock frequency
  • Zero hold time simplifies design

Applications

  • Parallel data register
  • Data synchronization and capture
  • Address latching
  • Frequency division
  • Digital delay elements
Product Introduction: SN74LS175N Product Introduction

The SN74LS175N from Texas Instruments contains four D-type positive-edge-triggered flip-flops with a common clock (CLK) and common asynchronous clear (CLR) input. Each flip-flop has both true (Q) and complementary (Q̅) outputs. On the rising edge of CLK, the data at each D input is transferred to the corresponding Q output. The asynchronous CLR input, when LOW, immediately resets all Q outputs to LOW regardless of the clock or D inputs. The complementary outputs are useful for generating both active-HIGH and active-LOW versions of a stored signal without additional inverters. The 30MHz maximum clock frequency and 15ns setup time make it suitable for moderate-speed digital systems. The zero hold time simplifies cascading with other TTL logic. The N suffix denotes the PDIP-16 through-hole package.

Working Principle: SN74LS175N Working Principle

Each of the four D-type flip-flops in the SN74LS175N captures the logic level at its D input on the rising edge of the common CLK signal. The captured value appears at the Q output, and the inverted value appears at the Q̅ output. Between clock edges, the outputs hold their previous values regardless of changes on the D inputs. The setup time requirement (15ns minimum) means the D input must be stable for at least 15ns before the clock edge for reliable capture. The zero hold time means the D input can change immediately after the clock edge without risk of metastability. The asynchronous clear (CLR) overrides everything: when CLR goes LOW, all Q outputs immediately go LOW, regardless of CLK or D. When CLR is HIGH, the flip-flops operate normally on clock edges. In a parallel data register application, four data bits are presented to the D inputs, and a single clock edge captures all four simultaneously. This is useful for sampling a parallel bus, synchronizing asynchronous inputs to the system clock, or creating a pipeline stage.

Pin Description: SN74LS175N Pin Definition and Functions
Pin Name Type Description
1 CLR Input Asynchronous clear (active LOW, resets all Q to LOW)
2 1Q Output Flip-flop 1 true output
3 1Q̅ Output Flip-flop 1 complementary output
4 1D Input Flip-flop 1 data input
5 2D Input Flip-flop 2 data input
6 2Q̅ Output Flip-flop 2 complementary output
7 2Q Output Flip-flop 2 true output
8 GND Power Ground
9 CLK Input Clock (rising edge triggers data capture)
10 3Q Output Flip-flop 3 true output
11 3Q̅ Output Flip-flop 3 complementary output
12 3D Input Flip-flop 3 data input
13 4D Input Flip-flop 4 data input
14 4Q̅ Output Flip-flop 4 complementary output
15 4Q Output Flip-flop 4 true output
16 VCC Power Supply (4.75V to 5.25V)
Application Scenarios: In which products and applications is SN74LS175N used
  • Parallel Register: 4-bit data bus → D inputs; CLK edge captures all 4 bits simultaneously; Q outputs hold data for downstream logic
  • Synchronizer: Asynchronous inputs → D; CLK = system clock; Q outputs are synchronous to clock domain
  • Address Latch: Multiplexed address/data bus → D; ALE signal → CLK; Q holds address during data phase
  • Frequency ÷2: Connect Q̅ to D; CLK input = input frequency; Q output = half frequency (toggle mode)
  • Digital Delay: Chain of 175s; data passes through each register on successive clock edges; 4-clock delay per stage
Alternative Models: What chips are recommended as replacements for SN74LS175N
Model Manufacturer Key Difference Package Supply
74LS175N TI/Nexperia Original TTL version with 5V-only supply, typical propagation delay 10-15ns DIP-16 5V TTL
74LS175D TI/Nexperia Surface-mount SOIC version of LS with identical logic function SOIC-16 5V TTL
74HC175D TI/Nexperia CMOS version with wide 2-6V supply range, lower power consumption and higher noise immunity SOIC-16 2-6V CMOS
74HC175N TI/Nexperia Through-hole DIP version of HC family for prototyping and repair DIP-16 2-6V CMOS
74HCT175D TI/Nexperia CMOS with TTL-compatible input levels, ideal for mixing with LS devices at 5V SOIC-16 4.5-5.5V TTL-in
74HCT175N TI/Nexperia Through-hole DIP version of HCT family for prototyping and repair DIP-16 4.5-5.5V TTL-in
74LVC175D TI/Nexperia Low-voltage CMOS for 1.65-3.6V modern logic with 24mA output drive and bus-hold inputs SOIC-16 1.65-3.6V CMOS
74LVC175N TI/Nexperia Through-hole DIP version of LVC family for prototyping and repair DIP-16 1.65-3.6V CMOS

The 74175 is a Quad D-Type Flip-Flop with Clear. Family variants span from the original LS TTL (5V only) to modern LVC/AUP (down to 0.8V). HC and HCT versions offer 2-6V CMOS operation with HCT providing TTL-compatible input thresholds for mixed 5V systems. CD4000-series equivalents offer the widest 3-18V supply range at the cost of lower switching speed. DIP packages (N suffix) are through-hole; SOIC (D suffix) and TSSOP are surface-mount.

Recommend Parts

0751.0505

Schurter fuse, 0751.0505

Brand: schurter

Package: See datasheet

IN STOCK: 6768pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TL062CDR

Low-power JFET-input dual op-amp, 1MHz GBW, 30pA Ibias, SOIC-8, ±3.5V to ±18V

Brand: TI

Package: SOIC-8 (3.9 x 4.9 x 1.75mm)

IN STOCK: 11576pcs

Cargo cycle: 3-7 Days

The minimum order is 1

P89LPC922FN

8-bit 80C51 MCU, 8KB Flash, 256B RAM, 20-SSOP

Brand: NXP

Package: SSOP-20 (7.2 x 5.3 mm)

IN STOCK: 12628pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AC0603JR-070RL

Chip Resistor, 0Ω (Zero Ohm Jumper), ±5%, 0603 (1608 Metric), 1/10W (100mW)

Brand: Yageo

Package: 0603 (1608 Metric)

IN STOCK: 100000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LMR34206FSC5RNXRQ1

42V 2A sync buck, 5V fixed, 2.2MHz, 18uA Iq, AEC-Q100, SOT-563

Brand: TI

Package: SOT-563 (1.6 x 1.2 x 0.55mm)

IN STOCK: 6500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AO3402

30V N-channel trench MOSFET, SOT-23, 4A, RDS(on) 52m ohm max @ 10V, Qg 10nC, 2.5V gate drive capable, -55C to +150C.

Brand: aosmd

Package: SOT-23 (2.9 x 1.6 x 1.25mm)

IN STOCK: 14066pcs

Cargo cycle: 3-7 Days

The minimum order is 1