Opens in a new tab

SN74LS245N

Octal bus transceiver, 3-state, DIR/OE, 24mA, LS TTL, PDIP-20

6500

Effective Inventory

Image for reference only

Manufacturer Part:

SN74LS245N

Package:

PDIP-20 (24.33 x 6.35 x 5.08mm, 2.54mm pitch, through-hole)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The SN74LS245N is an octal bus transceiver with 3-state outputs from Texas Instruments, designed for bidirectional data transfer between buses with direction and output enable controls in a 20-pin PDIP package.

Key Specifications

Number of Channels 8 (octal bidirectional)
Logic Family LS (Low-power Schottky)
Supply Voltage 4.75V to 5.25V (5V nominal)
Output Type 3-state (high-impedance when disabled)
Direction Control DIR pin (HIGH = A→B, LOW = B→A)
Output Enable OE (active-low; both DIR directions disabled when HIGH)
Propagation Delay 12ns typical @ 5V
Output Drive (IOL) 24mA (bus driver)
Input Hysteresis Yes (improved noise margin)
Operating Temperature 0°C to +70°C
Package PDIP-20 (24.33 x 6.35mm)

Features

  • 8-bit bidirectional bus transceiver
  • 3-state outputs for bus sharing
  • Direction control: DIR selects A-to-B or B-to-A
  • Output enable: OE disables both directions
  • 24mA output sink current (bus driver capability)
  • Input hysteresis for improved noise margin
  • Standard 74LS245 pinout

Applications

  • Microprocessor bus transceiver
  • Bidirectional data bus buffering
  • Bus-to-bus data transfer
  • Memory interface buffering
  • Backplane bus driver
Product Introduction: SN74LS245N Product Introduction

The SN74LS245N from Texas Instruments is an octal bidirectional bus transceiver with 3-state outputs, designed for asynchronous two-way communication between data buses. The DIR (direction) pin controls data flow: DIR=HIGH transmits data from the A bus to the B bus, and DIR=LOW transmits from B to A. The OE (output enable) pin, when HIGH, places both A and B outputs in the high-impedance state, effectively disconnecting the transceiver from both buses. When OE is LOW, the selected direction is enabled. The 24mA output sink current provides the drive strength needed for heavily loaded bus lines with multiple TTL inputs. Input hysteresis improves noise margin on the control and data inputs, reducing susceptibility to noise on long bus traces. The N suffix denotes the PDIP-20 through-hole package.

Working Principle: SN74LS245N Working Principle

The SN74LS245N contains eight bidirectional transceiver cells, each consisting of two non-inverting buffers with 3-state outputs connected back-to-back (one A-to-B, one B-to-A). The DIR input controls which set of buffers is active: DIR=HIGH enables the A-to-B buffers and disables the B-to-A buffers; DIR=LOW does the reverse. The OE input, when HIGH, overrides DIR and disables all 16 output buffers (both directions), placing both A and B ports in the high-impedance state. When OE is LOW, the direction selected by DIR is active. The A port and B port are symmetric; the device does not distinguish between them except by the DIR setting. In a typical microprocessor system, the SN74LS245N connects the CPU data bus to a peripheral bus. The CPU controls DIR based on the R/W signal, and OE is gated with the chip-select decode. When the CPU writes, DIR=HIGH and data flows from A (CPU side) to B (peripheral side). When the CPU reads, DIR=LOW and data flows from B to A. When the peripheral is not selected, OE=HIGH disconnects the transceiver from both buses, preventing bus contention.

Pin Description: SN74LS245N Pin Definition and Functions
Pin Name Type Description
1 DIR Input Direction (HIGH=A→B, LOW=B→A)
2-9 A1-A8 I/O A bus data (bidirectional, 3-state)
10 GND Power Ground
11-18 B8-B1 I/O B bus data (bidirectional, 3-state)
19 OE Input Output enable (active-low; HIGH=both disabled)
20 VCC Power Supply (4.75V to 5.25V)

SN74LS245N uses the PDIP-20 package: VCC at Pin 20, GND at Pin 10. Eight bidirectional data lines: A0-A7 on Pins 2-9 (side A), B0-B7 on Pins 18-11 (side B). Pin 1 = DIR (direction control: HIGH = A→B, LOW = B→A). Pin 19 = OE (Output Enable, active-low). When OE is HIGH, all outputs are in high-impedance state regardless of DIR. The two-enable architecture (DIR + OE) allows simple bidirectional bus control with just two control signals. This pinout is shared by 74HC245, 74HCT245, and 74LVC245 octal transceivers. For 3.3V systems, 74LVC245APW provides the same function in TSSOP-20. The A-side and B-side pins are symmetrically arranged for clean bus routing.

Application Scenarios: In which products and applications is SN74LS245N used
  • CPU Bus Buffer: DIR=R/W signal; OE=chip select; 24mA drives multiple TTL loads on the data bus
  • Backplane Driver: 3-state isolation allows multiple boards to share a common backplane bus
  • Level Translation: A bus at 5V, B bus at 3.3V through current-limiting resistors (unidirectional per cycle)
  • Bus Isolation: OE=HIGH isolates subsystem during debug or hot-swap; DIR selects read/write direction
  • Memory Interface: Bidirectional buffer between CPU data bus and memory data pins; DIR from MEMR/MEMW
Alternative Models: What chips are recommended as replacements for SN74LS245N
Model Manufacturer Key Difference Package Supply
74LS245N TI/Nexperia Original TTL version with 5V-only supply, typical propagation delay 10-15ns DIP-20 5V TTL
74LS245D TI/Nexperia Surface-mount SOIC version of LS with identical logic function SOIC-20 5V TTL
74HC245D TI/Nexperia CMOS version with wide 2-6V supply range, lower power consumption and higher noise immunity SOIC-20 2-6V CMOS
74HC245N TI/Nexperia Through-hole DIP version of HC family for prototyping and repair DIP-20 2-6V CMOS
74HCT245D TI/Nexperia CMOS with TTL-compatible input levels, ideal for mixing with LS devices at 5V SOIC-20 4.5-5.5V TTL-in
74HCT245N TI/Nexperia Through-hole DIP version of HCT family for prototyping and repair DIP-20 4.5-5.5V TTL-in
74LVC245D TI/Nexperia Low-voltage CMOS for 1.65-3.6V modern logic with 24mA output drive and bus-hold inputs SOIC-20 1.65-3.6V CMOS
74LVC245N TI/Nexperia Through-hole DIP version of LVC family for prototyping and repair DIP-20 1.65-3.6V CMOS
74AUP245D TI/Nexperia Ultra-low power CMOS with 0.8-3.6V supply for battery-powered and mobile applications SOIC-20 0.8-3.6V CMOS
74AUP245N TI/Nexperia Through-hole DIP version of AUP family for prototyping and repair DIP-20 0.8-3.6V CMOS

The 74245 is a Octal Bus Transceiver with 3-State Output. Family variants span from the original LS TTL (5V only) to modern LVC/AUP (down to 0.8V). HC and HCT versions offer 2-6V CMOS operation with HCT providing TTL-compatible input thresholds for mixed 5V systems. CD4000-series equivalents offer the widest 3-18V supply range at the cost of lower switching speed. DIP packages (N suffix) are through-hole; SOIC (D suffix) and TSSOP are surface-mount.

Recommend Parts

0751.0505

Schurter fuse, 0751.0505

Brand: schurter

Package: See datasheet

IN STOCK: 6768pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TL062CDR

Low-power JFET-input dual op-amp, 1MHz GBW, 30pA Ibias, SOIC-8, ±3.5V to ±18V

Brand: TI

Package: SOIC-8 (3.9 x 4.9 x 1.75mm)

IN STOCK: 11576pcs

Cargo cycle: 3-7 Days

The minimum order is 1

P89LPC922FN

8-bit 80C51 MCU, 8KB Flash, 256B RAM, 20-SSOP

Brand: NXP

Package: SSOP-20 (7.2 x 5.3 mm)

IN STOCK: 12628pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AC0603JR-070RL

Chip Resistor, 0Ω (Zero Ohm Jumper), ±5%, 0603 (1608 Metric), 1/10W (100mW)

Brand: Yageo

Package: 0603 (1608 Metric)

IN STOCK: 100000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LMR34206FSC5RNXRQ1

42V 2A sync buck, 5V fixed, 2.2MHz, 18uA Iq, AEC-Q100, SOT-563

Brand: TI

Package: SOT-563 (1.6 x 1.2 x 0.55mm)

IN STOCK: 6500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AO3402

30V N-channel trench MOSFET, SOT-23, 4A, RDS(on) 52m ohm max @ 10V, Qg 10nC, 2.5V gate drive capable, -55C to +150C.

Brand: aosmd

Package: SOT-23 (2.9 x 1.6 x 1.25mm)

IN STOCK: 14066pcs

Cargo cycle: 3-7 Days

The minimum order is 1