Opens in a new tab

SN74LS373N

Octal transparent latch, 3-state, LE/OE, PDIP-20

4800

Effective Inventory

Image for reference only

Manufacturer Part:

SN74LS373N

Package:

PDIP-20 (24.33 x 6.35 x 5.08mm, 2.54mm pitch, through-hole)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The SN74LS373N from Texas Instruments is an octal transparent D-type latch with 3-state outputs, controlled by a single latch enable and output enable, in a 20-pin PDIP package.

Key Specifications

Number of Latches 8 (octal)
Logic Family LS (Low-power Schottky)
Supply Voltage 4.75V to 5.25V (5V nominal)
Latch Enable (LE) Transparent when HIGH, latched when LOW
Output Enable (OE) Active-low; HIGH = 3-state (high impedance)
Output Type 3-state (for bus sharing)
Propagation Delay 18ns typical (D to Q, LE=HIGH)
Latch Hold Time 10ns minimum
Operating Temperature 0°C to +70°C
Package PDIP-20 (24.33 x 6.35mm)

Features

  • 8-bit transparent D-type latch
  • 3-state outputs for bus driving
  • Single latch enable for all 8 bits
  • Output enable for bus sharing
  • 18ns typical propagation delay
  • Industry-standard 74373 pinout

Applications

  • Address latch for multiplexed bus
  • Output port expansion
  • Data capture and hold
  • Bus buffering and isolation
  • Microprocessor I/O latching
Product Introduction: SN74LS373N Product Introduction

The SN74LS373N from Texas Instruments is an octal transparent D-type latch with 3-state outputs, commonly used for address latching on multiplexed address/data buses such as the Intel 8051 microcontroller. When the latch enable (LE) is HIGH, the eight D inputs pass transparently to the Q outputs. When LE transitions from HIGH to LOW, the current data is latched (held) on the Q outputs, and further changes on D are ignored. The output enable (OE) is active-low; when OE is HIGH, all eight outputs are in the high-impedance state, effectively disconnecting the latch from the bus. When OE is LOW, the latched data appears on the outputs. The transparent mode (LE=HIGH) allows the latch to function as a buffer, while the latched mode (LE=LOW) holds data for downstream circuitry. The 3-state outputs allow multiple 373s to share a common bus. The N suffix denotes the PDIP-20 through-hole package.

Working Principle: SN74LS373N Working Principle

The SN74LS373N contains eight identical D-type latches. When the latch enable (LE) is HIGH, each latch is transparent: the Q output follows the D input. When LE goes LOW, each latch captures the D input value present at the LE transition and holds it. While LE is LOW, changes on D do not affect Q. This transparent-then-latch behavior is essential for multiplexed bus systems: the address and data share the same physical bus lines, and the 373 captures the address during the address phase of the bus cycle so that the address remains stable while the data phase uses the same bus lines. The output enable (OE) controls the 3-state output buffers: when OE is LOW, the latched Q values drive the output pins; when OE is HIGH, the outputs are high-impedance (floating), allowing other devices to drive the bus. The 10ns latch hold time means the D input must be stable for at least 10ns after LE goes LOW for reliable latching. In an 8051 system, the ALE (Address Latch Enable) signal connects to LE; ALE goes HIGH during the address phase (allowing address to pass through to the latch) and goes LOW to latch the address before the data phase begins.

Pin Description: SN74LS373N Pin Definition and Functions
Pin Name Type Description
1 OE Input Output enable (active LOW; HIGH=3-state)
2 1Q Output Latch 1 output (3-state)
3 1D Input Latch 1 data input
4 2D Input Latch 2 data input
5 2Q Output Latch 2 output (3-state)
6 3Q Output Latch 3 output (3-state)
7 3D Input Latch 3 data input
8 4D Input Latch 4 data input
9 4Q Output Latch 4 output (3-state)
10 GND Power Ground
11 LE Input Latch enable (HIGH=transparent, LOW=latched)
12 5Q Output Latch 5 output (3-state)
13 5D Input Latch 5 data input
14 6D Input Latch 6 data input
15 6Q Output Latch 6 output (3-state)
16 7Q Output Latch 7 output (3-state)
17 7D Input Latch 7 data input
18 8D Input Latch 8 data input
19 8Q Output Latch 8 output (3-state)
20 VCC Power Supply (4.75V to 5.25V)
Application Scenarios: In which products and applications is SN74LS373N used
  • 8051 Address Latch: AD0-AD7 → D0-D7; ALE → LE; Q0-Q7 → address bus; latches address when ALE falls
  • Output Port: D from data bus; LE from /WR + /CS; OE always LOW; latched outputs drive peripherals
  • Input Capture: External data → D; LE from control signal; captures snapshot of 8-bit data on LE falling edge
  • Bus Isolation: OE controlled by system; disconnects latch from bus when not addressed; multiple 373s share one bus
  • Pipeline Stage: LE from system clock; captures data on one phase, holds for next; 8-bit pipeline register
Alternative Models: What chips are recommended as replacements for SN74LS373N
Model Manufacturer Key Difference Package Supply
74LS373N TI/Nexperia Original TTL version with 5V-only supply, typical propagation delay 10-15ns DIP-20 5V TTL
74LS373D TI/Nexperia Surface-mount SOIC version of LS with identical logic function SOIC-20 5V TTL
74HC373D TI/Nexperia CMOS version with wide 2-6V supply range, lower power consumption and higher noise immunity SOIC-20 2-6V CMOS
74HC373N TI/Nexperia Through-hole DIP version of HC family for prototyping and repair DIP-20 2-6V CMOS
74HCT373D TI/Nexperia CMOS with TTL-compatible input levels, ideal for mixing with LS devices at 5V SOIC-20 4.5-5.5V TTL-in
74HCT373N TI/Nexperia Through-hole DIP version of HCT family for prototyping and repair DIP-20 4.5-5.5V TTL-in
74LVC373D TI/Nexperia Low-voltage CMOS for 1.65-3.6V modern logic with 24mA output drive and bus-hold inputs SOIC-20 1.65-3.6V CMOS
74LVC373N TI/Nexperia Through-hole DIP version of LVC family for prototyping and repair DIP-20 1.65-3.6V CMOS

The 74373 is a Octal Transparent Latch with 3-State Output. Family variants span from the original LS TTL (5V only) to modern LVC/AUP (down to 0.8V). HC and HCT versions offer 2-6V CMOS operation with HCT providing TTL-compatible input thresholds for mixed 5V systems. CD4000-series equivalents offer the widest 3-18V supply range at the cost of lower switching speed. DIP packages (N suffix) are through-hole; SOIC (D suffix) and TSSOP are surface-mount.

Recommend Parts

0751.0505

Schurter fuse, 0751.0505

Brand: schurter

Package: See datasheet

IN STOCK: 6768pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TL062CDR

Low-power JFET-input dual op-amp, 1MHz GBW, 30pA Ibias, SOIC-8, ±3.5V to ±18V

Brand: TI

Package: SOIC-8 (3.9 x 4.9 x 1.75mm)

IN STOCK: 11576pcs

Cargo cycle: 3-7 Days

The minimum order is 1

P89LPC922FN

8-bit 80C51 MCU, 8KB Flash, 256B RAM, 20-SSOP

Brand: NXP

Package: SSOP-20 (7.2 x 5.3 mm)

IN STOCK: 12628pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AC0603JR-070RL

Chip Resistor, 0Ω (Zero Ohm Jumper), ±5%, 0603 (1608 Metric), 1/10W (100mW)

Brand: Yageo

Package: 0603 (1608 Metric)

IN STOCK: 100000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LMR34206FSC5RNXRQ1

42V 2A sync buck, 5V fixed, 2.2MHz, 18uA Iq, AEC-Q100, SOT-563

Brand: TI

Package: SOT-563 (1.6 x 1.2 x 0.55mm)

IN STOCK: 6500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AO3402

30V N-channel trench MOSFET, SOT-23, 4A, RDS(on) 52m ohm max @ 10V, Qg 10nC, 2.5V gate drive capable, -55C to +150C.

Brand: aosmd

Package: SOT-23 (2.9 x 1.6 x 1.25mm)

IN STOCK: 14066pcs

Cargo cycle: 3-7 Days

The minimum order is 1