Opens in a new tab

SN74LS373N

Octal transparent D-latch, 3-state out, single LE/OE, LS TTL, PDIP-20

8000

Effective Inventory

Image for reference only

Manufacturer Part:

SN74LS373N

Package:

PDIP-20 (24.33 x 6.35 x 5.08mm, 2.54mm pitch, through-hole)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The SN74LS373N is an octal transparent D-type latch with 3-state outputs from Texas Instruments, featuring separate output enable and latch enable controls in a 20-pin PDIP package.

Key Specifications

Number of Bits 8 (octal)
Logic Family LS (Low-power Schottky)
Function Transparent D-type latch
Supply Voltage 4.75V to 5.25V (5V nominal)
Propagation Delay (D to Q) 18ns typical
Latch Enable to Output 27ns typical
Output Type 3-state (high-impedance when disabled)
Output Enable (OE) Active-low (single pin controls all 8 outputs)
Output Drive (IOL/IOH) 24mA / -2.6mA
Operating Temperature 0°C to +70°C
Package PDIP-20 (24.33 x 6.35mm)

Features

  • 8-bit transparent latch with 3-state outputs
  • Single latch enable (LE) controls all 8 latches
  • Single output enable (OE) controls all 8 outputs
  • When LE is HIGH, outputs follow inputs (transparent)
  • When LE goes LOW, data is latched and held
  • 3-state outputs for bus-oriented applications
  • Direct replacement for 74LS373 from any manufacturer

Applications

  • Microprocessor address latch
  • Data register and hold register
  • Bus buffer and isolation
  • I/O port output register
  • Demultiplexed bus systems
Product Introduction: SN74LS373N Product Introduction

The SN74LS373N from Texas Instruments is an 8-bit transparent D-type latch with 3-state outputs, designed for bus-oriented applications in microprocessor and digital systems. When the Latch Enable (LE) input is HIGH, the latch is transparent—each output (Q) follows its corresponding data input (D). When LE transitions LOW, the data present at the inputs is latched and held at the outputs, regardless of subsequent input changes. The Output Enable (OE) input, when LOW, enables the 3-state output drivers; when OE is HIGH, all outputs enter the high-impedance state, effectively disconnecting the latch from the bus. This allows multiple SN74LS373 devices to share a common data bus. The device is commonly used in 8051 and similar microprocessor systems to demultiplex the address/data bus by latching the address on the falling edge of ALE. The N suffix denotes the PDIP-20 through-hole package.

Working Principle: SN74LS373N Working Principle

The SN74LS373N contains eight identical D-type transparent latches with common control inputs. Each latch has a data input (D) and a 3-state output (Q). When LE is HIGH, the latch is transparent: Q follows D with an 18ns propagation delay. This means the latch acts as a wire—data passes through unimpeded. When LE transitions from HIGH to LOW, the current D value is captured and held on Q. Subsequent changes on D are ignored until LE goes HIGH again. The OE control is independent of LE. When OE is LOW, the 3-state output buffers are active and Q drives the bus. When OE is HIGH, the output buffers enter the high-impedance state (both pull-up and pull-up transistors OFF), regardless of the latched data. This allows multiple 373 devices to share the same bus—only one should have OE LOW at a time. The typical application in 8051 systems: the multiplexed AD0-AD7 bus connects to the D inputs; the ALE signal connects to LE. During the address phase, ALE is HIGH and the address flows through to Q. When ALE falls, the address is latched. The bus then switches to data, but the latched address remains on Q for the duration of the bus cycle.

Pin Description: SN74LS373N Pin Definition and Functions
Pin Name Type Description
1 OE Input Output enable (active low, 3-state control)
2 1Q Output Latch 1 output (3-state)
3 1D Input Latch 1 data input
4 2D Input Latch 2 data input
5 2Q Output Latch 2 output (3-state)
6 3Q Output Latch 3 output (3-state)
7 3D Input Latch 3 data input
8 4D Input Latch 4 data input
9 4Q Output Latch 4 output (3-state)
10 GND Power Ground
11 LE Input Latch enable (HIGH=transparent, LOW=latched)
12 5Q Output Latch 5 output (3-state)
13 5D Input Latch 5 data input
14 6D Input Latch 6 data input
15 6Q Output Latch 6 output (3-state)
16 7Q Output Latch 7 output (3-state)
17 7D Input Latch 7 data input
18 8D Input Latch 8 data input
19 8Q Output Latch 8 output (3-state)
20 VCC Power Supply (4.75V to 5.25V)
Application Scenarios: In which products and applications is SN74LS373N used
  • Mux Bus Demux: 8051 ALE signal latches lower address byte from multiplexed AD0-AD7 bus
  • Output Register: Write data to latch, disable LE; data holds on outputs until next write
  • Bus Isolation: OE=HIGH disconnects latch from shared bus; OE=LOW when this device drives the bus
  • Input Port: External signals pass through transparent latch when LE=HIGH; latch on LE=LOW to freeze during read
  • Pipeline Stage: LE strobes at each clock phase to create an 8-bit pipeline register
Alternative Models: What chips are recommended as replacements for SN74LS373N
Model Manufacturer Key Difference Package Supply
74LS373N TI/Nexperia Original TTL version with 5V-only supply, typical propagation delay 10-15ns DIP-20 5V TTL
74LS373D TI/Nexperia Surface-mount SOIC version of LS with identical logic function SOIC-20 5V TTL
74HC373D TI/Nexperia CMOS version with wide 2-6V supply range, lower power consumption and higher noise immunity SOIC-20 2-6V CMOS
74HC373N TI/Nexperia Through-hole DIP version of HC family for prototyping and repair DIP-20 2-6V CMOS
74HCT373D TI/Nexperia CMOS with TTL-compatible input levels, ideal for mixing with LS devices at 5V SOIC-20 4.5-5.5V TTL-in
74HCT373N TI/Nexperia Through-hole DIP version of HCT family for prototyping and repair DIP-20 4.5-5.5V TTL-in
74LVC373D TI/Nexperia Low-voltage CMOS for 1.65-3.6V modern logic with 24mA output drive and bus-hold inputs SOIC-20 1.65-3.6V CMOS
74LVC373N TI/Nexperia Through-hole DIP version of LVC family for prototyping and repair DIP-20 1.65-3.6V CMOS

The 74373 is a Octal Transparent Latch with 3-State Output. Family variants span from the original LS TTL (5V only) to modern LVC/AUP (down to 0.8V). HC and HCT versions offer 2-6V CMOS operation with HCT providing TTL-compatible input thresholds for mixed 5V systems. CD4000-series equivalents offer the widest 3-18V supply range at the cost of lower switching speed. DIP packages (N suffix) are through-hole; SOIC (D suffix) and TSSOP are surface-mount.

Recommend Parts

0751.0505

Schurter fuse, 0751.0505

Brand: schurter

Package: See datasheet

IN STOCK: 6768pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TL062CDR

Low-power JFET-input dual op-amp, 1MHz GBW, 30pA Ibias, SOIC-8, ±3.5V to ±18V

Brand: TI

Package: SOIC-8 (3.9 x 4.9 x 1.75mm)

IN STOCK: 11576pcs

Cargo cycle: 3-7 Days

The minimum order is 1

P89LPC922FN

8-bit 80C51 MCU, 8KB Flash, 256B RAM, 20-SSOP

Brand: NXP

Package: SSOP-20 (7.2 x 5.3 mm)

IN STOCK: 12628pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AC0603JR-070RL

Chip Resistor, 0Ω (Zero Ohm Jumper), ±5%, 0603 (1608 Metric), 1/10W (100mW)

Brand: Yageo

Package: 0603 (1608 Metric)

IN STOCK: 100000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LMR34206FSC5RNXRQ1

42V 2A sync buck, 5V fixed, 2.2MHz, 18uA Iq, AEC-Q100, SOT-563

Brand: TI

Package: SOT-563 (1.6 x 1.2 x 0.55mm)

IN STOCK: 6500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AO3402

30V N-channel trench MOSFET, SOT-23, 4A, RDS(on) 52m ohm max @ 10V, Qg 10nC, 2.5V gate drive capable, -55C to +150C.

Brand: aosmd

Package: SOT-23 (2.9 x 1.6 x 1.25mm)

IN STOCK: 14066pcs

Cargo cycle: 3-7 Days

The minimum order is 1